Page 1
1
Installation
Instructions
Sub-Frame Hitch
Mfg. No. 1695196
For Prestige / 1800 / 2800, Conquest / 1700 / 2700, &
Broadmoor / 1600 / 2600 Series Tractors
This kit is required when installing front mounted
snowthrowers.
Page 2
2
Installation Instructions Sub-Frame Hitch
Early Manual
Lift Only
(See Instructions)
Hydraulic
Lift
47
16
28
27
25
33
40
41
39
38
37
36
43
51
42
33
25
29
29
29
28
28
27
50
17
13
11
14
9
12
13
11
19
18
21
20
10
24
23
7
8
9
9
22
15
9
25
49
22
31
30
30
25
27
28
27
33
25
34
32
3
2
1
4
5
6
33
25
28
27
25
26
27
28
35
Front Hole for Dozer Applications
Rear Hole for Snowthrower Applications
45
46
48
Main Hitch Components (All Applications)
Figure 1. Contents
Page 3
3
Sub-Frame Hitch Installation Instructions
Ref Part No. Qty. Description
1 1723292A 1 SHAFT & HOOK ASSY
2 1653768A 1 CLAMP, Support
3 1931335 4 CARRIAGE BOLT, 5/16-18 x 1
4 1919381 4 WASHER, 11/32
5 1917356 3 LOCKWASHER, 5/16
6 1917372 4 NUT, 5/16-18
7 105249 1 PIN, Round Head, 3/8 x 2-3/8
8 1724025 1 LIFT LEVER ASSY.
9 2176012 4 SAFETY CLIP
10 1722946 1 LIFT ROD
11 8031007 2 SET COLLAR
12 2171011 1 SPRING, Compression
13 1928721 2 SET SCREW, 5/16-18 x 1/2
14 1723115 1 ROD GUIDE
15 1733812 2 ROD, Hitch
16 1733309 1 ROD, Hitch
17 1733779A 1 HITCH ASSY.
18 1722819 1 PIN, Headless, 1/2 x 2
19 1723795A 1 BAR, Lift Link
20 1960033 1 HAIR PIN CLIP
21 1722469 1 PLATE, Lock, Hydraulic Lift
22 1667811 1 SPACER
23 1960244 1 SCREW, Whiz, 3/8-16 x 2-3/4
24 1921971 1 CAPSCREW, 3/8-16 x 3/4
25 1922755 8 WASHER PLAIN, 3/8
26 2162115 1 BELT GUIDE
27 1916965 7 LOCKWASHER, 3/8
28 1916950 6 NUT HEX FULL, 3/8-16
29 2171247 1 PULLEY-FLAT
30 1666287 1 PULLEY ASS'Y
31 1666294 1 SPACER-BRG
32 1922130 2 CAPSCREW, 3/8-16 x 2
33 158227 4 SPACER
34 1921971 1 CAPSCREW, 3/8-16 x 1-3/4
35 1722963 1 PIVOT BRACKET
36 1930651 1 NUT LOCK, 3/8-16
37 1704743 1 TRUNNION
38 1668282 1 SPRING
39 1722972 1 GUIDE ASS'Y -SPRING
40 1960268 1 CARRIAGE BOLT, 3/8-16 x 1-1/4
41 1723681 1 ROD ASS'Y
42 1703371 1 V-BELT, Single-Stage Blower
42 1703372 1 V-BELT, Two-Stage Blower
43 1701600 2 REFLECTOR
44 1922130 1 CAPSCREW, 3/8-16 x 2-1/4
45 1733814A 1 PUSH BAR LATCH
46 1960074 2 CLIP
47 1921210 4 BOLT, .38-16 x 1
48 1928352 4 NUT- FLG, .38-16
49 1724387 1 PULLY-FLAT
50 1677135A 1 BELT GUIDE
51 1922130 1 CAPSCREW, 3/8-16 x 2-1/4
52 1667812 1 SPACER
Page 4
4
Installation Instructions Sub-Frame Hitch
Figure 2. Install Support Clamp
A. 5/16-18 x 1 Carriage Bolt D. 11/32 Washer
B. Hook Assembly E. 5/16 Lockwasher
C. Support Clamp F. 5/16-18 Nut
B
C
D
E
A
F
Figure 4. Assemble Lift Rod
A. Lift Rod C. Spring
B. Set Collar D. Rod Guide
B
C
D
B
A
NOTE: Please read through these instructions and the
instructions of any other attachments before beginning
installation.
INITIAL ASSEMBLY
Assemble Hitch
1. Attach the support clamp (C, Figure 2) and hook
assembly (B) to the hitch. Secure with four 5/16-18 x
1 carriage bolts (A), washers (D), lockwashers (E),
and nuts (F). Do not tighten the hardware at this
time.
WARNING
Before beginning any service work turn off the
PTO, set the parking brake, turn off the ignition,
and disconnect the spark plug wire(s).
Figure 5. Early/Later Lift Links
A. Early Model Lift Link
B. Later Model Lift Link
A
B
Conquest / 1700 /
2700 &
Prestige / 1800 /
2800 Series
B
C
D
E
A
F
Broadmoor /
1600 / 2600
Series
Assemble Push Bar Latch
1. Attach Push Bar Latch (B, Figure 3), to hitch. Secure
with four .31-16 x 1 bolts (A), and four .38-16 flange
nuts (C).
T wo Wheel
Drive Models
Four Wheel
Drive Models
A
B
C
Figure 3. Assemble Push Bar Latch
A. Bolt, .38-16 x 1 C. Flange Nut, .38-16
B. Push Bar Latch
Assemble Lift Rod
1. Install the set collars (B, Figure 4), spring (C), and
rod guide (D) on the lift rod (A) as shown. Final
adjustment of the set collars will be made after the
hitch and attachment are installed.
Page 5
5
Sub-Frame Hitch Installation Instructions
INITIAL INSTALLATION
Manual Lift Models
LIFT LINK - EARLY VS. LATER
The early model lift link (A, Figure 5) was used on early
production Conquest/1700/2700 Series tractors. It must
be replaced with the later model lift link (B) included with
this attachment. The later model link works in all applications. Discard the early model link (A).
LIFT LINK POSITION
The lift link is installed differently depending on what
attachment is being used. Refer to Figure 6 for link
installation information.
Hydraulic Lift Models
1. Fully lower the hydraulic lift. The lift assembly is
spring loaded so it will need to be held in the down
position to perform of the following procedures.
2. Remove and retain the flat head pin (B, Figure 7) and
hair pin clip (E) securing the lift cylinder (A) to the lift
shaft assembly (F). Remove and retain the flat washers.
3. Mount the lock plate (D) next to the cams on the lift
shaft assembly (F) as shown.
4. Install the original flat head pin (B) and new flat head
pin (C) and secure with hair pin clips.
A
B
C
D
E
A
F
C
D
G
Figure 6. Connect Lift Link
A. Pin
B. Rear Hole of Lift Bar (Snowthrower Applications)
C. Spacer
D. Hair Pin Clip
E. Upper Hole (Snowthrower Applications)
F. Slot of Lift Link (Mower Applications)
G. Lower Hole (Mower Applications)
Snowthrower
& Dozer
Applications
Mower
Applications
Figure 7. Install Lock Plate - Hydraulic Lift Models
A. Lift Cylinder D. Lock Plate
B. Flat Head Pin (Original) E. Hair Pin Clips
C. Flat Head Pin (New) F. Lift Shaft Assy.
A
B
C
D
F
E
Page 6
6
Installation Instructions Sub-Frame Hitch
A
C
D
E
B
Figure 8. Install Hitch
A. J-Hooks D. Hook
B. Hitch Rod E. Clamp Plate
C. Hitch Rod
Install Hitch
1. Slide the hitch under the tractor.
2. Raise the rear of the hitch and place the hook (C)
over the lift shaft.
3. Connect the front of the hitch to the tractor J-hooks
(A, Figure 8) using the hitch rod (B) and a safety clip
in the top holes of the push bar latch.
4. Secure the front of the hitch to the tractor by attaching the hitch rod (C) and a safety clip in the bottom
holes of the push bar latch.
5. Push the clamp plate (D) backwards until it is snug
against the lift shaft. Tighten the clamp plate hardware (E).
Page 7
7
Sub-Frame Hitch Installation Instructions
Install Lift Rod
1. Slide the lift lever (A, Figure 9) onto the end of the
tractor lift shaft (B) under the right side footrest.
2. Use the tabs on the lift lever (A) to capture the tractor
lift arm. Secure in place with a clevis pin (D) and
safety clip (C).
3. Insert the rear of the lift rod (B, Figure 10) into the
bottom of the lift lever (A). Secure with a clip (C).
Install Reflectors
1. Install the two reflectors on the rear of the tractor seat
deck.
Figure 9. Install Lift Lever
A. Lift Lever
B. Lift Shaft
C. Safety Clip
D. Clevis Pin
Figure 10. Install Lift Rod - All Models
A. Lift Lever
B. Lift Rod
C. Clip
A
C
B
D
A
C
B
Page 8
Installation Instructions Sub-Frame Hitch
REMOVAL
NOTE: After removing components, reinstall the clevis
pins and clips to prevent loss.
1. Disconnect the lift rod from the attachment and lift
lever extension (C, Figure 11).
2. Remove the clevis pin and clip from the lift lever (C)
and remove the lift lever.
3. Remove the front hitch rod (A) and (B). Remove the
hitch and hook (F).
4. Remove the lock plate (E) OR reposition the lift link
(D) in mowing position.
NORMAL INSTALLATION
1. Insert the hook (F, Figure 11) into the back of the
hitch. Mount the rear of the hitch on the lift crossshaft.
2. Secure the front of the hitch to the J-hooks using the
hitch rod (A) and (B) (Figure 8).
3. Install the downward pressure lock plate (E) OR
place the lift link (D) in snowthrower position.
4. Install the lift lever extension (C).
5. Install the lift rod and attachment (Figure 10).
Figure 11. Normal Installation & Removal
B
C
D
E
F
A. Hitch Rod
B. Hitch Rod
C. Lift Lever Extension
D. Lift Link (Manual)
E. Pressure Lock Plate
(Hydraulic)
F. Hook
Snowthrower
Position
A
8
Page 9
9
Sub-Frame Hitch Installation Instructions
A
F
C
D
G
Figure 13. Lift Link - Manual Lift Models
A. Pin
B. Rear Hole of Lift Bar (Snowthrower Applications)
C. Spacer
D. Hair Pin Clip
E. Upper Hole (Snowthrower Applications)
F. Slot of Lift Link (Mower Applications)
G. Lower Hole (Mower Applications)
A
B
C
D
E
Snowthrower
& Dozer
Applications
Mower
Applications
Figure 12. Lift Lock Plate - Hydraulic Lift Models
A. Lift Cylinder
B. Flat Head Pin (Original)
C. Flat Head Pin (New)
D. Lock Plate
E. Hair Pin Clips
F. Lift Shaft Assy.
G. Washers
A
B
C
D
F
E
A
B
F
G
E
LIFT V ARIA TIONS WHEN USING
ATTACHMENTS
When a front-mounted attachment such as a snowthrower or dozer blade is used with the tractor, the lift mechanism must be locked to provide downward force. When
the mower is reinstalled the downward pressure lock
must be released so that the mower can float.
Hydraulic Lift Models
When using a snowthrower or dozer, the downward
pressure lock plate (D, Figure 12) and an additional pin
(C) is installed. These parts are included with the attachment. Note that the washers (G) are not used with the
lock plate.
When mowing, the downward pressure lock plate (D) is
removed and replaced with two washers (G). The additional pin (C) is also removed.
Fully lower the hydraulic lift. The lift assembly is spring
loaded so it will need to be held in the down position to
perform of the following procedures.
Manual Lift Models
NOTE: These instructions apply to Conquest / 1700 /
2700 Series tractors or Broadmoor / 1600 / 2600 Series
tractors equipped with a lift lever kit.
The lift link is installed differently depending on what
attachment is being used. Refer to Figure 13 for link
installation information.
Snowthrower
& Dozer
Applications
Mower
Applications
Page 10
Installation Instructions Sub-Frame Hitch
Form No. 1733911-04
Rev. 01/2007
© 2007 Briggs & Stratton, Inc. All Rights Reserved
TP 200-4417-04-AT-SMAN
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
NOTES
Loading...