Briggs & Stratton CleanShot 020206-0 Owner's Manual

CleanShot TM ,

__lw POWERPRODUCTS

2050PSI

Owner's Manual/Manual del Propietario

Questions? Help isjust a moment away!

Preguntas? Laayudaes justaun momento lejos!

Call: Pressure Washer Helpline

Llame:Linea Directa del Lavador a Presi6n - 1-800-743-4115 M-F 8-5 CT

CleanShotTM isa trademark of Briggs& Stratton Power Products.

CleanShotTM es una marca registrada de Briggs& Stratton Power Products.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

IU!!!U!!U!!,,EFFERSO,,,,W,SCONS,,,,,U.S.A.

0 3 Model No.020206-0 (2050 PSIPressureWasher) Manual No. 194140GS Revision I (01/26/2004)

CleanShotTM 2050 PSIPressureWasher

TABLE OF CONTENTS

SafetyRules.................................... 2-4

Know Your PressureWasher........................ 5

Assembly...................................... 6-7

Operation .................................... 8- I0

Product Specifications ............................ I I

Maintenance................................. I I- 13

Storage........................................ 14

Troubleshooting ................................. 15

Replacement Parts ............................ 16-17

Notes ......................................... 18

Warranty ...................................... 19

EQUIPMENT

DESCRIPTION

_Read this manual carefully and become familiar

with your pressure washer.Know its

applications, its limitations and any hazards
involved.

This manual contains informationfor a pressure washer
that operates at 2,050 PSIat a flow rate of 2.0 gallonsper
minute.This high quality residential system features axial
cam pump with stainless steel pistons, automatic cool down
system,chemical injection system,adjustable spray nozzle,
turbo nozzle, utility brush with adapter,tool bag,safety
goggles,heavyduty 25' hose, and more.

Every effort hasbeen madeto ensure that information in

this manual is accurate and current. However, we reserve
the right to change,alter or otherwise improve the product

and this document at any time without prior notice.

In the State of California a spark arrester is required by lawI

(Section 4442 of the California Public ResourcesCode). I
Other states may havesimilar laws.Federal lawsapply on
federal lands.If you equip the muffler with asparkarrester,

it must be maintained in effective working order.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol (_,) is used with asignalword
(DANGER, CAUTION,WARNING), a pictorial and/or a

safety messageto alert you to hazards.DAN('_I'R indicates
a hazard which, if not avoided,will result in death or serious

injury. WARNING indicatesa hazard which, if not avoided,
couldresult in death or serious injury. CAUTION
indicates a hazardwhich, if not avoided,might result in
minor or moderate injury. CAUTION, when used
without the alert symbol, indicates a situation that could
result in equipment damage.Follow safety messagesto
avoid or reduce the risk of injury or death.

WARNING I

The engine exhaust from this product contains I
chemicals known to the State of California to cause

cancer, b rth defects, or other reproduct ve harm.

Hazard Symbols and Meanings

Toxic Fumes Electrical Shock

Slippery Surface Fall Fluid Injection

Fire Explosion Hot Surface

Moving Parts FlyingObjects Kickback

/

2

CleanShotTM 2050 PSIPressureWasher

CleanShor

DANGER

Operate pressure washer ONLY outdoors.

Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

Readall instructionswith mask so you are certain the maskwill
provide the necessaryprotection againstinhalingharmful vapors.

WARNING

Keepwater spray awayfrom electric wiring or fatal electric

shock may result.

WARNING

Keepspray nozzle between 8 to 24 inchesawayfrom cleaning

surface.
Operate this unit on a stable surface.
The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.
Beextremely careful ifyou must usethe pressure washer from

a ladder,scaffolding or anyother relatively unstable location.

Firmly grasp spraygunwith both hands when usinghigh
pressure sprayto avoid iniuryif gun kicks back.

WARNING

WHEN ADDING FUEL

Turn pressure washer OFF and let it cool at least 2 minutes

before removing gas cap.
Fill fuel tank outdoors.

DO NOT overfill tank.Allow space for fuel expansion.
Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.
DO NOT light a cigarette or smoke.

¢VHEN OPERATING EQUIPMENT

DO NOT tip engine or equipment at angle which causes fuel
to spill.

DO NOT spray flammable liquids.
'HEN TRANSPORTING OR REPAIRING EQUIPMENT

Transport/repair with fuel tank EMPTY or with fuel shutoff
valve OFE

_HEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

Store away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

WARNING

NEVER aim spray gun at people, animals or plants.
DO NOT allow CHILDREN to operate pressure washe_
NEVER repair high pressure hose.Replace it.
Keep high pressure hose connected to pump and spray gun

while system is pressurized.
ALWAYS RELIEVEwater pressure eachtime engine is stopped
by squeezing trigger on spray gun.

/

3

CleanShotTM 2050 PSIPressureWasher

WARNING

DO NOT touch hot surfaces.

Stay dear of exhaust gases.
Allow equipment to cool before touching.

WARNING

DO NOT wear loose clothing, jewelry or anything that may
be caught in the starter or other rotating parts.

Tie up long hair and remove jewelry.

WARNING

Always wear eye protection when using this equipment or in
vicinity of where equipment is in use.

WARNING

Disconnect spark plug wire from spark plug and place wire

where it cannot contact spark plug.

CAUTION

DO NOT tamper with governed speed.
DO NOT operate pressure washer above rated pressure.

CAUTION

DO NOT secure spray gun in open position.
DO NOT leavespray gun unattended while machine is
running.

NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working orde_

Always be certain spraygun,nozzles and accessories are
correctly attached.

CAUTION

DO NOT point spray gun at glasswhen in iet spray mode.
NEVER aim spray gun at plants.

CAUTION

tf you have questions about intended use,askdealer or
contact Briggs& Stratton Power Products.

NEVER operate units with broken or missing parts, or
without protective housing or covers.

DO NOT by-pass any safety device on this machine.
Before starting pressure washer in cold weather, check all

parts of the equipment to be sure ice has not formed there.
NEVER move machine by pulling on highpressure hose.Use

handle provided on unit.
Check fuel system for leaksor signsof deterioration, such as

chafed or spongy hose, loose or missingclamps, or damaged
tank or cap.Correct all defects before operating pressure
washe_

This equipment is designed to be used with Briggs& Stratton
Power Products authorized parts ONLY. If equipment is used

with parts that DO NOT comply with minimum specifications,
user assumesall risks and liabilities.

/

4

CleanShotTM 2050 PSIPressureWasher

CleanShot

KNOWYOUR PRESSURE WASHER

Read this owner's manual and safety rules before operating your pressure washer.

Compare the illustrationswith your pressure washer to familiarize yourself with the locations of various controls and
adjustments. Savethis manualfor future reference.

Air Cleaner

Recoil Starter

\

Primer Bulb

High Pressure Outlet

& Water Inlet

FueiTank

Air Cleaner-- Dry type filter element limits the amount
of dirt and dust that gets in the engine.

Automatic Cool Down System -- Cycles water
through pump when water reaches 125°-155°F.Warm
water will discharge from pump onto ground.This

system prevents internal pump damage.

Fuel Tank- FIlltank with regular unleaded fuel.
High Pressure Hose (not shown) -- Connect one end

to water pump and the other end to spraygun.

High Pressure Outlet -- Connection for high pressure

hose.

Pump equipped with

Automatic Cool Down System

DataTag (not shown, near rear of base plate) -
Provides model and serial number of pressure washer.
Pleasehave these readily availableif calling for assistance.

Primer Bulb -- Preparesa cold enginefor starting.

Pump -- Devetops high water pressure.
Recoil Starter -- Used for starting the engine manually.

Spray Gun (not shown) -- Controls the application of

water onto cleaning surfacewith trigger device.Includes
safety latch.

Water Inlet -- Connection for garden hose.

I

5

CleanShotTM 2050 PSIPressureWasher

CleanShot

ASSEMBLY

IMPORTANT: Readentire owner's manualbefore you

attempt to assembleor operate your new pressure washer.

Remove Pressure Washer From

Carton

I. Removethe parts bag,accessories,and inserts included

with pressure washer.

2. Slicetwo corners at the end of carton from top to
bottom so the panel can be folded clown fiat.

3. Removepressure washer from carton.

Carton Contents

Items in the carton include:

Main Unit
High Pressure Hose

SprayGun

Nozzle Extension

Turbo Nozzle
Utility Brush with Adapter

Accessory Storage Bag
SafetyGoggles

Oil Bottle

Parts Bag(which includesthe following):

Owner's Manual

EngineManual

Owner's Registration Card

PREPARING PRESSURE

WASHER FOR USE

If you have anyproblems with the assemblyof your

pressure washer or if parts are missingor damaged,callthe
pressure washer helpline at 1-800-743-4115. If callingfor
assistance,pleasehave the model, revision, and serial
number from the data tag available.

To prepare your pressure washer for operation, you
will need to perform these tasks:

I. Fill out and sendin registration card.

2. Add oil to engine crankcase.

3. Add fuel to fuel tank.

4. Connect high pressure hose to spraygun and pump.

5. Connect water supply to pump.

6. Attach nozzle extension to spray gun.

Add Engine Oil and Fuel

• Placepressurewasher on a level surface.

CAUTION

• Refer to engine manualfor oil andfuel fill information.

• Damageto equipment resulting from failure to follow this
instructionwill void warranty.

• Refer to engine owner's manual and follow oil and fuel
recommendations and instructions.

NOTE: Check oil often during engine break-in. Refer to
engine owner's manual for recommendations.

/

6

CleanShotTM 2050 PSIPressureWasher

Connect Hose and Water Supply to

Pump

IHPORTANT: To avoid pump damage,you must assemble

the nozzle extension to the spray gun and attach atl hoses
before you start the engine.

I. Uncoil high pressure hose and attach one end of hose

to baseof spray gun (Figure I).Tighten by hand.

Connect high pressure

hose here

NOTE: Remove and discard alt pump shippingcapsbefore

attaching hoses.

2. Attach other end of high pressure hoseto high
pressure outlet on pump (Figure 2).Tighten by hand.

4. Run water through your garden hose for 30 seconds
to cleanout any debris.

IMPORTANT: DO NOT siphon standing water for the
water supply.Use ONLY cold water (lessthan IO0°E).

5. Connect the garden hose (not to exceed 50 feet in

length)to the water inlet.Tightenby hand (Figure 3).

CAUTION

• Damage to equipment resulting from failure to follow this

instructionwill voidwarranty.

6. Turn ON the water and squeezethe trigger on the
gun to purge the pump system of air and impurities.

WARNING

Always wear eye protection when usingthis equipment or in
vicinity of where equipment isin use.

Before starting the pressure washer,be sure you are wearing
adequate eye protection.

.

Before connectinggarden hose to water inlet,inspect

inlet screen (Figure 3). Clean screen if it contains

debris or have it replaced if damaged.DO NOT RUN

PRESSUREWASHERIF INLET SCREEN ISDAMAGED.

Inspectintet

screen,DONOT

useif damaged;

cleanif dirty.

CHECKLIST BEFORE

STARTING ENGINE

Review the unit's assemblyto ensure you haveperformed
altof the following.

I. Check that oit has been added to proper level in the

engine crankcase.

2. Add proper gasoline to fuel tank.

3. Check for properly tightened hose connections.

4. Check to make sure there are no kinks,cuts, or
damageto high pressure hose.

5. Provide a proper water supply at an adequateflow.

6. Be sure to read "Safety Rules" and"HowTo UseYour
PressureWasher" before usingpressure washer.

/

7

CleanShotTM 2050 PSIPressureWasher

CleanShot

HOW TO USE YOUR

PRESSURE WASH ER

If you haveany problems operating your pressurewasher,

pleasecall the pressurewasher helplineat 1-800-743-4115.

How to StartYour Pressure Washer

To start your pressure washer for the first time, follow
these instructions step-by-step.This starting information
also applies if you have let the pressure washer sit idlefor
at least a day.

I. Placepressure washer near an outside water source

capableof supplying water at a flow rate greater than

3.0gallons per minute and no lessthan 20 PSIat
pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected to
spray gun and pump. See"PreparingPressureWasher

for Use" for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure
washer pump. Turn ON water.

CAUTION

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Attach adjustable nozzle extension to spray gun
(Figure 4).Tighten by hand.

6.

Position nozzle in low pressure mode (see"How to
Use the Adjustable Nozzle") and squeezetrigger on
spray gun to relieve air pressure caused by turning ON
water.Water will flow out of spray gun in a thin
stream. Continue to hold trigger until there is a steady
stream of water and no air remains in system.This wilt
make it easier to pull start engine.Releasetrigger.

7. Engage safety latch to spray gun trigger (Figure 5).

SafetyLatch

8. Start engine according to instructions given in engine
owner's manual.

• Squeezetriggeron sprayguneachtime recoil starter is
pulledandenginefailsto start.

NOTE: Always keep the throttle lever in the "Fast"
position when operating the pressure washer.

How to StopYour Pressure Washer

I. Let engine idle for two minutes.

2. Turn engine off according to instructions given in
engine owner's manual.

3. Squeeze trigger on the spray gun to relieve

pressure in the hose.

NOTE: A small amount of water will squirt out when you

releasethe pressure.

How to Use the Adjustable Nozzle

You should now know how to START and STOP your
pressure washer.The information in this section will tell
you how to adjust the spray pattern andto apply detergent
or other cleaning chemicals.

CAUTION

I.

NEVER adjust spray pattern when spraying.
NEVER put handsin front of nozzle to adiust spray pattern.

Slide nozzle forward when you wish to adjust spray to
low pressure mode (Figure 6). Slide nozzle backward
to achieve high pressure.

I

8

CleanShotTM 2050 PSIPressureWasher

CleanShot

2.

Slide nozzle backward

for High Pressure

Mode

Slide nozzle forward for low

pressure mode and

detergent application

Point nozzle down towards a firm surface and press

trigger to test pattern (Figure 7).

3. Twisting nozzle adjusts spray pattern from a narrow
pattern to a fan pattern (Figure 8).

Rotate nozzle

counterclockwise for fan

spray pattern

Rotate nozzle clockwise

for narrow spray pattern

4. For most effective cleaning,keep spray nozzle from
8 to 24 inchesawayfrom cleaning surface.

5. If you get spray nozzle too close,especiallyusinghigh
pressure mode, you may damagesurfacebeing cleaned.

6. DO NOT get closer than 6 inches when cleaningtires.

Using the Turbo Nozzle

The turbo nozzle rotates the high pressure stream in a
rapid circular pattern.The high pressure spray is most
effective when the tip of the nozzle extension is held
between 8 to 24 inches from the surface being cleaned.

CAUTION

Always make sure the surface you will clean will not be
damaged by the high pressure spray by testing in a hidden area.

To attach the turbo nozzle to the spray gun:

I. Engagesafety latch to spraygun trigger.

2. Remove the nozzle extension from the spray gun, if
attached.

3. Attach the turbo nozzle extension to spray gun
(Figure 9).Tighten by hand.

4.

5.

\

Disengagesafety latch to spray gun trigger.
Always start the turbo nozzle at a distance,gradually

getting closer to the surface until you get the cleaning
force you want.

NOTE: Detergent cannot be applied with turbo nozzle.

Using the Utility Brush

The utility brush allows you to scrub surfaces with water
filtering through the bristles.

To attach the utility brush to the spray gun:

I. Engagesafety latch to spraygun trigger.

2. Tighten the adapter to the brush base.

3. Remove the nozzle extension from the spray gun, if
attached.

/

9

CleanShotTM 2050 PSIPressureWasher

CleanShot

4. Attach the brush with the adapter to the spray gun.
Tighten by hand (Figure 10).

NOTE:You must use the adapter to attach the brush to

the spray gun.

5. Disengagesafety latch to spray gun trigger.

Applying Detergent with the

Adjustable Nozzle

IMPORTANT: Use soaps designed specifically for

pressure washers. Household detergents could damage

the pump.

CAUTION

• Starting the engine without all the hoses connected and

without the water turned ON will damagethe pump.

• Damage to equipment resulting from failure to follow this
instruction will void warranty.

To apply detergent, follow these steps:

I. Reviewuse of adjustable nozzles.

2. Preparedetergent solution asrequired by job.

3. Placefilter end of chemical injection hose into
detergent container.

CAUTION

• When inserting the filter into a detergent solution bottle,
route the tube so asto keep it from inadvertentlycontacting

the hot mufflen

4. Slide adjustable nozzle forward to lowpressure mode.
Detergent cannot be applied with nozzle in high

pressure position.

5. Makesure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray
gun and pump. Start engine.

6. Apply detergent to a dry surface,starting at lower

portion of area to be washed and work upward, using
long,even,overlapping strokes.

7. Allow detergent to "soak in"for 3-5 minutes before
washingand rinsing. Reapplyas needed to prevent
surface from drying. DO NOT allow detergent to dry
on (prevents streaking).

IMPORTANT:You must flush the chemical injection
system after eachuse by placingthe filter into a bucket of

cleanwater, then run the pressure washer in low pressure
for I-2 minutes.

Pressure Washer Rinsing

For Rinsing:

I. Slide the nozzle backward to high pressure, pressthe

trigger and wait for the detergent to clear.

NOTE:You can also stop detergent from flowingby simply
removing chemical injection hose from bottle.

2. Keep the spraygun a safe distancefrom the area you
plan to spray.

WARNING

Keepspray nozzle between 8 to 24 inchesawayfrom cleaning
surface.

Operate this unit on a stable surface.
Be extremely careful if you must usethe pressure washer from

a ladder,scaffolding or anyother relatively unstable location.
Firmlygrasp spraygun with both handswhen using high

pressure sprayto avoid iniuryif gun kicks bac!c

3. Apply a high pressure spray to a small area,then check
the surfacefor damage.If no damage isfound, it is okay

to continuecleaning.

4. Start at the top of the areato be rinsed,working
down with same overlapping strokes asyou usedfor
washingand applyingdetergent

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for
3-5 minutes without pressingthe trigger on the spray gun,

circulating water in the pump can reachtemperatures
above 125°EThe system engagesto cool the pump by

discharging the warm water onto the ground.

/

10

SPECIFICATIONS

Outlet Pressure ..... 2050 psi

Flow Rate .......... 2.0 gallonsper minute (gpm)

Detergent .......... Use detergent approved for

pressure washers

Water Supply ...... Not to Exceed 100°F

Temperature

Automatic Cool .... Willcyclewhen water

Down System reaches 125°-155°F

ShippingWeight .... 48 Ibs.

GENERAL MAINTENANCE

RECOMMENDATIONS

The pressure washer warranty does not cover items that
have been subjected to operator abuse or negEgence.To

receive full value from the warranty, the operator must

maintain the pressure washer as instructed in this manual

• Some adjustments witl need to be made periodically to
properly maintain your pressure washer.

• All maintenance in this manual and the engine owner's
manual should be made at least once each season.

• Once a year you should clean or replace the spark plug,
clean or replace the air filter and check the spray gun
and adjustable nozzle extension assembly for wear.A
new spark plug and clean air filter assure proper fuel-air
mixture and help your engine run better and last longer.

Please refer to your engine owner's manual for more

details.

• If equipped with inflatabletires, keep the air pressure at
the value marked on the tire or within 15 and 40 psi.

Before Each Use

I. Check engine oil level.

2. Check water inlet screen for damage.

3. Check in-line filter for damage.

4. Check high pressure hose for leaks.

5. Check chemical injectionhose and filter for damage.

6. Check spray gun and adjustable nozzle extension

assemblyfor leaks.

7. Rinseout gardenhose to flush out debris.

PRESSURE WASH ER

MAINTENANCE

Check and Clean Inlet Screen

Examinethe screen on the water inlet.Clean it if the
screen isclogged or replace it ifscreen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaksfrom wear,
kinking,or abuse.Inspect the hoseeach time before using
it. Check for cuts,leaks,abrasions or bulging of cover,
damageor movement of couplings. If anyof these
conditions exist, replacethe hose immediately.

WARNING

NEVER repair high pressure hose. Replace it.
Replacement hose rating MUST exceed maximum pressure

rating of unit.

Check Chemical Injection Hose

Examinethe filter on the detergent tube and clean if

clogged.The tube should fit tightly on the barbed fitting.
Examine the tube for leaks or tears. Replace the filter or

tube if either is damaged.

Check Gun and Adjustable Nozzle

Extension

Examinethe hose connection to the spray gun and make

sure it is secure.Test the trigger by pressingit and making
sure it "springs back" into place when you releaseit. Put
the safety latch in the ON position and test the trigger.You
should not be able to press the trigger.

Purge Pump of Air and

Contaminants

To remove air from the pump, follow these steps:

I. Set up pressure washer asdescribed in"Preparing

PressureWasher For Use". Connect water supply and

turn water on.

I

II