Brilliant Wonders 25650-100 Series, 25650-100-000, 25650-100-300, 25650-100-100 Operation & Installation Quick Reference

Download

Brilliant

Wireless Touch LED RGB Remote Controller

25650-100 Series

OPERATION & INSTALLATION QUICK REFERENCE

Wonders

LED WATERFALLS

WARNINGS AND IMPORTANT SAFETY PRECAUTIONS

Be sure that the electrical system prior to installation conforms to all local codes and

ordinances. A licensed or certied electrician must install the electrical system to insure

that it follows all of the requirements of the National Electric Code (NEC). The electrician may need to consult the local building inspector for code interpretation before installing the 25650-100 wireless controller.

Attention Installer: This manual contains important information about the installation, operation, and safe use of this product. This information should be given to the owner and/or operator of this equipment. When installing and using this electrical equipment, basic safety precautions should always be observed.

Read all safety precautions and important instructions before attempting any electrical

wiring. Ensure that all power has been turned o at the power source. Failure to follow

safety warnings and instructions can result in severe injury, death, or property damage. CMP recommends installation to be performed by a licensed professional.

IMPORTANT NOTICE

INTRODUCTION

Thank you for choosing the CMP 25650-100 series controller. If you haven’t already done so, please take a moment to read our safety information. To fully enjoy the features of this controller, please read the entire manual before operating. Following these safety requirements should prevent any damage to your new controller.

1. PERFORMANCE PARAMETERS

CONTROLLER

• Power input: 12 Volt DC

• Max Current: 5A x 3CH Max 15A

• Maximum load power: 180 Watts

• Change Mode: 32

• Scale Levels: 65536 steps/RGB (16Bits/CH)

• Control Function: 8 touch buttons

• Operating temp: -30°C to 55°C

• Dimension: L8.3 in. x W1.6 in. x H1.2 in.

• Weight(net): 180g

REMOTE

• Power: Rechargeable 5 Volt DC built in Lithium battery

• Working Current: 30mA

• Working Frequency: 2.4 GHZ

• Battery Capacity: 1000mAh

• Charge Time: <4 hours

• Normal Usage Time: 30 days

• Number of charge cycles: 500

• Operating range: up to 90 feet (dependent on environment)

• Operating temp: -30°C to 55°C

• Dimension: 5.7”L x 2.2”W x 0.9”H

• Weight(net): 200g

2. KEY FEATURES

set successfully when heard takq

Descri p ti on

No.

Mode

Descri p ti on

No.

Mode

The remote control has 18 function buttons and 1 full-color touch circle. The controller has 8 touch buttons.

HOW TO PAIR THE CONTROLLER WITH THE REMOTE Press the “ON/OFF” key on the controller until you hear the “BEEP” sound, then press the “1” key on the remote to activate the connection between the controller and remote

control. Press the “2” key to cancel the connection

Contr ol ler sig n

PAUSE

MODE

SPEED SPEED

BRT BRT

3. LIGHT MODES

Static red

Static green

Static blue

Static yellow

Static purple

Static cyan

Static white

RGB skipping

7 colors skipping

White strobe

7 colors strobe

Red fade out and fade in

Green fade out and fade in

Blue Fade out and fade in

Yellow fade out and fade in

Purple fade out and fade in

Remot e co ntrol s ig n

brightness adjustable

speed/brightness adjustable

Butto n

ON/OFF

PAUSE

MODE+ MODE-

SPEED+ SPEED-

BRT+ BRT-

Full Color Touch Circle

Nine DIY Keys

Descr ip tion

ON/OFF:

PAUSE

MODE+ MODE-/

Pre ss the ke ys to sel ect next mo de or b ack t o pre vious m ode.

SPEED +/SPE ED-

Press the keys to quicken and slow color change speed

BRT+/ BR T-

Pre ss the ke ys to inc rease or de cre ase b rig htnes s, kee p press ing to adju st br igh tne ss cont inuou sly

Whe n touch ing the f ull-c olor circ le, L ED li ght s will sho w the sam e color as th e cir cle .

Press a key for 3 seconds and the controller will save the current function mode automatically. Save up to 9 modes and save repeatedly as well. Press the “PLAY” key to cycle all saved modes. (this only plays the dynamic effects, static effects will be skipped automatically)

Tur n on/ off t he Co ntr oller.

Press once to stay at current color Press again to resume color changing Press this button in 3 seconds, and the buzzer can be turned on or off

Cyan fade out and fade in

White fade out and fade in

RGB fade out and fade in

Red Green color smooth

Red Blue color smooth

Green Blue color smooth

Red Yellow color smooth

Green Cyan color smooth

Blue purple color smooth

Green Yellow color smooth

Blue Cyan color smooth

Red Purple color smooth

Blue White color smooth

Yellow Purple Cyan color smooth

RGB color smooth

full color smooth

speed/brightness adjustable

3. INSTALLATION AND WIRING DIAGRAM

Connected to RGB module as an example

CLASS 2

POWER SUPPLY

AC L

110V

AC22 0V

DC12 V

GREEN

H H HH

LED M ODULE

LED M ODUL

BLACK

RED

LED M ODULE

Note: Ensure all wire connections and polarities are correct before applying power.

CONTROLLER MOUNTING

You must provide the controller enclosure

a. The enclosure or junction box must be installed per the National Electric

Code (NEC) requirements as well as comply with any local codes and regula-

tions b. All wire used from the controller box to luminaire must be in conduit. c. Min size of controller box must be 9" x 2" x 1.5". d. The enclosure must be non-metallic(plastic) to ensure adequate RF signals

are achieved. e. For product longevity, ensure proper ventilation where both the controller

and power supply may be mounted inside the same enclosure in elevated

outdoor temperatures.

WHITE

CMP Plastic Outdoor Box

for Controller Only

25650-100-210

DO NOT INSTALL ANY OTHER ITEM INSIDE CONTROLLER ENCLOSURE.

State listed Class 2 Power Supply and Listed outdoor junction box will have to be purchased and installed.

4. CHARGING METHODS

H H HH

40m m

16m m

15m m

10m m10m m

203 mm

20m m

211m m

30mm

1. When charging, connect the USB cable to the mobile charger or a computer

with USB interface. The remote control must be turned on to charge.

2. The blue indicator light ickers while charging, and will turn green when

fully charged

3. No memory eect in the lithium battery of the remote control. Follow the

standard charging procedure even for the rst three charges. There is no

need to over charge.

4. The red indicator light ickers when the battery is low and needs to be

charged soon. Charging in low battery will eect battery life.

5. REPLACEMENT PARTS & DIMENSIONS GUIDE

COLORWHEEL REMOTE

LED CONTROLLER

P/N DESCRIPTION

25650-100-300 REMOTE & CONTROLLER

25650-100-000 COLORWHEEL REMOTE

25650-100-100 CONTROLLER

55m m

22m m

everything matters.

145 mm

40m m

30mm

211m m

20m m

H H HH

203 mm

15m m

16m m

10m m10m m

www.c-m-p.com

sb0913

Brilliant Wonders 25650-100 Series, 25650-100-000, 25650-100-300, 25650-100-100 Operation & Installation Quick Reference

Specifications and Main Features

Frequently Asked Questions

User Manual