Breville the Kitchen Wizz Quad BFP650, BFP650 the Kitchen Wizz Quad Instruction Booklet
www.breville.com.au
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2012.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
BFP650 Issue - A12
Australian Customers
Mail: PO Box 22
Botany NSW 2019
AUSTRALIA
Phone: 1300 139 798
Fax: (02) 9384 9601
Email:
Customer Service:
askus@breville.com.au
New Zealand Customers
Mail: Private Bag 94411
Botany Manukau 2163
Auckland NEW ZEALAND
Phone:
0800 273 845
Fax: 0800 288 513
Email:
Customer Service:
askus@breville.com.au
Breville Customer Service Centre
BFP650
the Kitchen Wizz Quad
™
Instruction Booklet
CONGRATULATIONS
on the purchase of your new
Breville Product
3
CONTENTS
4 Breville recommends safety first
7 Know your Breville Product
10 Assembling your Breville Product
14 Operating your Breville Product
30 Care & cleaning
33 Recipes
4
BREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE
• Carefully read all instructions before
operating the food processor for the first
time and save for future reference.
• Remove and safely discard any
packaging material and promotional
labels before using the food processor
for the first time.
• To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fitted to the power plug
of this appliance.
• Do not place the food processor near
the edge of a bench or table during
operation. Ensure the surface is level,
clean and free of water and other
substances. Vibration during operation
may cause the appliance to move.
• Do not use the food processor on a sink
drain board.
• Do not place this appliance on or near
a hot gas or electric burner, or where it
could touch a heated oven.
• Handle the food processor and
attachments with care – remember the
blades and discs are razor-sharp and
should be kept out of reach of children.
• Always make sure the food processor is
completely assembled before operating.
The appliance will not operate unless
properly assembled.
• Ensure the OFF button has been
pressed, and the food processor is
switched off at the power outlet and
unplugged before attaching the
processing blade, dough blade, disc, or
processing lid.
• Always secure the processing bowl onto
the motor base before attaching the
processing blade, dough blade or disc.
• Always operate the food processor with
the processing lid in position.
• Do not push food into the food chute
with your fingers or other utensils.
Always use the food pusher provided.
• Keep fingers, hands, knives and other
utensils away from moving blade
and discs.
• Do not place hands or fingers in the
processing bowl of the food processor
unless the motor, processing blade,
dough blade or disc has come to a
complete stop. Ensure the OFF button
has been pressed to switch the motor
off and the appliance is switched off at
the power outlet and the power cord is
unplugged before removing the lid from
the processing bowl.
• Ensure the motor and processing blade,
dough blade or disc, have completely
stopped before disassembling. Ensure
the OFF button has been pressed
and the appliance is switched off at
the power outlet and the power cord
is unplugged when not in use, if left
unattended and before disassembling,
cleaning or storing.
• Do not use attachments other than those
provided with the food processor.
• Do not attempt to operate the food
processor by any method other than
those described in this book.
IMPORTANT SAFEGUARDS
5
BREVILLE RECOMMENDS SAFETY FIRST
5
• Care should be taken when removing
the food from the processing
bowl by ensuring the motor and
processing blade, dough blade or
disc, have completely stopped before
disassembling. Ensure the OFF button
has been pressed to switch the motor
off, the appliance is switched off at
the power outlet and the power cord
is unplugged, before removing the lid
from the bowl. The processing bowl
should then be unlocked from the motor
body and the processing blade, dough
blade or disc carefully removed before
attempting to remove the
processed food.
• Some stiff mixtures, such as dough, may
cause the dough blade to rotate more
slowly than normal. In this unlikely
event of an excessive load, do not
operate the appliance continuously with
excessive load for more than 30 seconds.
• Do not process hot or boiling liquids -
allow liquids to cool before placing into
the processing bowl.
• Do not move the food processor whilst
in operation.
• Do not leave the food processor
unattended when in use.
• Do not place any part of the food
processor in the microwave oven.
• Do not fill the bowl above the 2L Max
level for wet and dry ingredients. Always
add drier or thicker ingredients to the
processing bowl prior to adding fluids.
• Do not place anything on top of the food
processor when the lid is on, when in use
and when stored.
• Keep the appliance clean. Follow the
cleaning instructions provided in
this book.
IMPORTANT SAFEGUARDS FOR
ALL ELECTRICAL APPLIANCES
• Fully unwind the power cord before use.
• Do not let the power cord hang over
the edge of a bench or table, touch hot
surfaces or become knotted.
• To protect against electric shock do not
immerse the power cord, power plug or
appliance in water or any other liquid.
• The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect
the appliance. To avoid a hazard do not
use the appliance if power cord, power
plug or appliance becomes damaged in
any way. Return the entire appliance to
the nearest authorised Breville Service
Centre for examination and/or repair.
• Any maintenance other than cleaning
should be performed at an authorised
Breville Service Centre.
• This appliance is for household use only.
Do not use this appliance for anything
other than its intended use. Do not use
in moving vehicles or boats. Do not use
outdoors. Misuse may cause injury.
• The installation of a residual current
device (safety switch is recommended
to provide additional safety protection
when using electrical appliances. It
is advisable that a safety switch with
a rated residual operating current
not exceeding 30mA be installed in
the electrical circuit supplying the
appliance. See your electrician for
professional advice.
6
BREVILLE RECOMMENDS SAFETY FIRST
WARNING
To avoid possible malfunction of the
processing bowl’s auto switch, do not
place the processing lid in the locked
position when the appliance is not
in use.
WARNING
The Quad
‰
processing blade and
discs are extremely sharp, handle with
care at all times. Do not place hands,
knives, or other utensils into the food
chute. Always use the food pusher to
push the food down the food chute.
SAVE THESE
INSTRUCTIONS
KNOW
your Breville Product
8
PAge heAder.....
KNOW YOUR BREVILLE PRODUCT
A. Large Food Pusher
For pushing food down the food chute.
B. Food Chute Used
For guiding food into the
processing bowl.
C. Processing Lid
Locks onto the processing bowl.
D. Fine Disc
Use one side for thin slicing and the
other side for fine shredding.
E. Coarse Disc Use
One side for thick slicing and the other
side for coarse shredding.
F. Grating Disc
Finely grates a variety of foods.
G. Storage Container
With lid for storing discs when they are
not in use.
H. OFF Button
Press to stop the food processor.
I. ON Button
Press to start the food processor.
J. PULSE Button
Press down and hold briefly for
short bursts of power. The motor will
automatically stop after the pulse button
has been released.
K. Power Light
A red light illuminates when the food
processor is connected to a power outlet
and the power outlet has been
switched on.
A
B
C
D
E
F
G
H
L
M
N
O
P
Q
R
I
K
J
9
KNOW YOUR BREVILLE PRODUCT
L. Direct Drive Motor Base
With safety braking system.
M. Non-Skid Rubber Feet
For added safety and stability.
N. Small Food Pusher
For pushing food down the food chute.
It also doubles as a measuring cup
for adding/measuring ingredients. Its
primary use is to push food down the
food chute.
O. Attachment Spindle
Fits onto the motor base shaft and is
used to hold the Quad
®
processing
blade, dough blade, discs,processing
bowl and processing lid in place.
P. Silicone Seal
Reduces the chance of leakage
while processing large volumes of
wet ingredients.
Q. Processing Bowl
With handle 2 litre processing bowl for
wet and dry ingredients, locks onto the
motor base.
R. Quad
®
Processing Blade
Swift action for chopping, mixing,
whipping and blending a variety
of foods.
Safety automatic switch
Prevents the motor from operating
unless the bowl and lid are correctly
locked in position.
Indented base
Designed for easy lifting and manoeuvring
of the food processor.
Cord storage
Allows the power cord to be neatly wrapped
at the rear of the food processor.
ACCESSORIES NOT SHOWN
Dough blade
Softer action for combining dough ingredients.
Storage lid
For processing bowl allows food to be stored
in the cupboard or in the refrigerator for
short periods of time.
Double ended cleaning brush
For cleaning the inside of the processing
blade (small end can be used for small
crevices of the Quad
®
blade and dough
blade shafts).
Plastic spatula
For scraping the sides of the bowl and
helping to process ingredients evenly.
ASSEMBLING
your Breville Product
11
ASSEMBLING YOUR BREVILLE PRODUCT
Before using your food processor, become
familiar with all the parts.
Remove all packaging materials and
promotional labels, being careful when
handling the Quad
®
processing blade
and discs as they are very sharp. Wash the
processing bowl, processing lid and other
attachments in warm, soapy water. Rinse
and dry thoroughly. (Refer to cleaning, care
and storage section).
1. Place the motor base on a dry, level work
surface. Place the attachment spindle
onto the motor base shaft. Place the
processing bowl over the attachment
spindle, with the handle in line with the
‘align handle’ symbol on the motor base.
2. Turn the processing bowl clockwise until
the handle locks properly into position.
3. The Quad® processing blade, dough
blade, or one of the discs can now be
positioned on the attachment spindle in
or above the processing bowl.
a) Processing blades
Carefully grasp either the Quad
®
processing blade or dough blade
using the central plastic support
and position it over the attachment
spindle and push down until
inserted correctly.
b) Discs
Carefully choose the side of the disc
you wish to use so that the process
you require is facing upwards.
Hold the disc by the smooth edges
with both hands and position the
central hole above the attachment
spindle and push down until
inserted correctly.
12
ASSEMBLING YOUR BREVILLE PRODUCT
4. Place the processing lid onto the
processing bowl so the food chute
is slightly right of the bowl handle.
Holding the handle of the bowl and
the food chute at the same time, turn
the lid clockwise to align it with the
LOCK symbol on the bowl handle. The
LOCKING TAB on the lid will slot into
the INTERLOCKING SAFETY CATCH
on the handle. The lid should be now
securely locked into position.
NOTE
The food processor will not operate
unless both the processing bowl and
lid are correctly locked into position.
NOTE
Your Breville food processor is
equipped with a silicon seal, located
in a recess around the outer rim of
the food processor bowl lid, to reduce
leakage while processing larger
volumes of wet ingredients. The
silicon seal is removable for cleaning
purposes (refer to Cleaning and Care).
5. Insert the power plug into a 230/240
volt power outlet and switch the power
outlet on.
The red power light illuminates. Your
food processor has ON, OFF and PULSE
buttons to give total control when
processing food. Press the ON button
to switch the motor on and operate
continuously. Press the OFF button to
switch the motor off. When short bursts
of power are required, press the PULSE
button and hold down briefly, release,
then press again. The PULSE action will
automatically stop when the button
is released.
6. After processing, always wait until the
blades or discs have stopped spinning
before unlocking and removing the lid.
To remove the processing lid, ensure the
OFF button has been pressed, the power
is switched off at the power outlet and
the cord is unplugged from the power
outlet. Holding the handle of the bowl
and the food chute at the same time,
turn the lid anti-clockwise (as indicated
by the symbol) and lift off.
NOTE
As a safety feature, the food processor
will automatically switch off when the
lid is unlocked, however, it is good
practice to manually switch off the
food processor using the OFF button
before removing the lid.
7. Remove the processing bowl (before
removing blade or discs) by turning it
anti-clockwise until the handle is in line
with the UNLOCK symbol. Lift the bowl
off the attachment spindle.
WARNING
The Quad‰ processing blade and discs
are extremely sharp, handle with care
at all times.
13
ASSEMBLING YOUR BREVILLE PRODUCT
OVERLOAD PROTECTION SYSTEM
The motor is protected from burning out by
an automatic, temperature operated, cut-out
switch. If the food processor is overloaded
or operated continuously for too long, the
motor may overheat. If this happens, the
power on light will continue to illuminate
even though the safety cut-out switch will
prevent the food processor from operating.
To operate the food processor again, you
must switch off, unplug and allow to cool for
approximately 30 minutes. Once the motor
has fully cooled, it is ready for use again.
Some stiff mixtures, such as dough, may
cause the dough blade to rotate more slowly
than normal. In this unlikely event of an
excessive load, do not operate the appliance
continuously with excessive load for more
than 30 seconds.
If the blades or discs should jam while
processing, ensure the OFF button is
pressed to switch the motor off and the food
processor is switched off at the power outlet
and the power cord is unplugged. Remove
the processing lid and adjust any food
wedged between the blade and the bowl or
in the disc. Replace the lid and proceed as
normal. If this occurs again, the processing
bowl may be overloaded, so remove some of
the food and process in smaller batches.
NOTE
The food processor is designed so
the motor will not operate without
the processing bowl and lid correctly
locked into position. In the event that
the food processor starts without the
lid correctly locked into position,
immediately disconnect at the power
outlet and return to your local Breville
Service Centre for examination.
The food processor can process foods in a
variety of ways depending on which blade or
disc you choose.
8. When removing the discs - carefully
remove the disc by placing one hand
on each side of the smooth edge and by
lifting the disc above the attachment
spindle on the motor shaft.
When removing the processing blades carefully remove the Quad
®
processing
blade or dough blade by grasping the
central plastic support and lifting above
the attachment spindle on the
motor shaft.
NOTE
Reassemble the food processor by
locking the bowl into position before
attaching blades, disc or lid.
NOTE
Care should be taken when removing
the food from the processing bowl
by ensuring the motor and Quad
®
processing blade, dough blade or
disc, have completely stopped before
disassembling. Ensure the OFF button
is pressed to switch the motor off,
the appliance is switched off at the
power outlet and it is unplugged,
before removing the lid from the bowl.
The processing bowl should then be
unlocked from the motor body, then
the Quad
®
processing blade, dough
or disc carefully removed before
attempting to remove the
processed food.
OPERATING
your Breville Product
Loading...