Breville BSB530XL User Manual

TYPESET V1

the All In One

™

Instruction Booklet - Livret d’instructions

BSB530XL

TYPESET V1

CONGRATULATIONS

on the purchase of your Breville product

Register online for product support

and exclusive offers.

USA Consumers: www.brevilleusa.com

Canadian Consumers: www.breville.ca

*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.

*

CONTENTS

4 Breville recommends safety first

7 Know your Breville product

9 Assembly & operation of your

Breville product

20 Care, cleaning & storage of your

Breville product

24 Troubleshooting

26 Food preparation guide

30 Recipes

49 French

3

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE

• Remove any packaging material and

promotional stickers before using the
immersion blender for the first time.

• Do not place the immersion blender

near the edge of a counter-top or table
during operation. Ensure the surface is
level, clean and free of water, flour, etc.

• When mixing liquids, especially hot

liquids with the immersion blender use
a tall container or blend small quantities
at a time to reduce spillage.

• Do not place the immersion blender on

or near a hot gas or electric burner, or
where it could touch a heated oven.

• If using the immersion blender to blend

hot food in a saucepan over heat, remove
the saucepan from the heat source and
ensure the power cord and body of
appliance are also kept away from any
heat source.

• Blades are sharp. Handle carefully.

• Take care when handling the immersion

blender, attachments and sharp cutting
blades, when emptying the bowl and
during cleaning. Remember the blades
and attachments are very sharp and
should be kept out of the reach of
children.

• Always make sure the immersion

blender is completely and properly
assembled before operating.

• Ensure the immersion blender is turned

off and the cord is unplugged from the
power outlet before attempting to attach
any of the accessories.

• Do not use attachments other than those

provided with the immersion blender.

• Do not use the whisk attachment for

anything other than its intended use.

• Do not attempt to operate the

immersion blender by any method other
than those described in this booklet.

• Do not process hot or boiling liquids

in food processor bowl – allow liquids
to cool before placing into the food
processor bowl.

• Do not operate the appliance

continuously for more than 1 minute.
Allow the motor to rest for 1 minute
between each use.

• Never mix dry, thick or heavy mixtures

for more than 30 seconds. Stop the
operation and stir the ingredients before
continuing. Allow the motor to rest for
1 minute between each use.

• When using heavy loads, the appliance

should not be operated for more than
30 seconds.

• Keep hands and utensils out of the

container while blending to prevent the
possibility of severe injury to persons
or damage to the unit. A spatula may be
used but must be used only when the
unit is not running.

• Always ensure the immersion blender

is turned off and the cord is unplugged
from the power outlet before attempting
to move the appliance, when not in
use, if left unattended and before
disassembling, cleaning or storing.

4

BREVILLE RECOMMENDS SAFETY FIRST

• Always assemble processing bowl

lid and insure it is locked into place
before use.

• If food becomes lodged around the

processing blades or in the blade guard,
release the trigger switch and unplug the
cord. Use a spatula to dislodge the food.
Do not use fingers as the blades
are sharp.

• Do not remove the immersion blender

from ingredients during operation.
Ensure the appliance is off and has
stopped before removing, to avoid
contact with moving blades or whisk.

• While processing food to reduce the risk

of severe injury to persons or damage
to the appliance a spatula may be used,
but must be used only when the food
processor is not running.

• Do not leave the immersion blender

unattended when in use.

• To protect against electric shock do not

immerse the motor body, cord or power
plug in water or any other liquid.

• Keep the appliance clean. Follow the

cleaning instructions provided in
this book.

• Do not use the immersion blender with

wet hands.

• Do not push food into the feed chute

with your fingers or other utensils.
Always use the food pusher provided.

• Keep fingers, hands, knives and other

utensils away from moving blade
and discs.

• Do not place hands or fingers in the

processing bowl of the food processor
unless the motor, processing blades
or disc have come to a complete stop.
Ensure the trigger switch has been
released to turn the motor off and the
power cord is unplugged from the power
outlet before removing the lid from the
processing bowl.

• The BSB530XL includes several

attachments. The rating for this
appliance is based on the immersion
blending leg and food processor
attachments which draw the greatest
load. Other included attachments may
draw significantly less load during
their use.

• The appliance is also fitted with a

polarised plug (one blade is wider than
the other). To reduce the risk of electric
shock this plug will fit in a polarised
outlet only one way. If the plug does not
fit, contact a qualified electrician. Do not
modify the plug in any way.

5

5

BREVILLE RECOMMENDS SAFETY FIRST

IMPORTANT SAFEGUARDS FOR
ALL ELECTRICAL APPLIANCES

• Unwind the cord fully before use.

• Do not let the cord hang over the edge of

a table or counter, touch hot surfaces or
become knotted.

• This appliance is not intended for use

by young children or infirm persons
without supervision.

• Young children should be supervised

to ensure that they do not play with
the appliance.

• It is recommended to regularly

inspect the appliance. Do not use the
appliance if power supply cord, plug
or appliance becomes damaged in any
way. Call Breville Consumer Service for
examination, adjustment and/or repair.

• For any maintenance other than

cleaning, call Breville Consumer Service.

• This appliance is for household use

only. Do not use this appliance for
anything other than its intended use.
Do not use in moving vehicles or boats.
Do not use outdoors.

BREVILLE ASSIST™ PLUG

Your Breville appliance comes with a unique
Assist™ Plug, conveniently designed with
a finger hole in the power plug for easy
and safe removal from the wall outlet. For
safety reasons it is recommended you
plug your Breville appliance directly into
its own electrical outlet on a dedicated
circuit separate from other appliances. If
the electric circuit is overloaded with other
appliances, your appliance may not function
properly. Use in conjunction with a power
strip or extension cord is not recommended.

SHORT CORD INSTRUCTIONS

Your Breville appliance is fitted with a short
power supply cord as a safety precaution to
prevent personal injury or property damage
resulting from pulling, tripping or becoming
entangled with a longer cord. Do not allow
children to use or be near this appliance
without close adult supervision. Longer
detachable power supply cords or extension
cords are not recommended but may be
used if care is exercised. If an extension cord
is used, (1) the marked electrical rating of
the cord set or extension cord should be at
least as great as the electrical rating of the
appliance, (2) the cord should be arranged
so that it will not drape over the countertop
or tabletop where it can be pulled on by
children or tripped over unintentionally
and (3) the extension cord must include a
3-prong grounding plug.

FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS

6

KNOW

your Breville product

TYPESET V1

PAge heAder.....

KNOW YOUR BREVILLE PRODUCT

A

B

IJ

K

L

M

H

N

G

O

C

D

E

F

A. Speed Control Dial
B. Easy Grip Trigger Switch
C. Motor Body
D. Processing Gear Box
E. Processing Bowl Lid
F. 6 Cup (1.6L) Processing Bowl
G. Food Pusher & Feed Chute
H. Whisk

8

I. Stainless Steel Blending Leg
J. Variable Mashing Leg
K. Micro-serrated S Blade™
L. Adjustable Slicing Disc
M. Reversible Shredding Disc
N. Storage Base
O. Spindle

NOT SHOWN

Blade Covers

TYPESET V1

ASSEMBLY & OPERATION

of your Breville product

PAge heAder.....

ASSEMBLY & OPERATION

BEFORE FIRST USE

Remove any packaging material and
promotional labels. Remove the blending
leg and wash it in warm soapy water (refer to
assembly instructions in this booklet). Rinse
and dry thoroughly.

Ensure no water remains inside the blending
leg to avoid water running into the motor
body when reattached. Disassemble and
wash the food processor bowl, bowl lid
(ensure that the removable gear box has
been removed from the lid prior to washing),
whisk, S Blade™, variable mashing leg and
adjustable slicing disc in warm soapy water,
rinse and dry thoroughly. Ensure no water
remains on the chopper bowl lid or whisk
attachment to avoid water running into the
motor body when reattached.

NOTE

The detachable blending leg,
processing bowl (without the
gearbox), S Blade™, variable mashing
leg and whisk can also be washed in
the dishwasher (top shelf only). The
whisk gear box, processor gear box
and motor body are not dishwasher
safe – see the care and cleaning
section of this booklet for cleaning
instructions of these parts.

This immersion blender is a versatile
appliance that can be attached to:

• The stainless steel blending leg – for use

as an immersion blender.

• The food processor bowl with S Blade™,

adjustable slicing disc, reversible
shredding disc - for use as a mini
food processor.

• The variable mashing leg – for use in

mashing fruits and vegetables.

• The whisk attachment – for use as a

hand whisk.

TO ATTACH THE BLENDING LEG

Hold the blending leg with the blades down,
and align the top end of the blending leg
with the corresponding end of the motor
body and push until the blending leg clicks
and locks onto the motor body.

Always ensure blending leg is dry, and no
water left inside, before reattaching.

USING AS AN IMMERSION BLENDER

Ensure the blending leg is assembled to the
motor body as detailed above.

1. Place food to be processed into a jug

(or a sufficiently large mixing bowl or
saucepan). The jug should be only be
½ full or less when blending liquids
or when making a puree of fruit
and/or vegetables.

2. Insert the plug into a 110/120Vpower

outlet and turn the power on.

3. By turning the dial at the top of motor

body, select a speed from 1 to 15.

NOTE

If selecting a higher speed, it is
recommended that you start on
a slow speed and then increase to
high speed to avoid splattering and
over-processing.

10

PAge heAder.....

ASSEMBLY & OPERATION

4. Place the blending leg as deeply as

possible into the jug and press the
trigger switch to turn the immersion
blender on. The button must be held for
the required duration of operation.

5. Work through the ingredients in

the jug with a gentle raising and
lowering motion.

6. Turn the motor off by releasing the

trigger switch.

7. Ensure the motor has completely

stopped before lifting the blender out of
the jug.

8. When processing has finished remove

the power plug.

TO DETACH THE BLENDING LEG

Ensure the trigger switch is released and
the appliance is unplugged. Hold the motor
body with one hand, and using thumb and
finger of the other hand, press on the two
EJECT buttons on either side of the motor
body. Pull the motor body away from the
blending leg to detach.

RECOMMENDATIONS WHEN USING
AS AN IMMERSION BLENDER

• The immersion blender blends foods

and liquids rapidly, therefore it is easy
to over process. Remember when using
the blending leg to stop the immersion
blender and check food throughout the
operation.

• Allow food to cool before blending.

• The stainless steel blending leg allows

for hot food to be processed directly
in the saucepan. This makes blending
soups and sauces very easy.

• For safety reasons remove saucepan

away from the heat before processing.

• Ensure the body of the appliance and

power cord are kept away from any
heat source.

• When pureeing and blending, cut food

into uniform sizes. This will ensure
smooth and consistent results.

• Warm all liquids to be added to soups

and purees, this will ensure even
blending.

• Do not operate the appliance

continuously for more than 1 minute.
Allow the motor to rest for 1 minute
between each use.

If food becomes lodged around the
processing blade or in the blade guard,
follow the following safety instructions:

1. Release the trigger switch to power off

and unplug the cord.

2. Use a spatula to carefully dislodge the

food. Do not use fingers as the blades
are sharp.

3. After the food has been removed and

blades are clear, plug the appliance back
into the power supply and continue
blending.

11

PAge heAder.....

ASSEMBLY & OPERATION

USING THE FOOD
PROCESSOR BOWL

Attaching gearbox to food processing
bowl lid

1. Place the gearbox into the food

processor lid, it will click into place.

To attach the food processing bowl, food
processor attachments and lid

1. Remove the food processing bowl

from the storage unit and place onto a
counter-top or table ensuring that the
surface is clean and level.

2. Choose one of the following food

processor attachments:

a) S Blade™
b) Adjustable slicer
c) Reversible shredder

3. There is a common spindle that is

used across all of the three food
processor attachments.

When using the reversible shredder

1. Place the spindle into the center of the

food processing bowl.

2. To attach the motor click it into place on

the gearbox.

12

CAUTION

Caution should be taken when
handling the shredding disc.

2. Holding the reversible shredding disc,

notice that there is a side for coarse
shredding and a side for fine shredding.
Place the side you require up. Align the
hole in the center of the disc with the
spindle and ensure that it is pushed
down firmly.

PAge heAder.....

ASSEMBLY & OPERATION

3. Place the processing bowl lid into

position and ensure that it is on correctly
aligned and locked into place.

2. The adjustable slicing disc has 19

precise settings. To adjust the settings
hold the adjustable slicing disc by
the edge (on the opposite side of the
cutting blade) with one hand and turn
the rotating collar on the bottom of the
disc to the desired setting with the other
hand.

3. Place the adjustable slicing disc onto the

spindle. Ensure that it is pushed down
into place.

When using the adjustable slicer

1. Place the spindle into the center of the

food processing bowl.

CAUTION

Caution should be taken when
handling the adjustable slicing disc.

4. Place the processing bowl lid into

position and ensure that it is on correctly
aligned and locked into place.

13

PAge heAder.....

ASSEMBLY & OPERATION

When using the S Blade™

1. Using care, hold the S Blade™ in one

hand, with the other hand, place the
spindle through the center of the S
Blade™ from underneath. The blade
should self-locate at the base of the
spindle. The blade will sit loosely on the
spindle but will lock into place during
processing.

CAUTION

Caution should be taken when
handling the S Blade™ as the blades
are extremely sharp.

2. Place the S Blade™ and spindle into the

center of the food processing bowl.

3. Align and lock the processing bowl lid

into place.

Once the blade or disc has been selected
for the food processor and you have
assembled as listed in the previous
instructions, you can now process food.

Place the ingredients inside the processing
bowl or in the feed chute (depending on the
task). Do not exceed the maximum (MAX)
marking. Insert the gear box into the lid of
the food processor.

NOTE

Always place the S Blade™ into the
food processor prior to placing the
food into the food processor. If using
the adjustable slicer or the reversible
shredding disc, you are able to
assemble the processor before adding
ingredients to the bowl. Ingredients
used with these discs will need to
be added through the small or large
feed chute. Some foods, such as nuts,
can stop the S Blade™ from engaging
the built in safety mechanism. If you
have difficulty closing the lid with
ingredients such as these we advise
to load them through the feed chute
after the processor has been fully
assembled.

14

PAge heAder.....

ASSEMBLY & OPERATION

TO USE THE FOOD PROCESSOR

For food preparation tips and recipes refer to
the recipe section of this booklet.

1. Insert the plug into a 110/120V outlet.

2. Select a speed between 1–15 on the

speed control dial.

3. Press the trigger switch to turn

the appliance on and start the
processing action.

5. When processing has finished turn the

motor off by releasing the trigger switch
and remove the power plug.

6. Detach the motor from the gear box

and remove the lid from the bowl (refer
to instructions). Carefully remove the
food processing disc or S Blade™ and
use a spatula to remove any excess food
from the discs or blades and to remove
processed food from the bowl.

NOTE

When processing food through the
feed chute(s) you must keep pressing
the trigger switch in order to keep the
motor on.

TO DETACH THE FOOD
PROCESSING BOWL AND LID

Ensure the trigger switch is released and the
appliance is unplugged.

Hold the motor body with one hand and
using thumb and finger of the other hand,
press on the two EJECT buttons on either
side of the motor body. Pull the motor
body away from the processing bowl
gearbox to detach.

4. Feed the food through the feed chute

of the food processor, using the food
pusher to push it down.

15

PAge heAder.....

ASSEMBLY & OPERATION

TO DETACH THE GEARBOX
FROM THE LID

Lift the gear box up from the processing
bowl lid.

RECOMMENDATIONS WHEN USING
THE IMMERSION BLENDER WITH
THE PROCESSING BOWL

• Do not operate the immersion blender

when the processing bowl is empty.

• The bottom of the processing bowl

features a anti-slip rubber rim around
the bottom of the bowl. This keeps the
processing bowl stable, however it is
recommended during processing to hold
the motor body with one hand and the
processing bowl and lid with the other.

• When processing, cut food into uniform

sizes to ensure quicker, even and more
consistent results.

• The immersion blender blends foods

and liquids rapidly, therefore it is easy to
over process. Remember to check food
throughout the operation.

CAUTION

DO NOT process hard foods such as
ice, coffee, cereal or chocolate in lumps
in the processing bowl, as damage to
the blades may result.

DO NOT process boiling or hot foods in
the processing bowl.

NEVER remove the blades from the
bowl before processing is completed.

16

PAge heAder.....

ASSEMBLY & OPERATION

BEFORE FIRST USE

Remove any packaging material and
promotional labels. Wash blade and two
parts of the mashing leg before use.

CAUTION

Never immerse the motor body or
gearbox in water or any other liquid.

ASSEMBLY OF THE MASHING LEG

1. Hold the outer leg and insert the

gearbox making sure ALIGN arrows are
aligned.

2. Hold both outer leg and gearbox firmly

with one hand and insert inner leg until
it clicks into place.

3. Holding gearbox twist outer leg to lock.

4. Align the mashing leg with the motor

body and push the two parts together
until it clicks.

5. Place blade on underside of the mashing

head. To lock the blade rotate in a
counter-clockwise direction. Blade will
not attach if the leg is not attached to
the motor body.

17

PAge heAder.....

ASSEMBLY & OPERATION

TO USE THE VARIABLE
MASHING LEG

For food preparation tips and recipes refer
to the recipes section. Ensure the variable
mashing leg is completely and properly
assembled.

1. Place food to be mashed into a blending

jug or a sufficiently large mixing bowl
or container.

2. Insert the plug into a 110/120V power

outlet.

3. Select the desired setting on the variable

mashing leg.

4. Select a high speed on the speed control

dial of the motor.

5. Place the variable mashing leg into

ingredients and press the trigger switch
to turn the mashing leg on.

6. Move the mashing leg through the

ingredients with a gentle raising and
lowering action until desired texture is
achieved.

7. Turn the motor off by releasing the

trigger switch before lifting the mashing
leg out of the bowl and remove the
power plug.

TO DETACH THE VARIABLE
MASHING LEG

Ensure the trigger switch is released and the
appliance is unplugged.

Hold the motor body with one hand, and,
using thumb and finger of the other hand,
press on the two EJECT buttons on either
side of the motor body. Pull the motor body
away from the mashing leg to detach.

RECOMMENDATIONS WHEN USING
WITH THE VARIABLE MASHING LEG

• Release the trigger switch and ensure

the mashing leg has completely stopped
turning before removing the mashing
leg from the food during operation.

• Place the mixing bowl on a damp cloth

during mashing. This will keep the
mixing bowl stable.

USING AS A WHISK

Remove blending leg from motor body
(follow the instructions “To detach the
blending leg”).

Align the top end of the whisk gearbox with
the corresponding end of the motor body
and push until the gearbox clicks into place.
Align the shaft of the whisk with the hole in
the gearbox and push until the whisk clicks
and locks into place.

18

PAge heAder.....

ASSEMBLY & OPERATION

TO USE THE WHISK

For food preparation tips and recipes refer
to the recipes section. Ensure the whisk is
completely and properly assembled.

1. Place food to be processed into a

blending jug or a sufficiently large
mixing bowl or container.

2. Insert the plug into a 110/120V power

outlet.

3. Select a speed between 1–15 on the

speed control dial.

4. Place the whisk into ingredients

and press the trigger switch to start
whisking.

5. Move the whisk through the ingredients

with a gentle raising and lowering action
until desired texture is achieved.

6. Turn the motor off by releasing the

trigger switch before lifting the whisk
out of the bowl remove the power plug.

TO DETACH THE WHISK

Ensure the trigger switch is released and
the appliance is unplugged. Hold the motor
body with one hand, and, using thumb and
finger of the other hand, press on the two
EJECT buttons on either side of the motor
body. Pull the motor body away from the
whisk to detach.

RECOMMENDATIONS WHEN USING
THE WHISK ATTACHMENT

• Do not allow the whisk to touch the

bottom or sides of mixing bowl while
the appliance is in operation, as this may
damage the whisk.

• To incorporate air into the ingredients

when whisking, use a deep and wide
enough container for the amount of
ingredients and move the whisk with a
gentle raising and lowering action.

• Release the trigger switch and ensure

the whisk has completely stopped
turning before removing the whisk from
the food during operation.

• Place the mixing bowl on a damp cloth

during whisking. This will keep the
mixing bowl stable.

• Always use fresh chilled cream and

fresh eggs at room temperature to
achieve greater and more stable volume
when whisking.

• Always ensure the whisk and mixing

bowl are completely clean and free of fat
before whisking egg whites.

• It is recommended to use the highest

speed when whisking egg whites
and cream.

19

CARE, CLEANING

& STORAGE

of your Breville product

TYPESET V1

CARE, CLEANING & STORAGE

MOTOR BODY

To remove any food residue wipe the motor
body and cord with a damp cloth only.
Do not use abrasive cleaners or steel wool.
Never immerse the motor body in water or
any other liquid. Do not place motor body
in dishwasher.

BLENDING LEG

Before cleaning remove the plug from
the power outlet. Remove the motor body
from the stainless steel blending leg. The
stainless steel blending leg can be hand
washed in hot soapy water, rinsed and dried
thoroughly after each use. Alternatively,
the blending leg can also be washed in the
dishwasher. (TOP SHELF ONLY)
Do not use abrasive cleaners or steel wool.

QUICK WASH: Between each processing
task, with the motor body attached place
the stainless steel blending leg and blade
assembly only in to a jug of water and press
the trigger switch to turn on for 5 seconds.
This will remove any food on the blade and
leg and allow you to continue onto the next
processing task.

The food processing bowl, bowl lid,
S Blade™ and processing discs should be
hand washed in hot soapy water, rinsed
and dried thoroughly after each use.
Alternatively, the food processing bowl,
bowl lid, S Blade™, adjustable slicing disc
and reversible shredder can also be washed
in the dishwasher (TOP SHELF ONLY). The
S Blade™ comes with a cover for your safety.
This cover can be used on the blade in the
dishwasher. Do not use abrasive cleaners or
steel wool.

CARE & CLEANING OF THE
GEARBOX

The gearbox should always be removed from
the lid prior to any cleaning.

The gearbox simply lifts out of the lid by
pulling it up.

FOOD PROCESSING BOWL, FOOD
PROCESSING BOWL LID, S BLADE™,
ADJUSTABLE SLICING DISC &
REVERSIBLE SHREDDER

Before cleaning remove the plug from the
power outlet. Remove the motor body from
the food processing bowl lid and gear box.
Remove the food processing bowl lid and
S Blade™ or processing disc from the food
processing bowl.

NOTE

The processing bowl lid is dishwasher
safe. Simply remove the removable
gear box from the lid prior to placing
in the dishwasher.

NOTE

The gear box is not dishwasher safe
and should never be immersed in
liquid at all.

To clean the gearbox, remove from the
lid and wipe down with a damp cloth
only. Do not use abrasive cleansers or
steel wool.

21

PAge heAder.....

CARE, CLEANING & STORAGE

VARIABLE MASHING LEG

Before cleaning remove the plug from the
power outlet. Remove the motor body and
mashing leg gearbox from the mashing leg.
The mashing leg can be hand washed in hot
soapy water, rinsed and dried thoroughly
after each use.

TO DISASSEMBLE THE
VARIABLE MASHING LEG.

1. Ensure the motor is unplugged and

attached to the mashing leg. Remove the
mashing blade that is found under the
base of the leg by turning it clockwise.

2. Disassemble the gear box from motor

body, then turn the mashing leg to align
and remove the inner and outer legs
from the gear box together.

3. Lift the outer leg up to separate from the

inner leg.

Both of the legs can now be washed in
hot soapy water, then rinsed and dried
thoroughly. Alternatively, the mashing leg
can be washed in the dishwasher
(TOP SHELF ONLY).

CAUTION

Do not use abrasive cleaners or steel
wool.

NOTE

Mashing leg gear box is not
dishwasher safe.

22

PAge heAder.....

CARE, CLEANING & STORAGE

WHISK

Before cleaning remove the plug from the
power outlet. Remove the motor body from
the whisk and the gearbox from the whisk.
The whisk can be hand washed in hot soapy
water, rinsed and dried thoroughly after
each use. Alternatively, the whisk can also
be washed in the dishwasher.
(TOP SHELF ONLY)
Do not use abrasive cleaners or steel wool.
Whisk gear box is not dishwasher safe.

STORAGE

Before storage remove the plug from the
power outlet. Ensure the appliance is clean
and completely dry.
Insert assembled S Blade™ and spindle
into the processing bowl, then place the
reversible shredder on the spindle. Align
and lock the processing bowl lid to the
processing bowl and place processing
bowl onto the storage unit with all of the
accessories on the built in accessory holders.

NOTE

The adjustable slicing disc is stored
under the food processing bowl, make
sure that the adjustable blade is set to
STORAGE POSITION.

23

TYPESET V1

TROUBLESHOOTING

PAGE HEADER.....TROUBLESHOOTING

Food may stuck underneath the S Blade™ preventing the

PROBLEM SOLUTION

Blades don’t turn when
processing.

Unable to lock lid
into place.

Gear box in lid jumps out
of lid when processing.

Mashing leg leg won’t
attach onto mashing leg
gear box.

Blades won’t remove
from mashing leg.

Shredding disc slows
down when in use.

Processing bowl does not
sit flat on storage base.

• May be too much food in bowl; reduce quantity.

• Pieces of food, such as meat are too large, reduce size.

• Spindle may be out of position. Remove lid, straighten

spindle as vertical as possible and reposition lid.

•

lid from being locked into place. Food such as nuts can
be loaded through the feed chute.

• Replace gear box and ensure that the control grip is

held vertically and firmly.

• Ensure mashing leg and gear box arrow graphics are

vertically aligned. Twist mashing leg counterclockwise
to lock for use.

• Mashing leg should still be assembled to the gear box

assembly and to the unplugged motor body.
Rotate blades clockwise.

• Shredding has exceeded Max level. Empty bowl and

continue to shred.

• Too much force is being used when shredding. Reduce

force when pushing.

• Ensure adjustable slicing disc is set to ‘Storage Position’

Motor sounds like it is
not able to process load.

• Speed may not be correct. Refer to processing guide for

correct speeds.

25

TYPESET V1

FOOD PREPARATION

CHART

FOOD PREPARATION CHART

FOOD TYPE ATTACHMENT

TYPE

DISK TYPE SPEED

Carrot Food Processor Shredder

fine

Food Processor Shredder

coarse

Food Processor Adjustable

slicer

Zucchini Food Processor Shredder

fine

Food Processor Shredder

coarse

Food Processor Adjustable

slicer

Cucumber Food Processor Adjustable

slicer

Tomato Food Processor Adjustable

slicer

Cabbage Food Processor Adjustable

slicer

Food Processor Shredder

coarse

Leek Food Processor Shredder

slicer

Onion Food Processor Adjustable

slicer

Food Processor S Blade™ 15 Cut in

SETTING

BLADE
THICKNESS

RECOMMENDED
QUANTITY

9–13 1–2 carrots at a time,

depending on size

9–13

9–13

11–15

1 –6mm 1 –2 carrots at a time

1–2 carrots at a time,
depending on size

depending on size

1–2 zucchini at a
time, depending on
size

11–15

1–2 zucchini at a
time, depending on
size

9–13

1–6mm 1–2 zucchini at a

time, depending on
size

9–13

2–5mm 1–2 cucumber at a

time, depending on
size

9–11

9–11

11 –15

9–13

9–13 2–6mm Cut in half

4–6mm Use firm tomatoes

2–6mm Cut to size to fit

chute

Cut to size to fit
chute

2–6mm White part only

to fit in chute

1

⁄4 for pulse

processing

Chicken
(boneless
breast/thigh
fillets)

Food Processor S Blade™ 15 1.5lb (700g) max cut

into 1 inch cubes

27

FOOD PREPARATION CHART

FOOD TYPE ATTACHMENT

TYPE

DISK TYPE SPEED

SETTING

BLADE
THICKNESS

RECOMMENDED
QUANTITY

Lean Beef Food Processor S Blade™ 15 1.5lb (700g)

max cut into 1 inch
cubes

Lean Pork Food Processor S Blade™ 15 1.5lb (700g)

max cut into 1 inch
cubes

Fish Fillets Food Processor S Blade™ 15 700g max cut into

1 inch cubes

Cheddar Food Processor Shredder

15 Must be well chilled

fine

Food Processor Shredder

15 Must be well chilled

coarse

Mozzarella Food Processor Shredder

coarse

15 Place in freezer for

20 minutes before
grating

Parmesan Food Processor Shredder

fine

Food Processor Shredder

Coarse

Milkshakes,

Blending Leg 11–15 Use chilled milk.
smoothies,
fruit

15 Must be well chilled;

rind removed

15 Must be well chilled;

rind removed

Blend for 30 seconds

at a time
frappes,
cocktails

Soups, baby
food

Blending Leg 11–15 Blend until smooth,

checking desired

consistency every

30 seconds

Ice Blending Leg– Do

not use Processing

15 Crush ice for 20–30

seconds

Bowl

Cream Whisk 11–15 Whisk for 1 minute

at a time, rest for

1 minute between

each use

28

PAge heAder.....

FOOD PREPARATION CHART

FOOD TYPE ATTACHMENT

TYPE

DISK TYPE SPEED

SETTING

BLADE
THICKNESS

RECOMMENDED

QUANTITY

Nuts Food Processor S Blade™ 15 9oz (250g) for 30

seconds at time until

desired consistency

is achieved. Wait 30

seconds between

each interval.

Bread
Crumbs

Cookie

Food Processor S Blade™ 15 2–3 slices cut into

quarters

Food Processor S Blade™ 15 9oz (250g) max

Crumbs

Cooked
Fruits or

Variable Mashing
leg

15 Mash to desired

consistency
Vegetables

29

RECIPES

TYPESET V1