Brilliant BHA120US-WH3 Installation Guide
Home Control
Installation Guide
THREE SWITCHES
Please confirm the following:
Welcome!
This short installation guide will
help you upgrade your home
with Brilliant.
It is important that you first
review all of the instructions
to ensure you are comfortable
with the required steps.
If you are unsure about or
uncomfortable with the
installation, go to
brilliant.tech/install for more
instructions, and/or help with
finding a qualified electrician.
Thank you!
The Brilliant Team
Is your circuit 120V?
A 120V circuit is required, and is standard in North
American homes.
Is your wiring up to code, with Neutral and
Ground wires?
Both Neutral and Ground wires are required, and
present in most modern homes. Refer to Steps 5
and 6 for more details about wires.
Are you replacing a single or 3-way/multi-way
switch?
If you are replacing a 3-way/multi-way switch,
meaning that you can control the same light(s)
from more than one switch, you should confirm
that the Brilliant can support your configuration.
Refer to Step 1 for pictures of the supported
configurations.
Do you have the right tools?
A size 2 screwdriver is needed to remove your old
switch, and to install Brilliant.
Is your gang box a standard size?
A gang box is the electrical box in the wall, behind
the light switch. The box must have an interior
width of no less than 137mm, and an interior height
of no less than 70mm. Standard sizes will work.
In the Box
FaceplateBase
It’s important to
only use supplied
screws.
11 Wire Nuts 11 Extra Wires
(optional)
x3
(optional)
10 STEPS
To A Better Home
Warning / Attention
Installing this product involves handling high voltage wiring.
Each step of the enclosed instructions must be followed
carefully. To avoid fire, personal injury, or death, turn o your
circuit breakers and follow the proper safety precautions
UNSURE ABOUT HANDLING ELECTRICAL WIRING?
L’installation de ce produit requiert la manipulation
de câbles électriques à haute tension. Veuillez suivre
soigneusement les instructions ci-jointe étape par étape.
Afin d’éviter tout risque d’incendie, de blessure, ou de mort,
coupez votre disjoncteur ou coupe-circuit et suivez les
VOUS AVEZ DES DOUTES AU SUJET DE VOTRE CÂBLAGE
TRAVAILLEZ AVEC UN ÉLECTRICIEN QUALIFIÉ.
before proceeding.
CONSULT A QUALIFIED ELECTRICIAN.
consignes de sécurité avant de continuer.
ÉLECTRIQUE?
1 Check Compatibility
If your light is controlled by...
2 Switches
Make sure Brilliant is compatible with
the location where you’re installing it.
If the 120V switch you are going to
replace activates a light that other
switches also control (often referred to
as 3-way or multi-way lighting), please
find the picture of your setup on the next
pages to confirm compatibility.
Will work: Two Brilliant controllers
Will work: Brilliant and non-dimming switch
(at either end)
Non-Dimming
Won’t work: Brilliant and dimming switch
(at either end)
Dimming
One circuit shown for simplicity.
See Step 6b, or visit
http://support.brilliant.tech
for more info on wiring multi-way circuits.
If your light is controlled by...
3 or More Switches
Base
2 Turn O Power
Will work: All Brilliant controllers
(connected through WiFi)
Will work: Brilliant at either end (or both ends) and a
non-dimming switch
Non-Dimming
Won’t work: Brilliant in the middle
Won’t work: Brilliant at the end, with a dimmer
anywhere else
Dimming
Turn the circuit breaker to OFF.
ON OFF ON OFF
Kitchen
TV Room
Dining
Bedroom
Stairwell
Guest
Patio
Garage
Before Proceeding
Avant de continuer
Confirm you’ve turned o the right breaker by flipping your light
switch on and o. If you have turned o the correct breaker, your
light won’t turn on.
Confirmez que le bon coupe-circuit est éteint en utilisant
l’interrupteur à remplacer. Si le bon coupe-circuit est
eectivement éteint, vos lumières ne devraient pas s’allumer.
Loading...