Breville CBL6 User Manual

CBL6 Power Blender

CBL6_IB_FA.indd 1 9/4/09 2:07:12 PM

Contents

Page

Breville Recommends Safety First 4

Know your Breville P

ower Blender 6

Operating

Your Breville Power Blender 7

Care, Cleaning and Stora

ge 9

Hints and T

ips on how to use your Breville Power Blender 10

Suggested Uses for your Breville Po

wer Blender 11

Suggested Uses Chart 11

Recipes R

CBL6_IB_FA.indd 2 9/4/09 2:07:12 PM

Congratulations

on the purchase of your new Breville Power Blender

CBL6_IB_FA.indd 3 9/4/09 2:07:14 PM

Breville recommends safety ﬁrst

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

Carefully read all instructions before operating the Breville Power Blender for the ﬁrst time and save for future reference.

Remove and safely discard any packaging material and promotional labels before using the blender for the ﬁrst time.

To eliminate a choking hazard for young children, remove and safely discard the protective cover ﬁtted to the power plug of this appliance.

Do not place the blender near the edge of a bench or table during operation. Ensure the surface is level, clean and free of water and other substances. Vibration during operation may cause the appliance to move.

Do not use the blender on a sink drain board. Do not place the blender on or near a hot gas or electric

burner, or where it could touch a heated oven. Handle the blender and attachments with care

– remember the blades are razor-sharp and should be kept out of the reach of children.

Always ensure the blender is completely assembled before operating. The blender will not operate unless properly assembled.

Do not use attachments other than those provided with the blender.

Do not attempt to operate the blender by any method other than those described in this book.

Always secure the blade assembly onto the blender jug before attaching to the motor base.

Ensure the speed selection dial is in the OFF position and the blender is switched off at the power outlet and the power cord is unplugged before attaching the blender jug.

Always operate the blender with the blender jug lid in position.

•

Keep ﬁngers, hands, knives and other utensils away from moving blades.

Do not place hands or ﬁngers into the blender jug unless the motor and blades have come to a complete stop. Ensure the speed selection dial is in the OFF position and the appliance is switched off at the power outlet and the power cord is unplugged before removing the lid from the blender.

Ensure the motor and the blades have completely stopped before disassembling. Ensure the speed selection dial is in the OFF position and the appliance is switched off at the power outlet and the power cord is unplugged from the power outlet before attempting to move the blender, when not in use, if left unattended and before disassembling, cleaning or storing.

Care should be taken when removing the food from the blender jug by ensuring the motor and the blades have completely stopped before disassembling. Ensure the speed selection dial is turned to the OFF position, the appliance is switched off at the power outlet and unplugged, before removing the lid from the blender jug. The blender jug should then be lifted from the motor base and the food carefully removed before attempting to remove the blade assembly.

Do not operate the blender continuously for periods longer than 30 seconds on any setting or if processing a heavy load. None of the recipes in this book are considered a heavy load. If the blender is operated continuously for too long, it should be switched off, unplugged and allowed to cool for 30 minutes before recommencing.

Do not process hot or boiling liquids – allow liquids to cool before placing into the blender jug.

Do not move the blender whilst in operation. Do not leave the blender unattended when in use.

•

IMPORTANT SAFEGUARDS FOR YOUR BREVILLE POwER BLENDER

CBL6_IB_FA.indd 4 9/4/09 2:07:14 PM

Unwind the power cord fully before use.

Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted.

To protect against electric shock do not immerse the power cord, power plug or motor base in water or any other liquid.

The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

It is recommended to regularly inspect the appliance. To avoid a hazard do not use the appliance if power cord, power plug or appliance becomes damaged in any way. Return the entire appliance to the nearest authorised Breville Service Centre for examination and/or repair.

Any maintenance other than cleaning should be

•

performed at an authorised Breville Service Centre.

This appliance is for household use only. Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors. Misuse may cause injury.

The installation of a residual current device (safety switch is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice.

•

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

Do not place any part of the blender in the microwave oven.

Do not place the motor base, lid, inner measuring cup, silicon seal, blender jug base or blade assembly into a dishwasher.

•

Do not place anything on top of the blender jug when the lid is on, when in use and when stored.

Keep the blender clean. Follow the cleaning instructions provided in this book.

•

CBL6_IB_FA.indd 5 9/4/09 2:07:14 PM

Know Your Breville Power Blender

CBL6 BREVILLE POwER BLENDER

Inner measuring cup - for adding ingredients whilst blending

Large 1.25 litre glass jug 2 speeds plus pulse Ice crushing stainless steel blades

Non-slip feet Blade assembly – easily removable for cleaning Blender jug base Motor base

CBL6_IB_FA.indd 6 9/4/09 2:07:15 PM

Before ﬁrst use

Remove and safely discard any packaging material and promotional labels.

Disassemble the blender jug by following Steps 3 to 5 in ‘Disassembling the blender’ and wash the lid, inner measuring cup, blender jug, silicon seal, blender jug base and blade assembly in warm, soapy water with a soft cloth. Rinse and dry thoroughly.

Wipe the motor base with a damp cloth and dry thoroughly.

Disassembling the blender

Place the motor base on a ﬂat, dry surface such as a bench top. Ensure that the speed selection dial is in the OFF position, the appliance is switched off at the power outlet and the power cord is unplugged.

Remove the blender jug from the motor base by holding the motor base ﬁrmly and grasping the blender jug handle and pulling the blender jug up and off the motor base.

Remove the lid and inner measuring cup from the blender jug.

Place the blender jug upside down on a ﬂat, dry surface such as a bench top.

Hold the jug handle and turn the blender jug base anti-clockwise to remove. Carefully lift the blade assembly out of the narrow end of the blender jug. Remove the silicon seal from outside the narrow end of the blender jug.

Assembling and attaching the blender jug

Place the motor base on a ﬂat, dry surface such as a bench top. Ensure the speed selection dial is in the OFF position, the appliance is switched off at the power outlet and the power cord is unplugged.

Operating Your Breville Power Blender

Place the blender jug upside down on a ﬂat, dry surface such as a bench top.

Hold the jug handle and place the silicon seal onto the narrow end of the blender jug then carefully insert the blade assembly.

Place the blender jug base over the blade assembly and turn clockwise to secure into position.

Turn the assembled blender jug upright and place onto the motor base.

Insert the inner measuring cup into the lid then insert the lid ﬁrmly into the top of the blender jug.

Using the blender

Ensure the speed selection dial is in the OFF position. Insert the power plug into a 230/240V power outlet and switch on at the power outlet.

Remove the lid and add food and/or liquid into the blender jug.

Insert the inner measuring cup into the lid then insert the lid ﬁrmly into the top of the blender jug.

NOTE

The blending blades are extremely sharp. Avoid any contact with fingers and hands.

NOTE

Ensure lid is placed onto the blender jug firmly and the inner measuring cup is in position before operating the blender. Do not operate the blender without the lid on. Additional ingredients can be added whilst blending by removing the inner measuring cup and placing or pouring ingredients through the opening in the lid.

NOTE

Liquids should be placed into the blender jug before solid ingredients, unless specified differently in a recipe.

NOTE

When using the blender for the first time, you may notice an odour coming from the motor. This is normal and will dissipate with use.

NOTE

All foods should be cut into cubes (approx. 2-3cm square) to achieve an even result.

CBL6_IB_FA.indd 7 9/4/09 2:07:15 PM

Operating Your Breville Power Blender continued

Select the desired speed by turning the speed selection dial clockwise to the desired setting LOW or HIGH. The speed can be changed at any time during the blending process. Turn the speed selection dial anti-clockwise to select the PULSE setting.

LOW speed is suitable for emulsions such as mayonnaise, dressings and marinades and for foods such as batters which require mixing until just combined.

HIGH speed is suitable for pureeing, crumbing, thickening, creaming and grinding.

PULSE can be used for foods that require short bursts of power to process such as herbs, nuts, small vegetables and ice. When using the PULSE setting, hold the blender lid in place.

During the blending process, some ingredients may stick to the sides of the blender jug. To push the food back onto the blades, turn speed selection dial to the OFF position and switch off at the power outlet. Remove the lid and use a plastic spatula to scrape down the sides of the blender jug. Replace the lid before recommencing blending.

At the end of use, always ensure the speed selection dial is turned to the OFF position. Then switch the appliance off at the power outlet and unplug the power cord.

NOTE

If any moisture or liquid appears on top of the motor base, ensure the speed selection dial is in the OFF position, the appliance is switched off at the power outlet and the power cord is unplugged, remove the blender jug then wipe the spillage immediately with kitchen paper towel and dry thoroughly. Ensure the blender jug is correctly assembled before placing back onto the motor base and operating.

NOTE

Ensure the motor and blades have completely stopped before attempting to move the appliance, when not in use, if left unattended and before disassembling, cleaning and storing

VER PLACE ANYTHING OTHER THAN FOOD AND LIQUIDS IN THE BLENDER wHILST THE MOTOR IS RUNNING.

CBL6_IB_FA.indd 8 9/4/09 2:07:15 PM

Care and cleaning

Before cleaning, ensure the speed selection dial is in the OFF position, the appliance is switched off at the power outlet and the power cord is unplugged from the power outlet.

Cleaning the blender jug, lid, inner measuring cup, silicon seal, blender jug base and blade assembly

Wash blender jug, lid, inner measuring cup, silicon seal, blender jug base and blade assembly in warm soapy water with a soft cloth. Use a kitchen bottle brush to dislodge stubborn food. Rinse and dry thoroughly. Do not place the motor base, lid, inner measuring cup, silicon seal, blender jug base or blade assembly into a dishwasher.

Cleaning the motor base

Wipe the motor base with a soft, damp cloth then dry thoroughly. Wipe any excess food particles from the power cord.

NOTE

The blender jug can be washed on a normal cycle in the dishwasher. Remove the lid, inner measuring cup, silicon seal, blender jug base and blade assembly before placing the blender jug upside down in the dishwasher for better stability.

NOTE

Do not use abrasive scouring pads or cleaners when cleaning the motor base as they may scratch the surface.

E BLENDING BLADES ARE EXTREMELY SHARP. AVOID ANY CONTACT wITH FINGERS AND HANDS.

USE CAUTION wHEN HANDLING AND STORING.

Removing stubborn or strong food stains and odours

Strong smelling foods such as garlic and ﬁsh may leave an odour and some vegetables such as carrots may leave a stain on the blender jug and lid. To remove, soak blender jug and lid in warm soapy water for 5 minutes. Then wash with a mild detergent and warm water, rinse well and dry thoroughly.

Storage

Store the blender upright with the blender jug, silicon seal, blade assembly, blender jug base, lid and inner measuring cup assembled and inserted on the motor base or beside it. Do not place anything on top.

CBL6_IB_FA.indd 9 9/4/09 2:07:15 PM

+ 19 hidden pages