Briggs & Stratton 7800849 User Manual

Not for

Reproduction

Parts Manual fo

r

22" STEEL DECK WALK BEHIND

COMMERCIAL MOWER

SERIES 20

DescriptionModel No.

7800849 CP215520HV

Briggs & Stratton Yard Power Products Group

535 Macon Road
McDonough, GA, 30253 U.S.A.
800-935-2967

Manual No.
Revision:

7106167

- 9/30/2013

Not for

Reproduction

Not for

Reproduction

s

PAGE GROUP

4

8
10
12
16
18
20

Handle Group
Wheels, Brackets & Latches
Deck, Engine & Blade Group
Drive System, Self Propelled
Transmission - Differential Group
Grass Bag & Adapter Group
Decal Group

Table Of Content

22" STEEL DECK WALK BEHIND
SERIES 20

Manual No.

3

TP 400-5566---CW-N

7106167

Not for

Reproduction

Handle Group

Manual No.

7106167 22" STEEL DECK WALK BEHIND

4

SERIES 20

Not for

Reproduction

Handle Group

Part No DescriptionItem Qty

1 7074411AYP 1 HANDLE, Upper
2 7023810YP 1 FOAM GRIP, 18.75
3 7074418AYP 1 BAIL, OPC Control (16.6” Wide)
4 7034872YP 1 CLIP, Zone Control
5 7074156AYP 1 HANDLE, Middle
6 7033985AYP 1 HANDLE, Lower, ADJ, LH
7 7033986AYP 1 HANDLE, Lower, ADJ, RH
8 7074140YP 1 PANEL, Control, No Electric Switch
9 703961 4 SCREW, 1/4-20 X .550, Self-Tapping, Zinc/Clear (Was 7900067 or 80005286)
10 7074473AYP 1 HANDLE, Clutch
11 7028407YP 1 GRIP, International Symbol, 4.6” Black
12 704031 1 PIN, 1/4 X 1.5”, Clevis, ZC/CL (Was 7011886, 7023792 or 80005708)
13 7014343YP 2 BUSHING, Flanged, .27 ID, Nylon, Black
14 704005 1 NUT, 1/4”, Push, Zinc/Clear (Was 7091020 or 80005599)
15 703234 1 SCREW, 1/4-20 X 1.5, Hex Head Cap, GR5, ZC/CL (Was 7090909, 7079577 or 80002713)
16 7102235YP 1 CABLE, Zone Control (60.3 Long)
17 703462 3 WASHER, 1/4 Internal Tooth Lock, YZ (Was 7090053 or 80004414)
18 703127 3 NUT, 1/4-20, G5 Zinc/Clear (Was 7090063, 7091576 or 80003586)
19 7023813SM 3 CLIP, Wiring Harness
20 7078026YP 1 CONTROL, Throttle, Honda, 50.81” L
21 7075308YP 1 KNOB, Throttle, Red
22 703163 2 SCREW, 1/4-20 X 2.0, Hex Head Cap, GR5, Zinc/Clear (Was 1921963, 90505 or 80003674)
23 7028488MA 1 GUIDE, 1/4-20, Rope, CL/ZC
24 15X145MA 1 NUT, 1/4-20, Nylock, GR A, Zinc/Clear (Was 703232, 7076978 or 80002730)
25 7034604YP 1 CABLE, Clutch Control, 41.25” L
26 7012121YP 1 COVER, Vinyl
27 7012122YP 1 SPRING, Clutch
28 7026219YP 1 CLAMP, 7/8” Double Cable
29 704063 6 BOLT, 5/16-18 X 1.50, Carriage Head, Short Neck, ZC/CL (Was 7091190 or 80005975)
31 7090391SM 6 WASHER, 5/16, Internal Lock, Zinc/Clear (Was 703587 or 80003683)
32 703465 6 NUT, 5/16-18, Hex, GR5, Zinc/Clear (Was 7091069, 7091511 or 80002725)
33 7074003YP 1 BRACKET, Shift
34 703589 1 SCREW, 3/8-16 x 2, Hex Head Cap, GR5, Zinc/Clear (Was 1923701, 7091305 or 80003522)
35 703964 2 WASHER, 7/16” ID, 1” OD, .060 Thk, Flat, ZC/CL (Was 7031961 or 80005597)
36 704004 2 WASHER, .406 ID X 1.0 OD X .063 Thk, Flat Nylon (Was 7028465 or 80005596)
37 7074113BMYP 1 LEVER, Shift
38 7075182YP 1 KNOB, Shift, Red
39 703351 1 SCREW, #8-32 X 0.50, Machine Fillister Head, Zinc/Clear (Was 7091167 or 80004404)
40 703460 1 NUT, #8-32, Hex, Zinc/Clear (Was 7091018 or 80004411)
41 704006 1 WASHER, 3/8” ID x 3/4” OD, Belleville, Zinc/Clear (Was 7028568 or 80005600)
42 703347 1 NUT, 3/8-16, Hex Center-Lock, GR B, Zinc/Clear (Was 7091585 or 80004408)
43 7074133YP 1 ROD, Speed Control (1/4-28 thread)
44 703350 1 WASHER, 5/16, Flat SAE, Zinc/Clear (Was 80004405)
45 704030 1 PIN, 5/16 X 1.044, Self-Locking Cotter, Zinc/Clear (Was 7034162 or 80005707)

Footnotes:

SERIES 20

Manual No.

5

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Handle Group

Manual No.

7106167 22" STEEL DECK WALK BEHIND

6

SERIES 20

Not for

Reproduction

Handle Group

Part No DescriptionItem Qty

46 703798 2 BOLT, 5/16-18 X .50, Carriage, Zinc/Clear (Was 7090731, 725993, 908156MA or 80004563)
47 690272MA 3 NUT, 5/16-18, Serated Lock Flange, GR5, Zinc/Clear (Was 7091601 or 80002728)
48 7046707BMYP 2 BRACE, Handle
49 703301 1 SCREW, 5/16-24 x 1 Hex Head Cap, GR 5, BZ (Was MT910828MA or 80003532)
50 9357MA 3 SCREW, 5/16-18 X .750, Flanged Whiz-Lock, GR5 (Was 1930591, 1960738, 7090595 or

80003531)
51 703118 2 WASHER, 7/8, Flat, GR5, Zinc/Clear (Was 7091130, 7900022 or 80003517)
52 703947 1 NUT, 5/16-18 X .625, Weld, ZC/CL (Was 7090733, 7090895 or 80005534)
53 7012114SM 1 BUSHING, Differential
54 7034179BMYP 1 LINK, Differential, Commercial
55 703896 1 NUT, 5/16-24, Hex Center Lock, GR B, Zinc/Clear (Was 7091606, 7090174, 7090222 or

80004848)
56 7073913YP 1 BELL CRANK, Black Zinc
57 7015753YP 2 BALL JOINT, 1/4-28
58 703461 3 NUT, 1/4-28 Hex, GR5, Zinc/Clear (Was 7090095 or 80004412)
59 703408 1 SCREW, 5/16-18 x 7/8 Hex Head Cap, GR 5, Zinc/Clear (Was 80004421)
60 7073822BMYP 1 BRACKET, Bell Crank
61 690272MA 5 NUT, 5/16-18, Serated Lock Flange, GR5, Zinc/Clear (Was 7091601 or 80002728)
62 703970 1 SPACER, .623 OD x .328 ID x .151 L (Was 7013849 or 80005375)
63 703167 1 SCREW, 5/16-18 x 1-1/4 Hex Washer Head Self-Tap (Was 1931202, 7091151, 7091524 or

80003681)

Footnotes:

SERIES 20

Manual No.

7

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Wheels, Brackets & Latches

Manual No.

7106167 22" STEEL DECK WALK BEHIND

8

SERIES 20

Not for

Reproduction

Wheels, Brackets & Latches

Part No DescriptionItem Qty

0010 703964 6 WASHER, 7/16” ID, 1” OD, .0 60 Thk, Flat, ZC/CL (Was 7031961 or 80005597)
0020 7600180YP 1 KIT, Fr ont Wheel Arm Assembly, RH (Was 7051886)
0020-20 7012325YP 2 LATCH, Height
0020-30 703839 2 BOLT, 5/16-18 X .750, Hex Washer Head Shoulder, Zinc/Clear (Was 7015761 or 80004422)
0020-50 7031017YP 1 WHEEL ARM, Front, Round Hole, RH, Clear
0030 7054246YP 1 ASSEMBLY, Wheel Arm, Long, RR (Was 7054230YP)
0030-10 703840 2 BOLT, 5/16-18 X 1.0, Hex Washer Head .435 Dia. Shoulder, ZC/CL (Was 7011078 or

80004423)
0030-20 703297 4 RETAINER, 5/16 X .625, Push Nut, GR 5, Zinc/Clear (Was 1921982, 3031796 or 80003523)
0030-30 7012312YP 2 BEARING, 9/16” ID
0030-50 7032722YP 1 ARM, Wheel, Right Rear, Zinc/Clear
0030-60 7035717YP 2 LATCH, Height Adjusting, (long)
0030-70 703967 6 SCREW, #10-32 x 3/8, Torx Hex Washer Head Self-Tap, ZC/CL (Was 7091012 or 80005604)
0030-90 7103793YP 4 GRIP, Height Latch, Black (Was 7100633)
0040 7054247YP 1 ASSEMBLY, Wheel Arm, Left Rear, Long (Was 7054231YP)
0040-50 7032723YP 1 ARM, Wheel, Left Rear, Zinc/Clear
0050 703348 4 NUT, 7/16-20, Hex Jam Center Lock, GR B, Zinc/Clear (Was 7090377 or 80004407)
0060 690272MA 4 NUT, 5/16-18, Serated Lock F lange, GR5, Zinc/Clear (Was 7091601 or 80002728)
0070 7021119YP 1 AXLE, V21
0080 7031960YP 2 HUBCAP, Rear
0090 7031121YP 4 HUBCAP, Front
0100 7600179YP 1 ASSEMBLY, Front Wheel Arm, LH (Was 7051885)
0100-50 7031016YP 1 WHEEL ARM, L.H. Front (Square Hole)
0110 7035727YP 2 WHEEL, 8 x 1.75 - Steel - D - Gray

---- 7011125YP 4 BEARING, 7/16” ID, Ball, Front Wheel (Not Shown)
0120 7035726YP 2 WHEEL, 10 x 1.75, Steel-D, (Self Propelled) - Gray

Footnotes:

SERIES 20

Manual No.

9

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Deck, Engine & Blade Group

Manual No.

7106167 22" STEEL DECK WALK BEHIND

10

SERIES 20

Not for

Reproduction

Deck, Engine & Blade Group

Part No DescriptionItem Qty

0010 703299 2 SCREW, 5/16-24 X 1.25, Hex Head Cap, GR5, Zinc/Clear (Was 1921982, 3031796 or

80003523)
0020 7010783YP 1 KEY, HI-PRO, #505
0030 703297 2 RETAINER, 5/16 X .625, Push Nut, GR 5, Zinc/Clear (Was 028X64MA, 5025498, 7011791,

720372 or 80002734)
0040 703963 1 WASHER, 13/32x1-13/32” Dia. Cone (Was 7012063 & 80005590)
0050 7012927YP 1 HUB, Blade, 7/8” ID
0060 7021822YP 1 PULLEY, Engine, 1” ID X 2-1/8” OD , Yellow
0070 7024340SM 1 SPACER, .375 OD X .316 ID X .305 L
0080 7026691YP 1 BLADE, 21” L, .97” Standard Lift
0090 7044770YP 3 SPACER, .874 OD X .385 ID X .060 L, YZ
0100 7046780SM 2 PLUG, Hole, .44” OD, Polyethylene
0110 7074568YP 1 COVER, Belt, Zinc/Clear
0120 703999 1 SCREW, 3/8-24 X 2, Hex Head Cap, GR5 (W as 7090167 or 80005591)
0130 704002 1 BOLT, 5/16-18 X 1.125, Carriage, ZC/CL (Was 7091169 or 80005594)
0140 704001 1 NUT, 5/16-18 Large Flange Cente r Loc k , ZC/CL (Was 7090951 or 80005593)
0150 703116 2 WASHER, .32 X .58 X .08, Split Lock, Zinc/Clear (Was 7091315 or 80002745)
0160 703185 2 BOLT, 5/16-18 x 3/4, Carriage, Short Neck, G5, Zinc/Clear (Was 7091508 or 80004072)
0170 690272MA 4 NUT, 5/16-18, Serated Lock F lange, GR5, Zinc/Clear (Was 7091601 or 80002728)
0180 704062 1 BOLT, 5/16- 18 X 2.0, Serrated Flanged Head, ZC/CL (Was 7091592 or 80005974)
0190 704003 1 SCREW, 5/16-18 X .50, Hex Socket Head, Phosp/Oil (Was 7092086 or 80005595)
0200 7102407YP 1 * ENGINE, 5.5 GTP Honda Comm Tier III, Model GXV160UH2A1AS Code 649061
0210 7300969BMYP 1 RING, Engine Spacer
0220 7500549DYP 1 WELDMENT, Deck, 21”, Self-Propell, HV (Was 7400027DYP)
0230 7075305YP 1 GRIP, Standoff
0240 7075306YP 1 STANDOFF
0250 703447 2 BOLT, 5/16- 18 X .625, Carriage, GR5, Zinc/Clear (Was 1931332, 703125, 7090799, 7091026 or

80003584)

Footnotes:

NOTE: * Purchase engine parts from engine manufacturer dealer.

SERIES 20

11

Manual No.

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Drive System, Self Propelled

Manual No.

7106167 22" STEEL DECK WALK BEHIND

12

SERIES 20

Not for

Reproduction

Drive System, Self Propelle

d

Part No DescriptionItem Qty

1 1753983YP 1 SCREW, 5/16-18 x 5/8 Truss Head Torx
2 7090391SM 1 WASHER, 5/16, Internal Lock, Zinc/Clear (Was 80003683)
3 7034179BMYP 1 LINK, Differential, Commercial
4 703940 1 WASHER, 0.445 ID X 0.780 OD X 0.025 Thk, Wave, ZC/CL (Was 7011724 or 80005390)
5 7012354YP 1 BELT, Poly-V
6 703127 1 NUT, 1/4-20, G5 Zinc/Clear (Was 7090063, 7091576 or 80003586)
7 703462 2 WASHER, 1/4 Internal Tooth Lock, YZ (Was 7090053 or 80004414)
8 7012616YP 1 SUPPORT, Foot Guard
9 703978 1 BOLT, 1/4-20 X 1/2, Carriage, GR5 YZ (Was 7090005, 7091604 or 80004564)
10 7029008YP 1 GUARD, Rear Foot, 21”
11 704009 1 RING, Split, .68 x .93 x .44 (Black) (Was 7023791 or 80005645)
12 703458 1 NUT, 3/8-24 Hex Center Lock, GR B, YZ (Was 7090289 or 80004409)
13 B4300GS 2 SCREW, 1/4-20 X .500, Hex HD, Self-Tap, Zinc/Clear (Was 1925003, 704130, 7090539,

7091122, 720041 & 80002738)
14 7031809YP 1 HOLDER, Bearing (Outer Half), ZC/CL
15 704008 1 O-RING, 1.0 ID X 1.25 OD X 0.125 Thk (Was 7011025 or 80005646)
16 7028014YP 1 BALL BEARING, Spherical O.D., .38 I.D.
17 7031873YP 1 HOLDER, Bearing (Inner Half)
18 703946 1 WASHER, .390 ID X .720 OD X .054 Thk, Flat, ZC/CL (Was 7012316 or 80005532)
19 7019383YP 1 PULLEY, Poly-V, 2.0” OD, Steel
20 703895 2 NUT, 3/8-24, Hex, GR 5, Zinc/Clear (Was 7091630 or 80004865)
21 703930 3 WASHER, 3/8” Internal Tooth Lock,Type A, ZC/CL (Was 7090390 or 80005380)
22 703836 1 STUD, 3/8-24 X 2.38, Single End, ZC/CL (Was 7012111 or 80004419)
23 7012126YP 1 SPRING, Idler Torsion
24 703828 1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap, Grade 5, CZ/CL (Was 7091025 or 80004836)
25 7012124YP 1 PULLEY, Flat Idler, .25 ID, 2.25 OD
26 703972 1 NUT, 1/4-28 Hex Top Lock, GR 5, BZ (Was 7090303 or 80005377)
27 7012122YP 1 SPRING, Clutch
28 331613MA 1 PIN, 3/32 X 3/4, GR5, Cotter, Zinc/Clear (Was 1918447, 703312, 7090555, 7091597 or

80002736)
29 7072284YP 1 SHAFT, Hex (3/8-24 thread, one end)
30 704060 7 SCREW, #10-24 x 1/2” Hex Washer Self-Tap, Torx, ZC/CL (Was 7090913 or 80005972)
31 7031013YP 1 PLATE, Driven Tire Side
32 704059 1 Disc, Rubber Driven, 3” ID (Was 7010927, 7023364 or 80005971)
33 703837 1 STUD, 3/8-24 X 4.5, Plate, ZC/CL (Was 7012125 or 80004420)
34 704061 4 SCREW, #10-32 X 1/4,Hex Washer, Self-Tap, ZC/CL (Was 7090981 or 80005973)
35 7029027YP 1 BEARING, 3/4” ID, Ball, Commercial
36 7300977BMYP 1 THRUST PLATE, Short, Black
37 703975 1 RETAINING RING, 3/4” ID, ZC/CL (Was 7010746 or 80005391)
38 703590 1 WASHER, 3/8 (.406 X .816 X .65), Flat, Zinc/Clear (Was 7090122, 71072MA or 80003536)
39 703461 2 NUT, 1/4-28 Hex, GR5, Zinc/Clear (Was 7090095 or 80004412)
40 703332 2 WASHER, 1/4, Flat, GR5 Zinc/Clear (Was 1921319, 7022473, 5025154, 7091294) or 80002742)
41 7015753YP 2 BALL JOINT, 1/4-28
42 7074145YP 1 LINK, Transfer (1/4-28 thread)
43 703464 1 PIN, 1/16 X 0.50 Cotter, GR 5 Zinc/Clear (Was 1501125MA, 579493MA, 7090673, 7091629,

724605 or 80003540)

Footnotes:

SERIES 20

13

Manual No.

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Drive System, Self Propelled

Manual No.

7106167 22" STEEL DECK WALK BEHIND

14

SERIES 20

Not for

Reproduction

Drive System, Self Propelle

d

Part No DescriptionItem Qty

44 7046784YP 1 BELT, Engine Drive (Stretch)
45 7073528YP 1 DRIVE DISC, Steel
46 703971 1 BUSHING, 0.385 ID X 0.925 OD X 1.018 Thk, ZC/CL (Was 7017696 or 80005376)
47 690272MA 6 NUT, 5/16-18, Serated Lock Flange, GR5, Zinc/Clear (Was 7091601 or 80002728)
48 7029025YP 1 SPRING, Extension, .58 x 3.2
49 703798 2 BOLT, 5/16-18 X .50, Carriage, Zinc/Clear (Was 7090731, 725993, 908156MA or 80004563)
50 703447 1 BOLT, 5/16-18 X .625, Carriage, GR5, Zinc/Clear (Was 1931332, 703125, 7090799, 7091026 or

80003584)
51 703297 2 RETAINER, 5/16 X .625, Push Nut, GR 5, Zinc/Clear (Was 028X64MA, 5025498, 7011791,

720372 or 80002734)
52 703457 1 NUT, 3/8-16, Hex, GR 5, Zinc/Clear (Was 7091302 or 80004413)
53 7052987BMYP 1 ASSEMBLY, Deck Bracket, P21S
54 7033774YP 1 BRACKET, Deck, P21S
55 703941 1 SPACER, .50 ID X .650 OD X 1.750, Thk, ZC/CL (Was 7021758 or 80005392)
56 703973 2 BUSHING, Flanged, .381 x .625 x .62, Metal, CZ/CL (Was 7012306 or 80005378)
57 7600173YP 1 ASSEMBLY, Idler Arm, Bushing & Spacer (Was 7500154BMYP)
58 7032832AYP 1 ARM, Clutch Idler
59 703974 1 SPACER, Idler Arm (.500 ID x .970 Long), ZC/CL (Was 7100447 or 80005379)
61 7051913YP 1 ASSEMBLY, Clutch Idler
62 7061275YP 1 ASSEMBLY, Drive Disc, Square, P21S (Was 7053263YP)
63 7061276YP 1 KIT, Bushing & Hub Assembly (Was 7053217)
64 ---- 1 HUB, Driven Disc, USE 7061276YP
65 7011108YP 1 BUSHING, Hex Drive, 1.2”, .75” OD, .512” ID, Black Nylon
66 7600109YP 1 KIT, Driven Disc Assembly (Was 7501000)

Footnotes:

SERIES 20

15

Manual No.

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Transmission - Differential Group

Manual No.

7106167 22" STEEL DECK WALK BEHIND

16

SERIES 20

Not for

Reproduction

Transmission - Differential Group

Part No DescriptionItem Qty

0010 7011110YP 4 SHAFT, Pinion
0040 7011774YP 1 GASKET, Housing
0050 7012495YP 1 GEAR, Differential, 46 Tooth
0060 703933 4 SPACER, .700 OD x .480 ID x .3 80 L, Z C/CL (Was 7012500 or 80005383)
0080 7019213YP 1 PULLEY, Poly-V Belt (3.5 O.D.)
0090 7021115YP 4 GEAR, Pinion (12 Tooth)
0100 7031965YP 2 WASHER, 1.25 X .765 X .03, Thrust, ZC/CL (Was 80003519)
0110 7031970YP 2 PLATE, Differential Gear, V21
0120 7050767YP 1 ASSEMBLY, Input Gear
0130 7051903AYP 1 WELDMENT, Differential Bracket
0140 7053943YP 1 ASSEMBLY, Transmission
0140-10 703934 1 SPACER, .820 OD X .720 ID X .330 L, ZC/CL (Was 7012543 or 80005384)
0140-20 7050830YP 1 ASSEMBLY, Short Axle (Was 7051932)
0140-30 7050831YP 1 ASSEMBLY, Long Axle (Was 7051933)
0150 7053939YP 1 ASSEMBLY, Left Housing (Was 7053938)
0150-10 7012314YP 2 SEAL, 5/8” ID
0150-20 7029033YP 1 HOUSING, Left Hand
0150-30 7029035YP 2 BEARING, Tapered, Differential Housing
0160 7051908YP 1 ASSEMBLY, Housing, Right Hand (Was 7053941)
0160-30 703935 3 BOLT, 5/16-24 x 1-1/8” Rib Neck, GR 5, ZC/BK (Was 7014155 or 80005385)
0160-40 7024442YP 3 GASKET, 5/8” O.D.
0160-50 7029034YP 1 HOUSING, Right Hand
0160-70 7073963YP 1 BEARING, Ball, 1.125 OD, .440 ID, 3.8 Wide
0170 703936 3 WASHER, .325 ID X .850 OD X .041 Th k, Internal External Lock, Type A, ZC/CL (Was 7090189

or 80005386)
0180 703937 4 NUT, #10-32 Nyloc, GR A, ZC/CL (Was 7090376 or 80005387)
0190 703938 4 SCREW, #10-32 x 1-1/2 Hex Head Cap GR5, Z C/CL (Was 7090557 or 80005388)
0210 703349 1 WASHER, .453 X .75 X .073, Flat, ZC/CL (Was 7091720 or 80004406)
0220 703459 4 NUT, 5/16-24, Hex Crown Lock,GR C, Zinc/Clear (Was 7092062 or 80004410)
0230 703939 1 WASHER, .32 ID x 1.40 OD x .1 0 Thk, Bellville, ZC/CL (W as 7092063 or 80005389)
0240 703833 4 SCREW, 1/4-20 x 1 Hex Washer Self-Tap, ZC/CL (Was 7091825, 7092064 or 80004415)
0250 703931 1 PLUG, T r ansmission Housing (Was 7016544 or 80005381)
0260 7061017 GREASE, “OO” (4 oz max) (Not Shown)

Footnotes:

SERIES 20

17

Manual No.

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Grass Bag & Adapter Group

Manual No.

7106167 22" STEEL DECK WALK BEHIND

18

SERIES 20

Not for

Reproduction

Grass Bag & Adapter Group

Part No DescriptionItem Qty

1 ---- 1 USE 7600176 Grass Bag Assembly, W/Slider, 10.75” W, 26” L, No Graphics (Was 7103205)
2 7050711YP 1 ASSEMBLY, Slider
3 7042489AYP 1 WELDMENT, Bag Connector
4 7019247YP 1 WIRE, Rear Bag
5 7600117YP 1 KIT, Bag Adapter Assembly, W/pulley (Includes items 6 - 13) (Was 7058037)
6 ---- 1 USE 7600117, Bag Adapter (Was 7047081)
7 7047082AYP 1 BRACKET, Rope Pulley
8 703570 1 SCREW, 5/16-18 X 1.25, Torx Pan Head, GR 5, Zinc/Clear (Was 7091984 or 80004616)
9 703973 1 BUSHING, Flanged, .381 x .625 x .62, Metal, CZ/CL (Was 7012306 or 80005378)
10 7024228SM 1 PULLEY, Nylon, .75 ID, 1.3 OD
11 690272MA 1 NUT, 5/16-18, Serated Lock Flange, GR5, Zinc/Clear (Was 7091601 or 80002728)
12 703942 3 WASHER, 5/32 Flat, ZC/CL (Was 7072107 or 80005393)
13 704032 3 RIVET, 3/16 x .344, Truss HD, ZC/CL (Was 7013860 or 80005709)
14 7024340SM 1 SPACER, .375 OD X .316 ID X .305 L
15 7101022YP 2 KNOB, Fluted (5/16-18 thread) on side chute
16 703297 2 RETAINER, 5/16 X .625, Push Nut, GR 5, Zinc/Clear (Was 028X64MA, 5025498, 7011791,

720372 or 80002734)
17 703936 2 WASHER, .325 ID X .850 OD X .041 Thk, Internal External Lock, Type A, ZC/CL (Was 7090189

or 80005386)
17 703350 1 WASHER, 5/16, Flat SAE, Zinc/Clear (Was 7091076, 7091088 or 80004405)
18 704001 1 NUT, 5/16-18 Large Flange Center Lock, ZC/CL (Was 7090951 or 80005593)
19 703185 2 BOLT, 5/16-18 x 3/4, Carriage, Short Neck, G5, Zinc/Clear (Was 7091508 or 80004072)

Footnotes:

SERIES 20

19

Manual No.

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Decal Group

Manual No.

7106167 22" STEEL DECK WALK BEHIND

20

SERIES 20

Not for

Reproduction

Part No DescriptionItem Qty

0010 7075471YP 1 DECAL, Speed Shift
0020 7102324YP 1 DECAL, Chute / Deflector FC
0030 7100984YP 1 DECAL, Warning / Dang er
0040 7105261YP 1 DECAL, CPSC, French/Engli sh
0050 7104148YP 1 DECAL, Logo, Snapper, 7.88”
0060 7029782MA 1 DECAL, OPC Bail, International Symbols
0070 7075524YP 1 DECAL, Throttle Control, KWV
0080 7101497YP 1 DECAL, Warning / Dang er, French /English
0090 7102746YP 1 DECAL, Spark Arrestor
0100 7102996YP 1 DECAL, ICES Compliance
0110 7104873YP 1 DECAL, Commercial, 5.35”
0500 7106039YP 1 DECAL, Spark Arrestor, French

Decal Group

Footnotes:

SERIES 20

21

Manual No.

710616722" STEEL DECK WALK BEHIND

Not for

Reproduction

Not for

Reproduction

Not for

Reproduction

Parts Manual fo

r

22" STEEL DECK WALK BEHIND
COMMERCIAL MOWER
SERIES 20

IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS

PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.

WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD

IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY

OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS

Briggs & Stratton Yard Power Products Group

535 Macon Road
McDonough, GA, 30253 U.S.A.
800-935-2967

www.snapper.com

Copyright ©
Milwaukee, WI USA. All Rights Reserved

Briggs & Stratton Corporation

2013

Manual No.

Revision: - 9/30/2013

7106167