Brinkmann 800-2700-0 Owner's Manual

OWNER’S MANUAL &
OPERATING INSTRUCTIONS

®

700,000 CANDLEPOWER

WARNING

READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS IN THIS MANUAL TO AVOID

PERSONAL INJURY OR PROPERTY DAMAGE.

12-VOLT SPOTLIGHT

• Never attempt to wipe or clean the inner reflective surface of the
reflector. Touching or wiping the surface will damage it permanently.

• The lens is made of optical-quality, tempered glass. As with all glass,
avoid dropping or sharp impact on spotlight.

• Do not allow the hot lens to come in contact with water or materials
subject to heat damage.

• This spotlight is weather resistant. It is not waterproof. Do not use the
spotlight under water or store outdoors for extended periods.

• Only use a Brinkmann 12-volt, halogen bulb that is designed for your
Q-Beam spotlight. Use of any other bulb may result in poor
performance and may damage your spotlight.

• After months of use, cigarette lighters can build up corrosion that may
prevent your Q-Beam spotlight from making good contact. It may be
necessary to clean the inside of your cigarette lighter receptacle with a
fine emery cloth. Before cleaning receptacle, remove the fuse to prevent it
from shorting out.

1

• Never place spotlight lens (face) down when light is on or if it was recently on. Doing so could burn/ignite
surfaces such as seats, carpeting, etc. and cause serious property damage. Always turn spotlight OFF and
unplug from source when not in use.

• To prevent serious damage to eyesight, never look into spotlight when light is on. Do not shine light into the
face of someone else.

• Do not touch lens of spotlight when light is on or if it was recently on. The lens will be hot and could cause
serious burns.

• Keep battery clips or cigarette lighter plug dry and out of water at all times.

• Do not place spotlight in water. Keep all components dry and out of water at all times.

• Do not allow children to handle or operate this spotlight.

• Do not use this product for other than its intended use.

• Do not operate in close proximity of combustible or flammable materials.

• Do not attempt to operate spotlight if cord, plug, bulb or any part of the spotlight is damaged or corroded.

USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR SPOTLIGHT.

FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL

COULD RESULT IN BODILY INJURY OR PROPERTY DAMAGE.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

IMPORTANT SAFETY WARNINGS

READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS

IN THE OWNER’S MANUAL BEFORE OPERATING SPOTLIGHT.

WARNING

Tips to Avoid Damage to

Your Q-Beam Spotlight

OPERATING INSTRUCTIONS

READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS IN THE OWNER’S MANUAL

BEFORE OPERATING SPOTLIGHT.

Step 1: To activate spotlight, plug the cigarette lighter adapter

into a cigarette lighter receptacle.

Step 2: Depress trigger switch in handle to turn spotlight ON.

Release trigger switch to turn spotlight OFF.

WARNING: Never place spotlight lens face down when light is

on or if it was recently on. Doing so could
burn/ignite surfaces such as seats, carpeting, etc.
and cause serious property damage. Always turn
spotlight off and unplug from power source when
not in use.

Step 3: To lock trigger switch to ON, depress trigger switch and

slide locking button on back of handle to LOCK. To
unlock and turn spotlight OFF, slide locking button back
to UNLOCK.

NOTE: The locking button can also be used to lock spotlight in

the OFF position to prevent accidental activation.

To Replace Bulb

Rear

Housing

Front

Housing

Only use a Brinkmann halogen bulb that is designed for the
Q-Beam 700,000 CP spotlight as a replacement. Use of any other
bulb may result in poor performance and may damage your
spotlight.

IMPORTANT: Do not touch the glass part of bulb with fingers as

natural oils affect the life and performance of bulb.
Handle bulb by metal end only.

Step 1: Disconnect spotlight from power source.
Step 2: Remove the two screws from top and bottom of front

housing (see Figure 1).

Step 3: Holding the front housing securely, slowly remove the

rear housing, being careful not to pull wire connections
inside.

2

FIGURE 1

Locking
ON/OFF
Button