Briggs & Stratton 150Z User Manual
OPERATOR’S
MANUAL
24HP Zero-Turn Riders
Mfg. No. Description
2690644 Simplicity Axion, 24HP w/ 50” Mower
2690647 Snapper 150Z, 24HP w/ 50” Mower
2690771 Simplicity Axion, 24HP w/50” Mower (AUST)
Axion / 150Z Series
1734393
Revision 01
Rev. Date 10/2007
TP 100-4471-01-ZT-SN
1
TABLE OF CONTENTS
Safety Rules
General Operation...................................................2
Transportation & Storage ........................................2
Slope Operation ......................................................3
Towed Equipment....................................................3
Children...................................................................3
Emissions................................................................3
Ignition System .......................................................3
Slope Sighting Guide ..............................................4
Service & Maintenance ...........................................5
Safety & Operation Decals..........................................6
Identification Numbers................................................7
Operation
Control Functions....................................................8
General Operating Safety .......................................9
Checks before Starting..........................................10
Fuel Recommendations ........................................10
Emergency Stopping.............................................11
Stopping the Rider and Engine .............................11
Starting the Engine ...............................................11
Mowing..................................................................11
Pushing the Rider by Hand ...................................11
Driving Practice.....................................................12
Mower Deck Removal & Installation......................14
Maintenance
Maintenance Schedule .........................................14
Rider Maintenance
Accessing the Engine Compartment.....................16
Clean Debris from Rider and Engine ....................16
Clean Debris from Engine Cooling Areas .............16
Check Tire Pressure..............................................16
Lubrication ............................................................17
Clean Deck & Check/Replace Mower Blades.......18
Clean the Battery & Cables...................................19
Check Rider Safety System ..................................19
Check/Adjust PTO Clutch......................................20
Engine Maintenance
Check Engine Oil Level .........................................21
Change Engine Oil................................................21
Change Engine Oil & Filter ...................................21
Service Air Filter & Pre-Cleaner............................22
Replace Spark Plug ..............................................23
Service & Adjustments
Ground Speed Control Lever Adjustment .............24
Speed Balancing Adjustment................................24
Cutting Height Adjustment ....................................24
PTO Clutch Adjustment.........................................24
Brake Adjustment..................................................25
Battery Charging ...................................................25
Engine Adjustments ..............................................25
Mower Deck Leveling Adjustments .......................26
Mower Belt Replacement......................................27
Storage..................................................................28
Troubleshooting
Troubleshooting the Rider - Chart .........................29
Troubleshooting the Mower - Chart .......................30
Specifications ............................................................31
Service Items .............................................................31
Lawn Care ..............................................................LC-1
NOTE: In this manual, “left” and “right” are referred to as seen from the operating position.
2
SAFETY RULES
GENERAL OPERATION
1. Read, understand, and follow all instructions in the
manual and on the unit before starting.
2. Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at
all times.
3. Only allow responsible adults, who are familiar with
the instructions, to operate the unit (local regulations
can restrict operator age).
4. Clear the area of objects such as rocks, toys, wire,
etc., which could be picked up and thrown by the
blade(s).
5. Be sure the area is clear of other people before
mowing. Stop the unit if anyone enters the area.
6. Never carry passengers.
7. Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while
travelling in reverse.
8. Never direct discharge material toward anyone. Avoid
discharging material against a wall or obstruction.
Material may ricochet back toward the operator. Stop
the blade(s) when crossing gravel surfaces.
9. Do not operate the machine without the entire grass
catcher, discharge guard (deflector), or other safety
devices in place and operational.
10. Slow down before turning.
11. Never leave a running unit unattended. Always
disengage the blades (PTO), set parking brake, stop
engine, and remove keys before dismounting.
12. Disengage blades (PTO) when not mowing. Shut off
engine and wait for all parts to come to a complete
stop before cleaning the machine, removing the grass
catcher, or unclogging the discharge guard.
13. Operate the machine only in daylight or good artificial
light.
14. Do not operate the unit while under the influence of
alcohol or drugs.
15 Watch for traffic when operating near or crossing
roadways.
16. Use extra care when loading or unloading the unit
into a trailer or truck.
17. Always wear eye protection when operating this unit.
18. Data indicates that operators, age 60 years and
above, are involved in a large percentage of power
equipment-related injuries. These operators should
evaluate their ability to operate the equipment safely
enough to protect themselves and others from injury.
19. Follow the manufacturer’s recommendations for wheel
weights or counterweights.
20. Keep in mind the operator is responsible for accidents
occurring to other people or property.
21. All drivers should seek and obtain professional and
practical instruction.
22. Always wear substantial footwear and trousers.
Never operate when barefoot or wearing sandals.
23. Before using, always visually check that the blades
and blade hardware are present, intact, and secure.
Replace worn or damaged parts.
24. Disengage attachments before: refueling, removing
an attachment, making adjustments (unless the
adjustment can be made from the operator’s
position).
25. When the machine is parked, stored, or left
unattended, lower the cutting means unless a positive
mechanical lock is used.
26. Before leaving the operator’s position for any reason,
engage the parking brake, disengage the blades
(PTO), stop the engine, and remove the key.
27. To reduce fire hazard, keep the unit free of grass,
leaves, & excess oil. Do not stop or park over dry
leaves, grass, or combustible materials.
28. It is a violation of California Public Resource Code
Section 4442 to use or operate the engine on or near
any forest-covered, brush-covered, or grass-covered
land unless the exhaust system is equipped with a
spark arrester meeting any applicable local or state
laws. Other states or federal areas may have similar
laws.
29. OSHA regulations may require the use of hearing
protection when exposed to sound levels greater than
85 dBA for an 8 hour time period.
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control
of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
This mowing deck is capable of amputating hands and feet and throwing objects.
The triangle in text signifies important cautions or warnings which must be followed.
TRANSPORTING AND STORAGE
1. When transporting the unit on an open trailer, make
sure it is facing forward, in the direction of travel. If
the unit is facing backwards, wind lift could damage
the unit.
2. Always observe safe refueling and fuel handling
practices when refueling the unit after transportation
or storage.
3. Never store the unit (with fuel) in an enclosed poorly
ventilated structure. Fuel vapors can travel to an
ignition source (such as a furnace, water heater, etc.)
and cause an explosion. Fuel vapor is also toxic to
humans and animals.
4. Never store the unit or fuel container inside where
there is an open flame or pilot light, such as near a
water heater. Allow unit to cool before storing.
CAUTION
This machine produces sound levels in
excess of 85 dBA at the operator’s ear and
can cause hearing loss though extended
periods of exposure.
Wear hearing protection when operating this
machine.
3
CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the unit
and the mowing activity. Never assume that children will
remain where you last saw them.
1. Keep children out of the mowing area and under the
watchful care of another responsible adult.
2. Be alert and turn unit off if children enter the area.
3. Before and during reverse operation, look behind and
down for small children.
4. Never carry children, even with the blade(s) off. They
may fall off and be seriously injured or interfere with
safe unit operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
5. Never allow children to operate the unit.
6. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
EMISSIONS
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth
defects, or other reproductive harm.
2. Look for the relevant Emissions Durability Period and
Air Index information on the engine emissions label.
IGNITION SYSTEM
1. This spark ignition system complies with Canadian
ICES-002.
SLOPE OPERATION
Slopes are a major factor related to loss-of-control and tipover accidents, which can result in severe injury or death.
Operation on all slopes requires extra caution. If you cannot
back up the slope or if you feel uneasy on it, do not operate
on it.
Control of a walk-behind or ride-on machine sliding on a
slope will not be regained by the application of the brake.
The main reasons for loss of control are: insufficient tire
grip on the ground, speed too fast, inadequate braking, the
type of machine is unsuitable for its task, lack of awareness
of the ground conditions, incorrect hitching and load
distribution.
1. Mow up and down the face of slopes, not across.
2. Watch for holes, ruts, or bumps. Uneven terrain could
overturn the unit. Tall grass can hide obstacles.
3. Choose a slow speed so that you will not have to stop
or change speeds while on the slope.
4. Do not mow on wet grass. Tires may loose traction.
5. Avoid starting, stopping, or turning on a slope. If tires
lose traction (i.e. machine stops forward motion on a
slope), disengage the blade(s) (PTO) and drive slow
off the slope.
6. Keep all movement on slopes slow and gradual. Do
not make sudden changes in speed or direction,
which could cause the machine to rollover.
7. Use extra care while operating machines with grass
catchers or other attachments; they can affect the
stability of the unit. Do not use on steeps slopes.
8. Do not try to stabilize the machine by putting your
foot on the ground (ride-on units).
9. Do not mow near drop-offs, ditches, or
embankments. The mower could suddenly turn over if
a wheel is over the edge of a cliff or ditch, or if an
edge caves in.
10. Do not use grass catchers on steep slopes.
11. Do not mow slopes if you cannot back up them.
12. See your authorized dealer/retailer for
recommendations of wheel weights or
counterweights to improve stability.
13. Remove obstacles such as rocks, tree limbs, etc.
14. Use slow speed. Tires may lose traction on slopes
even through the brakes are functioning properly.
15. Do not turn on slopes unless necessary, and then,
turn slowly and gradually uphill, if possible. Never
mow down slopes.
TOWED EQUIPMENT (RIDE-ON UNITS)
1. Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
2. Follow the manufacturer’s recommendations for
weight limit for towed equipment and towing on
slopes. See attaching a trailer under OPERATION.
3. Never allow children or others in or on towed
equipment.
4. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
5. Travel slowly and allow extra distance to stop.
6. Do not shift to neutral and coast down hill.
WARNING
Never operate on slopes greater than 17.6 percent
(10°) which is a rise of 3-1/2 feet (106 cm) vertically in
20 feet (607 cm) horizontally.
Select slow ground speed before driving onto slope.
Use extra caution when operating on slopes with rearmounted grass catchers.
Mow up and down the face of slopes, not across. Use
caution when changing directions and DO NOT
START OR STOP ON SLOPE.
4
WARNING: To avoid serious injury, operate your unit up and
down the face of slopes, never across the face. Do not operate
on slopes greater than 10 degrees. Make turns gradually to
prevent tipping or loss of control. Exercise extreme caution
when changing direction on slopes. Braking may be affected by
attachments. Reduce speed on slopes.
1. Fold this page along dotted line indicated above.
2. Hold page before you so that its left edge is vertically parallel to a tree
trunk or other upright structure.
3. Sight across the fold in the direction of hill slope you want to measure.
4. Compare the angle of the fold with the slope of the hill.
ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL
FOLD ALONG DOTTED LINE
T
H
I
S
I
S
A
1
0
D
E
G
R
E
E
S
L
O
P
E
10 DEGREES MAX.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION
OF RIDER WITH ATTACHMENT
5
SERVICE AND MAINTENANCE
Safe Handling of Gasoline
1. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
2. Use only approved gasoline containers.
3. Never remove the gas cap or add fuel with the engine
running. Allow the engine to cool before refueling.
4. Never fuel the machine indoors.
5. Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as near a
water heater or other appliance.
6. Never fill containers inside a vehicle or on a truck bed
with a plastic bed liner. Always place containers on
the ground away from your vehicle before filling.
7. Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer with
a portable container, rather than from a gasoline
dispenser nozzle.
8. Keep nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
9. If fuel is spilled on clothing, change clothing
immediately.
10. Never over-fill the fuel tank. Replace gas cap and
tighten securely.
11. Use extra care in handling gasoline and other fuels.
They are flammable and vapors are explosive.
12. If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
13. Replace all fuel tank caps and fuel container caps
securely.
Service & Maintenance
1. Never run the unit in an enclosed area where carbon
monoxide fumes may collect.
2. Keep nuts and bolts, especially blade attachment
bolts, tight and keep equipment in good condition.
3. Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if
they are not functioning properly.
4. Keep unit free of grass, leaves, or other debris buildup. Clean up oil or fuel spillage. and remove any fuelsoaked debris. Allow machine to cool before storage.
5. If you strike an object, stop and inspect the machine.
Repair, if necessary, before restarting.
6. Never make adjustments or repairs with the engine
running.
7. Check grass catcher components and the discharge
guard frequently and replace with manufacturer’s
recommended parts, when necessary.
8. Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
9. Check brake operation frequently. Adjust and service
as required.
10. Maintain or replace safety and instructions labels, as
necessary.
11. Do not remove the fuel filter when the engine is hot
as spilled gasoline may ignite. Do not spread fuel line
clamps further than necessary. Ensure clamps grip
hoses firmly over the filter after installation.
12. Do not use gasoline containing METHANOL, gasohol
containing more than 10% ETHANOL, gasoline
additives, or white gas because engine/fuel system
damage could result.
13. If the fuel tank must be drained, it should be drained
outdoors.
14. Replace faulty silencers/mufflers.
15. Maintain or replace safety and instruction labels as
necessary.
16. Use only authorized replacement parts when making
repairs.
17. Always comply with factory specifications on all
settings and adjustments.
18. Only authorized service locations should be utilized
for major service and repair requirements.
19. Never attempt to make major repairs on this unit
unless you have been properly trained. Improper
service procedures can result in hazardous operation,
equipment damage and voiding of manufacturer’s
warranty.
20. On multiple blade mowers, take care as rotating one
blade can cause other blades to rotate.
21. Do not change engine governor settings or overspeed the engine. Operating the engine at excessive
speed can increase the hazard of personal injury.
22. Disengage drive attachments, stop the engine,
remove the key, and disconnect the spark plug wire(s)
before: clearing attachment blockages and chutes,
performing service work, striking an object, or if the
unit vibrates abnormally. After striking an object,
inspect the machine for damage and make repairs
before restarting and operating the equipment.
23. Never place hands near the moving parts, such as a
hydro pump cooling fan, when the tractor is running.
(Hydro pump cooling fans are typically located on top
of the transaxle).
24. Units with hydraulic pumps, hoses, or motors:
WARNING: Hydraulic fluid escaping under pressure
may have sufficient force to penetrate skin and cause
serious injury. If foreign fluid is injected into the skin it
must be surgically removed within a few hours by a
doctor familiar with this form of injury or gangrene
may result. Keep body and hands away from pin
holes or nozzles that eject hydraulic fluid under high
pressure. Use paper or cardboard, and not hands, to
search for leaks. Make sure all hydraulic fluid
connections are tight and all hydraulic hoses and
lines are in good condition before applying pressure
to the system. If leaks occur, have the unit serviced
immediately by your authorized service center.
25. WARNING: Stored energy device. Improper release
of springs can result in serious personal injury.
Springs should be removed by an authorized
technician.
6
SAFETY & OPERATION DECALS
This unit has been designed and manufactured to
provide you with the safety and reliability you would
expect from an industry leader in outdoor power
equipment manufacturing.
Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and
effectively, we have placed several safety labels on the
unit to remind you of this important information while you
are operating your unit.
All DANGER, WARNING, CAUTION and instructional
messages on your rider and mower should be carefully
read and obeyed. Personal bodily injury can result when
these instructions are not followed. The information is for
your safety and it is important! The safety decals below
are on your rider and mower.
If any of these decals are lost or damaged, replace them
at once. Contact your dealer for replacements.
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.
Burn hazard
The exhaust pipe and surrounding
surfaces are hot and can cause
burns.
Avoid contact with hot surfaces.
WARNING
173xxxx
174xxxx
Right Ground
Speed Lever
(Controls Right Drive Wheel)
Forward
Neutral Start / Park
Reverse
174xxxx
Left Ground
Speed Lever
(Controls Right Drive Wheel)
Forward
NeutralStart / Park
Reverse
1733458
Low Cut
1
4
3
2
High Cut
OPERATION
To Stop the Engine:
1. Move ground speed levers to PARK
positions.
2. Move engine speed control to FAST.
3. Turn ignition switch to OFF.
FORWARD TRAVEL
To Turn On the Mower Blades:
1. Sit in seat.
2. Start the engine (see "To Start Engine").
3. Pull the mower blade switch UP to
turn the mower blades on.
To Drive:
1. Start the engine (see "To Start the Engine").
2. Move both ground speed levers in from
PARK position simultaneously. (Engine
will stop if levers are not moved in at the
same time).
3. Move levers as shown to travel.
To Turn the Mower Blades Off:
1. Push the mower blade switch DOWN to
turn the mower blades off.
START / PARK POSITION
REVERSE TRAVEL
LEFT TURN RIGHT TURN
1724236
1734276
Decal - Ground
Speed Lever
Part No. 1734271
Decal - Ground Speed Lever
Part No. 1734270
Decal - Cutting Height
Indicator
Part No. 1733458
Decal - Amputation Hazard
Part No. 1704276
Decal - Amputation and
Thrown Objects Hazard
Part No. 1704277
Decal - Operation, Lower
Part No. 1734207
Decal - Operation, Upper
Part No. 1734236
Decal - Cutting
Height Switch
Part No. 1734276
Decal - Hot Surfaces
Part No. 1734273
(Located on RH side)
Decal - Transmission
Release
Part No. 1734532
(Located on rear frame)
Decal - Control Panel
Part No. 1734272
DANGER
Amputation Hazard
1704276
To avoid injury from rotating
blades, stay clear of deck edge.
DANGER
Amputation and
Thrown Objects Hazard
1704277
To avoid injury from rotating blades and
thrown debris, stay clear of deck edge
and discharge. Do not mow without
deflector or entire grass catcher in place.
Choke
CLOSED
(Pull Knob Up)
OPEN
(Push Knob Down)
Ignition Switch
Engine Speed
FAST
SLOW
Mower Blades
ON
(Pull Up)
OFF
(Push Down)
1734272
Sit in the seat.
Move ground speed levers to START/PARK
positions (move both levers out).
Turn the mower blades OFF
(push switch down).
Move engine speed control to FAST position
(lever full forward).
Pull the choke knob up to CLOSED position.
Turn ignition switch to START to crank the engine.
After the engine starts:
-release the ignition switch key (it will return to RUN position)
-push the choke knob down to OPEN position
Always set the engine speed to FAST for driving and mowing.
To Start the Engine:
1
2
3
4
5
6
7
START/PARK
Roll-over hazard
Operating on slopes can cause loss of
control and roll-overs.
• If you cannot back-up a hill, do not drive
on it.
• If machine stops while going uphill,
turn the blades off and back down slowly.
• Avoid sudden turns.
• Go up and down slopes, not across.
DANGER
Avoid serious injury or death:
• Know the location and function of
all controls.
• Keep safety devices (guards, shields,
switches, etc.) in place and working.
• Remove objects that could be thrown by the blade.
• Be sure blade(s) and engine are stopped before
placing hands or feet near blade(s).
• When leaving machine, shut off, remove key, and
set parking brake.
WARNING
Amputation hazard
Rotating blades cut off arms and legs.
• Stop the mower when children or others are
near.
• Do not carry riders (especially children) even
with the blades off. They may fall off or return
for another ride when you are not expecting it.
• Look down and behind before and while
backing.
Carbon monoxide hazard
The engine emits poisonous carbon
monoxide gas.
• Avoid inhaling exhaust fumes.
• Only operate outdoors.
Fire hazard
Gasoline is flammable.
Yard debris is combustible.
• Allow engine to cool for at least 3 minutes
before refueling.
• Keep unit cleaned of debris.
• Read the operator's manual
before using this product.
10º Max.
10º Max.
DO NOT TOW THIS MACHINE!
Damage to transmission may result.
1724207
CLOSED
FAST
OFF
START
1
2
3
5
6
4
Decal - Tracking
Adjustment
Part No. 126638
Decal - Cutting Hazard
Part No. 1734672
(Located on rear frame)
Cutting
Height
RAISE
MOWER
LOWER
MOWER
1734276
7
IDENTIFICATION NUMBERS
ID Tag
When contacting the service center for replacement
parts, service, or information you MUST have these
numbers.
Record your model name/number, manufacturer’s
identification numbers, and engine serial numbers in the
space provided for easy access.
The identification tag is located on the underside of the
seat. Tilt the seat forward to access the ID tag.
SSAAMM
PP
LLEE
PRODUCT REFERENCE DATA
Model Description Name/Number
Part Number Unit Serial Number
Date Purchased
ENGINE REFERENCE DATA
Engine Make Engine Model
Engine Type/Spec Engine Code/Serial Number
OPERATION
8
Ground Speed Levers /
Parking Brake
These levers control the ground speed and parking brake
of the rider. The left lever controls the left rear drive
wheel and the right lever controls the right rear drive
wheel and parking brake.
Pushing the levers out to the side, away from the
operator’s lap, locks the parking brake in PARK position
(inset, Figure 1). This is the proper position for starting
the rider. Pulling the levers in across the operator’s lap
puts the levers in DRIVE positions.
From DRIVE position, moving a lever forward increases
the FORWARD speed of the associated wheel. Pulling
back on a lever increases the REVERSE speed. The
further a lever is pushed, the faster the drive wheel will
turn.
See DRIVING PRACTICE for steering instructions.
Engine Speed Control
The engine speed control adjusts engine speed. Always
set the engine speed to FAST for driving and mowing.
Move the engine speed control back to SLOW to
decrease engine speed. NEVER turn on the mower
blades with the engine speed set to SLOW. Only turn on
the mower blades with the engine speed set to FAST.
Choke
CLOSE the choke for cold starting (pull knob up). OPEN
the choke once the engine starts (push knob down). If
the engine is warm, it may not require choking. If this is
the case, set the choke to OPEN (push the knob down)
while cranking the engine. In most cases, you will need
to close the choke in order to start the engine.
Figure 1. Controls
Left
Ground Speed
Control Lever
Fuel Tank
Cap
Transmission
Release Levers
Right
Ground Speed &
Parking Brake
Lever
Mower
Cutting
Height
Switch
Ignition
Switch
Mower Blade
Switch
Engine
Speed
(Fast)
Engine
Speed
(Slow)
Choke
(Closed)
Choke
(Open)
OFF
RUN
START
Ground Speed Levers -
DRIVE Positons
Ground Speed Levers -
START/PARK Positons
CONTROL FUNCTIONS
The information below briefly describes the
function of individual controls. Starting,
stopping, driving, and mowing require the
combined use of several controls applied in
specific sequences. To learn what combination
and sequence of controls to use for various
tasks please read the entire section.
9
Mower Cutting Height Switch
To increase the mower cutting height (raise the mower
deck), press the top of the yellow cutting height switch.
To decrease mower cutting height (lower the mower
deck), press the bottom of the switch. Mower cutting
height range is approximately 3-3/4” to 1-1/2”. The
cutting height gauge indicates the position of the mower
deck. The cutting height gauge is located on the front of
the rider, just behind the driver’s left leg.
Ignition Switch
The ignition switch starts and stops the engine; it has
three positions:
OFF Stops the engine and shuts off the
electrical system.
RUN Allows the engine to run and powers the
electrical system.
START Cranks the engine for starting.
NOTE: Never leave the ignition switch in the RUN
position with the engine stopped. This drains the battery.
Hour Meter
The hour meter measures the number of hours the key
has been in the RUN position.
NOTE: The hour meter will register the passage of time
when the key is in the RUN position, even if the engine is
not running.
Mower Blade Switch
The yellow mower blade switch turns the mower blades
on and off. To turn the mower blades ON, pull the switch
up. To turn the mower blades OFF, push the switch
down. Always set the engine speed control to FAST
before turning the mower blades ON, and while mowing.
Transmission Release Levers
The transmission release levers deactivate the
transmissions so that the unit can be pushed by hand.
See PUSHING THE UNIT BY HAND for operational
information.
Fuel Tank
To remove the fuel tank cap, turn it counterclockwise.
GENERAL OPERATING SAFETY
Before first time operation:
• Be sure to read all information in the Safety and
Operation sections before attempting to operate this
rider and mower.
• Become familiar with all of the controls and how to stop
the unit.
• Drive in an open area without mowing to become
accustomed to driving the unit.
WARNING
If you do not understand how a specific control
functions, or have not yet thoroughly read the
CONTROL FUNCTIONS section, do so now.
Do NOT attempt to operate the rider without first
becoming familiar with the location and function
of ALL controls.
Loading...