Breville BSB530XL Instruction Handbook
the All In One
™
Instruction Book - BSB530XL
BSB530XL_IB_C16.indd 1 7/11/2016 1:45 PM
Contents
IMPORTANT
SAFEGUARDS
2 Breville recommends safety first
8 Components
9 Functions
18 Care & Cleaning
20 Troubleshooting
21 Food preparation guide
23 French
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions.
READ ALL
INSTRUCTIONS BEFORE
USE AND SAVE FOR
FUTURE REFERENCE
• Remove any packaging
material and promotional
stickers before using the
immersion blender for the
first time.
• Do not place the
immersion blender near
the edge of a counter-top
or table during operation.
Ensure the surface is level,
clean and free of water,
flour, etc.
• When mixing liquids,
especially hot liquids with
the immersion blender
use a tall container or
blend small quantities at a
time to reduce spillage.
• Do not place the
immersion blender on or
near a hot gas or electric
burner, or where it could
touch a heated oven.
2
BSB530XL_IB_C16.indd 2 7/11/2016 1:45 PM
• If using the immersion
blender to blend hot food
in a saucepan over heat,
remove the saucepan
from the heat source and
ensure the power cord and
body of appliance are also
kept away from any heat
source.
• Blades are sharp. Handle
carefully.
• Ensure the immersion
blender is turned off and
the cord is unplugged
from the power outlet
before attempting
to attach any of the
accessories.
• Do not use attachments
other than those provided
with the immersion
blender.
• Take care when handling
the immersion blender,
attachments and sharp
cutting blades, when
emptying the bowl
and during cleaning.
Remember the blades
and attachments are
very sharp and should be
kept out of the reach of
children.
• Always make sure the
immersion blender is
completely and properly
assembled before
operating.
• Do not use the whisk
attachment for anything
other than its intended
use.
• Do not attempt to operate
the immersion blender
by any method other than
those described in this
booklet.
• Do not process hot or
boiling liquids in food
processor bowl – allow
liquids to cool before
placing into the food
processor bowl.
• Do not operate the
appliance continuously for
more than 1 minute. Allow
the motor to rest for 1
minute between each use.
3
BSB530XL_IB_C16.indd 3 7/11/2016 1:45 PM
• Never mix dry, thick or
heavy mixtures for more
than 30 seconds. Stop
the operation and stir
the ingredients before
continuing. Allow the
motor to rest for
1 minute between each
use.
• When using heavy loads,
the appliance should not
be operated for more than
30 seconds.
• Always assemble
processing bowl
lid and insure it is locked
into place before use.
• If food becomes lodged
around the processing
blades or in the blade
guard, release the trigger
switch and unplug the
cord. Use a spatula to
dislodge the food. Do not
use fingers as the blades
are sharp.
• Keep hands and utensils
out of the container while
blending to prevent the
possibility of severe injury
to persons or damage to
the unit. A spatula may
be used but must be used
only when the unit is not
running.
• Always ensure the
immersion blender is
turned off and the cord
is unplugged from the
power outlet before
attempting to move the
appliance, when not in
use, if left unattended and
before disassembling,
cleaning or storing.
4
• Do not remove the
immersion blender
from ingredients during
operation. Ensure the
appliance is off and has
stopped before removing,
to avoid contact with
moving blades or whisk.
• While processing food to
reduce the risk of severe
injury to persons or
damage to the appliance a
spatula may be used, but
must be used only when
the food processor is not
running.
BSB530XL_IB_C16.indd 4 7/11/2016 1:45 PM
• Do not leave the
immersion blender
unattended when in use.
• To protect against electric
shock do not immerse the
motor body, cord or power
plug in water or any other
liquid.
• Keep the appliance clean.
Follow the cleaning
instructions provided in
this book.
• Do not use the immersion
blender with wet hands.
• Do not push food into
the feed chute with your
fingers or other utensils.
Always use the food
pusher provided.
• Keep fingers, hands,
knives and other utensils
away from moving blade
and discs.
• Do not place hands or
fingers in the processing
bowl of the food
processor unless the
motor, processing blades
or disc have come to a
complete stop. Ensure
the trigger switch has
been released to turn the
motor off and the power
cord is unplugged from
the power outlet before
removing the lid from the
processing bowl.
• The BSB530XL includes
several attachments. The
rating for this appliance is
based on the immersion
blending leg and food
processor attachments
which draw the greatest
load. Other included
attachments may draw
significantly less load
during their use.
5
BSB530XL_IB_C16.indd 5 7/11/2016 1:45 PM
• The appliance is also
fitted with a polarised
plug (one blade is wider
than the other). To reduce
the risk of electric shock
this plug will fit in a
polarised outlet only one
way. If the plug does not
fit, contact a qualified
electrician. Do not modify
the plug in any way.
Do not modify the plug in
any way.
• Do not let the cord
hang over the edge of a
table or counter, touch
hot surfaces or become
knotted.
• This appliance is not
intended for use by young
children or infirm persons
without supervision.
IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES
• Unwind the cord fully
before use.
• This appliance has a
polarized plug (one blade
is wider than the other).
To reduce the risk of
electric shock, this plug
will fit in a polarized outlet
only one way. If the plug
does not fit fully in the
outlet, reverse the plug. If
it still does not fit, contact
a qualified electrician.
• Young children should be
supervised
to ensure that they do not
play with
the appliance.
• It is recommended to
regularly inspect the
appliance. Do not use the
appliance if power supply
cord, plug or appliance
becomes damaged in
any way. Call Breville
Consumer Support for
examination, adjustment
and/or repair.
• For any maintenance
other than cleaning,
call Breville Consumer
Support.
6
BSB530XL_IB_C16.indd 6 7/11/2016 1:45 PM
• This appliance is for
household use only. Do
not use this appliance
for anything other than
its intended use. Do not
use in moving vehicles
or boats. Do not use
outdoors.
®
BREVILLE ASSIST
PLUG
Your Breville appliance
comes with a unique
®
Assist
Plug, conveniently
designed with a finger hole
to ease removal from the
power outlet.
SHORT CORD
INSTRUCTIONS
Your Breville appliance
is fitted with a short
power supply cord to
reduce personal injury or
property damage resulting
from pulling, tripping or
becoming entangled with a
longer cord.
If an extension cord is
used, (1) the marked
electrical rating of the
cord set or extension cord
should be at least as great
as the electrical rating of
the appliance, (2) the cord
should be arranged so
that it will not drape over
the countertop or tabletop where it can be pulled
on by children or tripped
over unintentionally and
(3) the extension cord
must include a 3-prong
grounding plug.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
7
BSB530XL_IB_C16.indd 7 7/11/2016 1:45 PM
Components
A
B
K
L
A. Speed Control Dial
B. Easy Grip Trigger Switch
C. Motor Body
D. Processing Gear Box
E. Processing Bowl Lid
F. 6 Cup (1.6L) Processing Bowl
G. Food Pusher & Feed Chute
H. Whisk
I. Stainless Steel Blending Leg
M
IJ
H
N
J. Variable Mashing Leg
K. Micro-serrated S Blade™
L. Adjustable Slicing Disc
M. Reversible Shredding Disc
N. Storage Base
O. Spindle
NOT SHOWN
Blade Covers
G
O
C
D
E
F
8
BSB530XL_IB_C16.indd 8 7/11/2016 1:45 PM
Functions
BEFORE FIRST USE
Remove any packaging material and
promotional labels. Remove the blending
leg and wash it in warm soapy water (refer to
assembly instructions in this booklet). Rinse
and dry thoroughly.
Ensure no water remains inside the blending
leg to avoid water running into the motor body
when reattached. Disassemble and wash the
food processor bowl, bowl lid (ensure that the
removable gear box has been removed from
the lid prior to washing), whisk, S Blade™,
variable mashing leg and adjustable slicing
disc in warm soapy water, rinse and dry
thoroughly. Ensure no water remains on
the chopper bowl lid or whisk attachment to
avoid water running into the motor body
when reattached.
NOTE
The detachable blending leg, processing
bowl (without the gearbox), S Blade™, variable
mashing leg and whisk can also be washed in
the dishwasher (top shelf only). The whisk gear
box, processor gear box and motor body are
not dishwasher safe – see the care and cleaning
section of this booklet for cleaning instructions
of these parts.
This immersion blender is a versatile
appliance that can be attached to:
• The stainless steel blending leg – for use as
an immersion blender.
• The food processor bowl with S Blade™,
adjustable slicing disc, reversible shredding
disc - for use as a mini food processor.
• The variable mashing leg – for use in
mashing fruits and vegetables.
• The whisk attachment – for use as a
hand whisk.
TO ATTACH THE BLENDING LEG
Hold the blending leg with the blades down,
and align the top end of the blending leg with
the corresponding end of the motor body and
push until the blending leg clicks and locks
onto the motor body.
Always ensure blending leg is dry, and no
water left inside, before reattaching.
USING AS AN IMMERSION BLENDER
Ensure the blending leg is assembled to the
motor body as detailed above.
1. Place food to be processed into a jug (or a
sufficiently large mixing bowl or saucepan).
The jug should be only be ½ full or less
when blending liquids or when making a
puree of fruit and/or vegetables.
2. Insert the plug into a 110/120V power
outlet and turn the power on.
3. By turning the dial at the top of motor body,
select a speed from 1 to 15.
NOTE
If selecting a higher speed, it is recommended
that you start on a slow speed and then
increase to high speed to avoid splattering and
over-processing.
4. Place the blending leg as deeply as possible
into the jug and press the trigger switch
to turn the immersion blender on. The
button must be held for the required
duration of operation.
5. Work through the ingredients in the jug
with a gentle raising and lowering motion.
9
BSB530XL_IB_C16.indd 9 7/11/2016 1:45 PM
6. Turn the motor off by releasing the trigger
switch.
7. Ensure the motor has completely stopped
before lifting the blender out of the jug.
8. When processing has finished remove the
power plug.
TO DETACH THE BLENDING LEG
Ensure the trigger switch is released and the
appliance is unplugged. Hold the motor body
with one hand, and using thumb and finger
of the other hand, press on the two EJECT
buttons on either side of the motor body.
Pull the motor body away from the blending
leg to detach.
RECOMMENDATIONS WHEN USING
AS AN IMMERSION BLENDER
• The immersion blender blends foods and
liquids rapidly, therefore it is easy to over
process. Remember when using the blending
leg to stop the immersion blender and check
food throughout the operation.
• Allow food to cool before blending.
• The stainless steel blending leg allows for hot
food to be processed directly in the saucepan.
This makes blending soups and sauces very
easy.
• For safety reasons remove saucepan away
from the heat before processing.
• Ensure the body of the appliance and power
cord are kept away from any
heat source.
• When puréeing and blending, cut food into
uniform sizes. This will ensure smooth and
consistent results.
• Warm all liquids to be added to soups and
purées, this will ensure even blending.
• Do not operate the appliance continuously
for more than 1 minute. Allow the motor to
rest for 1 minute between each use.
If food becomes lodged around the processing
blade or in the blade guard, follow the
following safety instructions:
1. Release the trigger switch to power off and
unplug the cord.
2. Use a spatula to carefully dislodge the food.
Do not use fingers as the blades are sharp.
3. After the food has been removed and blades
are clear, plug the appliance back into the
power supply and continue blending.
USING THE FOOD
PROCESSOR BOWL
Attaching gearbox to food processing
bowl lid
1. Place the gearbox into the food processor
lid, it will click into place.
10
BSB530XL_IB_C16.indd 10 7/11/2016 1:45 PM
2. To attach the motor click it into place on
the gearbox.
To attach the food processing bowl, food
processor attachments and lid
1. Remove the food processing bowl from the
storage unit and place onto a counter-top
or table ensuring that the surface is clean
and level.
2. Choose one of the following food processor
attachments:
- S Blade™
- Adjustable slicer
- Reversible shredder
3. There is a common spindle that is used
across all of the three food processor
attachments.
2. Holding the reversible shredding disc,
notice that there is a side for coarse
shredding and a side for fine shredding.
Place the side you require up. Align the hole
in the center of the disc with the spindle and
ensure that it is pushed down firmly.
3. Place the processing bowl lid into position
and ensure that it is on correctly aligned
and locked into place.
When using the reversible shredder
1. Place the spindle into the center of the food
processing bowl.
When using the adjustable slicer
1. Place the spindle into the center of the food
processing bowl.
CAUTION
Caution should be taken when handling the
shredding disc.
CAUTION
Caution should be taken when handling the
adjustable slicing disc.
11
BSB530XL_IB_C16.indd 11 7/11/2016 1:45 PM
2. The adjustable slicing disc has 19 precise
settings. To adjust the settings hold the
adjustable slicing disc by the edge (on the
opposite side of the cutting blade) with one
hand and turn the rotating collar on the
bottom of the disc to the desired setting
with the other hand.
3. Place the adjustable slicing disc onto the
spindle. Ensure that it is pushed down
into place.
When using the S Blade™
1. Using care, hold the S Blade™ in one hand,
with the other hand, place the spindle
through the center of the S Blade™ from
underneath. The blade should self-locate
at the base of the spindle. The blade will
sit loosely on the spindle but will lock into
place during processing.
CAUTION
Caution should be taken when handling the
S Blade™ as the blades are extremely sharp.
2. Place the S Blade™ and spindle into the
center of the food processing bowl.
3. Align and lock the processing bowl lid
into place.
4. Place the processing bowl lid into position
and ensure that it is on correctly aligned
and locked into place.
12
BSB530XL_IB_C16.indd 12 7/11/2016 1:45 PM
Once the blade or disc has been selected for
the food processor and you have assembled as
listed in the previous instructions, you can now
process food.
Place the ingredients inside the processing
bowl or in the feed chute (depending on the
task). Do not exceed the maximum (MAX)
marking. Insert the gear box into the lid of the
food processor.
NOTE
Always place the S Blade™ into the food
processor prior to placing the food into the
food processor. If using the adjustable slicer
or the reversible shredding disc, you are able
to assemble the processor before adding
ingredients to the bowl. Ingredients used with
these discs will need to be added through the
small or large feed chute. Some foods, such as
nuts, can stop the S Blade™ from engaging the
built in safety mechanism. If you have difficulty
closing the lid with ingredients such as these
we advise to load them through the feed chute
after the processor has been fully assembled.
TO USE THE FOOD PROCESSOR
1. Insert the plug into a 110/120V outlet.
2. Select a speed between 1–15 on the speed
control dial.
3. Press the trigger switch to turn the
appliance on and start the processing
action.
4. Feed the food through the feed chute of the
food processor, using the food pusher to
push it down.
13
BSB530XL_IB_C16.indd 13 7/11/2016 1:45 PM
5. When processing has finished turn the
motor off by releasing the trigger switch
and remove the power plug.
6. Detach the motor from the gear box and
remove the lid from the bowl (refer to
instructions). Carefully remove the food
processing disc or S Blade™ and use a
spatula to remove any excess food from the
discs or blades and to remove processed
food from the bowl.
NOTE
When processing food through the feed
chute(s) you must keep pressing the trigger
switch in order to keep the motor on.
TO DETACH THE GEARBOX
FROM THE LID
Lift the gear box up from the processing
bowl lid.
TO DETACH THE FOOD PROCESSING
BOWL AND LID
Ensure the trigger switch is released and the
appliance is unplugged.
Hold the motor body with one hand and using
thumb and finger of the other hand, press on
the two EJECT buttons on either side of the
motor body. Pull the motor body away from the
processing bowl gearbox to detach.
RECOMMENDATIONS WHEN USING
THE IMMERSION BLENDER WITH
THE PROCESSING BOWL
• Do not operate the immersion blender when
the processing bowl is empty.
• The bottom of the processing bowl features
a anti-slip rubber rim around the bottom of
the bowl. This keeps the processing bowl
stable, however it is recommended during
processing to hold the motor body with one
hand and the processing bowl and lid with
the other.
• When processing, cut food into uniform sizes
to ensure quicker, even and more consistent
results.
• The immersion blender blends foods and
liquids rapidly, therefore it is easy to over
process. Remember to check food throughout
the operation.
CAUTION
• DO NOT process hard foods such as ice,
coffee, cereal or chocolate in lumps in the
processing bowl, as damage to the blades
may result.
• DO NOT process boiling or hot foods in the
processing bowl.
• NEVER remove the blades from the bowl
before processing is completed.
14
BSB530XL_IB_C16.indd 14 7/11/2016 1:45 PM
BEFORE FIRST USE
Remove any packaging material and
promotional labels. Wash blade and two
parts of the mashing leg before use.
CAUTION
Never immerse the motor body or gearbox
in water or any other liquid.
ASSEMBLY OF THE MASHING LEG
1. Hold the outer leg and insert the gearbox
making sure ALIGN arrows are aligned.
2. Hold both outer leg and gearbox firmly with
one hand and insert inner leg until it clicks
into place.
3. Holding gearbox twist outer leg to lock.
4. Align the mashing leg with the motor
body and push the two parts together until
it clicks.
5. Place blade on underside of the mashing
head. To lock the blade rotate in a counterclockwise direction. Blade will not attach if
the leg is not attached to the motor body.
15
BSB530XL_IB_C16.indd 15 7/11/2016 1:45 PM
Loading...