Breville BWC200 User Manual

Breville Customer Service Centre

the Chill Control™

Instruction Booklet

Australian Customers
Mail: PO Box 22

Botany, NSW, 2019
AUSTRALIA

Phone: [phone]
Fax: [phone]
Email:

Customer Service:

[e-mail]

www.breville.com.au

Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.

Due to continued product improvement, the products illustrated/photographed

in this booklet may vary slightly from the actual product.

Copyright Breville Pty. Ltd. 2012.

New Zealand Customers
Mail: Private Bag 94411

Botany Manukau 2163
Auckland NEW ZEALAND

Phone:
Fax: [phone]
Email:

[e-mail]

0800 273 845

Customer Service:

BWC200 Issue - E12 BWC200

CONGRATULATIONS

CONTENTS

4 Breville recommends safety first

6 Know your Breville Chill Control™

on the purchase of your new

Breville Chill Control™

8 Operating your Breville

Chill Control™

14 Care & Cleaning

16 Troubleshooting

3

BREVILLE RECOMMENDS SAFETY FIRSTBREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE

• Carefully read all instructions before

operation and save for future reference.

• Remove and safely discard any

packaging material and promotional
labels before using the Breville
Chill Control™ for the first time.

• To eliminate a choking hazard for

young children, remove and safely
discard the protective cover fitted to the
power plug of this appliance.

• Do not place the Breville Chill Control™

near the edge of a bench or table during
operation.

• Do not place the appliance on or near

a hot gas burner, electric element or
where it could touch a heated oven.

• Do not operate the appliance on a sink

or drain board.

• Ensure that the surface is level, clean

and free of water.

• The Breville Chill Control™ is not

intended to be operated by means of
an external timer or separate remote
control system.

• To protect against electric shock, do not

immerse the power base, power cord or
power plug in water or allow moisture
to come in contact with these parts.

• Always switch the Breville Chill

Control™ Off at the power outlet and
unplug if the appliance is not in use,
before cleaning, before attempting to
move the appliance, disassembling,

assembling and when storing the
appliance.

• The Breville Chill Control™ is not

intended for use by young children or
infirm persons unless they have been
adequately supervised by a responsible
person to ensure they can use the
appliance safely.

• The Breville Chill Control™ has been

designed specifically for the purpose
of filtering and chilling water and must
only be used with municipally treated
water. Do not attempt to filter untreated,
raw water or water of unknown quality.

• Do not place the appliance directly

against the wall. Ensure there is
adequate airflow at the rear and sides
by positioning the appliance 10cm
away from the wall.

• Filter replacement is essential for the

product to perform as represented and
must be replaced every 8 weeks.

• Remove and empty the pre-filter tank

before changing filter.

• This appliance has been designed to be

used continuously.

• Do not operate without a filter in place.

• Keep the appliance and accessories

clean. Follow the Care and Cleaning
instructions provided on Page 14.

WARNING

Never immerse the power base, power
cord or power plug in water or allow
moisture to come into contact with
these parts.

IMPORTANT SAFEGUARDS FOR
ALL ELECTRICAL APPLIANCES

• This appliance is for household use only.

• Unwind power cord fully before use.

• Do not let power cord hang over the

edge of a table or counter, or touch
hot surfaces.

• Do not use the appliance for anything

other than its intended purpose as
described in this instruction book.
Do not use outdoors. Do not use in
moving vehicles or boats.

• Close supervision is necessary when any

appliance is used by or near children.

• Regularly inspect the supply cord, plug

and actual appliance for any damage.
Do not operate if damaged in any way
or after the appliance malfunctions.
Immediately cease use of the appliance
and call Breville Customer Service on
ph: 1300 139 798 (Australia) or
ph: 0800 273 845 (New Zealand).

• If the supply cord is damaged, it must be

replaced by the manufacturer, its service
agent or similarly qualified person in
order to avoid a hazard.

• Always turn the power Off and remove

the plug before cleaning.

• For any maintenance other than

cleaning, call Breville Customer Service
on ph: 1300 139 798 (Australia) or
ph: 0800 273 845 (New Zealand).

• Consult a qualified electrician if

the grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded.

BREVILLE ASSIST™ PLUG

The Breville Chill Control™ comes with a
unique Assist™ Plug, conveniently designed
with a finger hole in the power plug for easy
and safe removal from the wall outlet.

For safety reasons it is recommended you
plug your Breville Chill Control™ directly
into its own electrical outlet on a dedicated
circuit separate from other appliances. If the
electrical circuit is overloaded with other
appliances, your appliance may not function
properly. Using in conjunction with a power
strip or extension cord is not recommended.

SAVE THESE
INSTRUCTIONS

4 5

5

KNOW YOUR BREVILLE CHILL CONTROL™

KNOW

your Breville Chill Control™

G

A

B

C

D

E

F

H

I

A. 2 Litre Pre-Filter Water Tank
B. 4 Litre Filtered Water Tank
C. Variable Temperature Slider
D. LED Indicator
E. Water Dispenser Lever
F. 1 Litre Stainless Steel Cooling

Reservoir

G. BRITA‰ Memo - electronic cartridge

exchange indicator

H. BRITA
I. Extra Tall Height For Bottles

‰

MAXTRA Water Filter Cartridge

NOT SHOWN

Removable Plug - For easy cleaning
Breville Assist™ Plug

7

OPERATING YOUR BREVILLE CHILL CONTROL™

OPERATING

your Breville Chill Control™

BEFORE FIRST USE

Before first use, remove and safely discard
all promotional labels and packing materials
attached to the Breville Chill Control™.

Remove the filter cartridge from the plastic
packaging and keep in a safe place. Do not
re-insert the filter until (a) flushing process
and (b) preparation of filter cartridge has
been completed (refer to page 10).

Remove the lid, plastic plug and pre-filter
tank and wash in warm soapy water. Rinse
and wipe dry using new cloth. Wipe exterior
of appliance with a soft damp cloth and
dry thoroughly.

Place the appliance on a dry, flat level
surface. Plug into 230-240V outlet and
turn power On.

NOTE

Do not place the appliance directly
against the wall. Ensure there is
adequate airflow both at the rear and
sides by positioning the appliance
10cm away from the wall.

FLUSHING THE BREVILLE
CHILL CONTROL

3. Position the variable temperature slider

to the centre.

4. Place a large container or jug under

the spout.

5. Press the dispenser lever until water

reaches the MIN level, then discard
remaining water.

6. Repeat this process with cold tap water

twice and discard.

7. Do not fill above the maximum level

indicated.

NOTE

If the plastic plug is inserted while
the cooling tank is empty, it will take
approximately 7 minutes for the air to
release from the cooling tank.
During this time chilled water cannot
be dispensed.

THE BRITA‰ MAXTRA CARBON
FILTRATION PROCESS

Activated carbon reduces chlorine, metals
such as lead, copper and limescale for
cleaner, clearer better tasting water.

Leaves in flouride.

It is important that you flush and rinse out
the dispensing system before using the
appliance for the first time.

Please note you should carry out these steps
without the BRITA
place. Plug the appliance into an appropriate
electrical outlet and switch On.

1. Remove filter cartridge from the

pre-filter tank and the removable plug
from filter tank.

2. Fill the pre-filter tank to the maximum

level with water.

‰

MAXTRA cartridge in

PREPARING THE BRITA‰ MAXTRA
FILTER CARTRIDGE

1. Remove the filter cartridge from its

wrapping.

NOTE

It is normal for the cartridge to
appear moist when removed from its
wrapping, this is simply condensation.

9

OPERATING YOUR BREVILLE CHILL CONTROL™ OPERATING YOUR BREVILLE CHILL CONTROL™

2. Immerse the filter cartridge in cold

water and agitate gently to remove
any air bubbles.

3. Insert the cartridge into the cartridge

housing of the pre-filter tank and push
firmly into place until it clicks into
position.

4. Take the pre-filter tank out of the water

tank, fill it under the tap with cold tap
water and allow it to filter through.
Discard the first two fillings. They are
used to flush the filter cartridge.

5. Place the pre-filter tank back into the

unit and refill with water. Ensure the
water is always above the minimum
level for optimum flow rate.

6. The Breville Chill Control™ is now

ready for use.

NOTE

Repeat the above process every time
you insert a new cartridge.

7. Once the water has been filtered, the

pre-filter tank can be refilled. Water will
filter through as it dispensed into the
filter tank water.

It will take 6 minutes on average to
filter 1 litre of water through the

‰

BRITA

MAXTRA cartridge.

LED INDICATOR

The WHITE light will turn On first to
indicate the appliance is in cooling mode.

When the water inside the cooling reservoir
has chilled (approximately 75 minutes )
the LED indicator will change to BLUE.

In warmer climates the time to chill will
take longer.

ADJUSTING THE WATER
TEMPERATURE

The variable temperature slider allows you
to adjust the temperature of filtered water
to suit your taste.

The temperature of the water will vary
depending on the selection made.

Slide the lever to the far left for the coldest
setting or to the right for room temperature
filtered water.

A selection in the middle will give you
filtered water somewhere between chilled
and room temperature.

NOTE

The LED indicator does not change
colour when adjusting the variable
temperature control slider.

NOTE

If dispensing more than 1 litre of
chilled water at one time, it will
take approximately 75 minutes for
another litre of water to be chilled to
minimum temp.

NOTE

We recommend you change the

‰

MAXTRA filter every 8 weeks.

BRITA

Replacement filters can be purchased
through major retail outlets or via
store.brita.com.au.

For additional questions on the
BRITA replacement filters, please
contact BRITA Consumer Service on
1300 557 762.

AUTO PROTECTION MODE

If there is an error with internal electronics
or the fan is externally obstructed, the LED
will start to flash, alternating between BLUE
and WHITE and the appliance will enter
into auto protection mode.

To reset the appliance, unplug the unit from
the power outlet, wait for a few minutes until
the LED stops flashing, and plug back into
power outlet.

If the LED continues to flash once reset,
contact Breville Customer Service
1300 139 798 for further assistance.

USING THE BRITA® MEMO

It is important to change your filter
cartridge regularly to enjoy the benefits
of filtered water.

The BRITA
indicator) reminds you when your filter
cartridge needs to be changed. It is
automatically calibrated according to
average use of 1 litre of water per day
and will remind you to change your filter
every 8 weeks.

‰

Memo (electronic exchange

SETTING THE BRITA® MEMO

Once you have fitted and prepared your
filter cartridge, start the BRITA
as follows:

1. Press and hold the START button until

4 bars appear on the display and flash
twice. The filter replacement reminder
is now set.

2. The flashing dot in the corner of the

display indicates the filter replacement
reminder is working.

3. At the end of every 2 weeks, 1 bar will

disappear indicating the remaining
cartridge life. Ensure you have a new
replacement BRITA
filter cartridge available when only
1 bar is showing.

‰

Memo

‰

MAXTRA water

10 11

OPERATING YOUR BREVILLE CHILL CONTROL™

4. All 4 bars will disappear and a flashing

arrow will appear to indicate the
cartridge should be replaced after
8 weeks.

5. Wash and dry the pre-filter tank, and

insert a new cartridge (see Preparing
the Filter Cartridge on page 10).

6. To set the BRITA

‰

Memo, see

instructions on page 11.

NOTE

‰

The BRITA
be used only with BRITA

Memo is intended to

‰

filter

cartridges.

REMOVING THE FILTER CARTRIDGE

When it is time to replace the cartridge after
8 weeks use, simply lift the ring pull handle
on top of the cartridge to remove.

The cartridge may be disposed of in
household waste or you can contact the

‰

BRITA

consumer service for advice on

Ph: 1300 557 762 for advice on recycling.

More information on the use of BRITA
cartridge and the BRITA
found in the BRITA

‰

Memo can be

‰

information Guide.

‰

filter

12 13

CARE & CLEANING FOR YOUR BREVILLE CHILL CONTROL™

CARE & CLEANING

for your Breville Chill Control™

CARE & CLEANING

1. Switch the appliance Off and unplug

the power cord from the power outlet
before cleaning.

2. Remove the lid, pre-filter tank and

water from the filter tank.

3. To empty the stainless steel cooling

reservoir, remove the plastic plug that
separates the filtered water from the
cooling reservoir.

4. Turn the appliance upside down to

drain any remaining water from the
cooling reservoir.

5. Wipe the inside of the filter tank

and cooling reservoir with a clean,
damp cloth.

6. Wash the lid, pre-filter tank and plastic

plug in warm soapy water using a mild
detergent and dry thoroughly.

7. Wipe exterior of appliance with a soft,

damp cloth.

8. Do not immerse the base in water or

any other liquid

REMOVABLE PLASTIC PLUG

The Breville Chill Control™ includes a
removable plastic plug that separates
filtered from chilled water. As well as
making the cleaning of the cooling
reservoir easy, it assists in the cooling
process to keep the water cool.

The plastic plug can be dismantled for
cleaning. Simply squeeze the sides to
release as shown below and wash with
warm soapy water.

STORAGE

Ensure the Breville Chill Control™ is
switched Off, all internal tanks are
emptied of water and it is clean and dry
before storing.

Stand the Breville Chill Control™ upright
on the power base. Do not store anything
on top.

Flush the appliance again before using
again (see instructions on page 9)

NOTE

Do not use alkaline or abrasive
cleaning agents, steel wool or
scouring pads as these can damage
the surface of the appliance.

Do not place any part of this appliance
in a dishwasher.

15

TROUBLESHOOTING

PAGE HEADER.....

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Filtered water not cold
enough

• Water chiller positioned

in direct sunlight

Move water chiller away
from direct sunlight.

After filling-up 1 litre
water bottle, water is not
cold anymore

Fan too noisy/does not
switch off

How do I know the water
has chilled?

LED not switching from
WHITE to BLUE

• High ambient

conditions (30˚C +)

• Water Chiller too close

to wall

• Water Chiller has not

been switched ON long
enough.

• Chilling tank capacity

is approximately 1 litre.
It takes approximately
75 minutes to chill
1 litre water from
room temperature.

• High ambient

conditions (30˚C +)

• Unit is running in

high power mode

• Initial water

temperature in chill
tank is too high

In warmer conditions,
the time to chill will
take longer.

Position water chiller
min 10cm clearance away
from walls.

Wait approximately
75 minutes after filling
with tap water.

Wait approximately
75 minutes after
dispensing large
amount of chilled water.

In warmer conditions,
the time to chill will
take longer.

The LED light will switch
from WHITE to BLUE.

Move water chiller away
from direct sunlight.

• High ambient

conditions (30˚C +)

• Water Chiller too close

to wall

• Water Chiller has not

been switched ON
long enough

16 17

In warmer conditions,
the time to chill will
take longer.

Position water chiller
min 10cm clearance away
from walls.

Wait approximately
75 minutes after filling
with tap water.

PROBLEM POSSIBLE CAUSES WHAT TO DO

NOTESTROUBLESHOOTING

LED indicator flashing
& alternating between

• Water Chiller is in Auto

Protection Mode

WHITE & BLUE

Water does not flow
during initial flushing

• Air lock in internal

tubing

Flow rate of water slow • Not enough water in

water tank

Water tank has small
dark particles

• Brita filter cartridge

& unit have not been
flushed

Fan externally obstructed
or an error with the internal
electronics.

Unplug the unit & wait a
few minutes to reset the
unit.

If problem persists call
Breville Customer Service
1300 139 798

With the chilling chamber
full, move slider to the
middle position and
use the plug like a sink
plunger while holding the
dispensing paddle open to
clear the air lock.

Ensure the water level is
always above the MIN level
for optimum flow rate.

Immerse the filter cartridge
in cold water and agitate to
remove air bubbles.

Flush the unit twice before
each new cartridge.

How can I clean the
chilling chamber

Remove the plastic plug in
the filter tank to clean the
chilling chamber.

There is a flashing arrow
& no bars appearing on
the Brita Memo indicator

What does the Brita Filter
cartridge remove from
the water?

• The Brita Filter

cartridge may need
to be replaced

Brita Filter Cartridge
should be replaced every
8 weeks.

The Brita Filter reduces
chlorine, metals such as
lead, copper, & limescale.
Leaves in flouride.

Where can I purchase the
Brita Filter cartridges

Brita filter cartidges are
available at all leading
retailers or contact Brita
Consumer Service
Ph: 1300 557 762

18 19