Breville BSB530BSS Instruction Handbook

TYPESET V1

the All In One

Instruction Booklet

™

BSB530

TYPESET V1

CONGRATULATIONS

on the purchase of your Breville product

CONTENTS

4 Breville recommends safety ﬁrst

6 Know your Breville product

8 Assembly & operation of your

Breville product

19 Care, cleaning & storage of your

Breville product

23 Troubleshooting

25 Food preparation guide

29 Recipes

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

• Remove any packaging material and

promotional stickers before using the stick mixer for the ﬁrst time.

• Do not place the stick mixer near

the edge of a bench or table during operation. Ensure the surface is level, clean and free of water, ﬂour, etc.

• Do not place the stick mixer on or near

a hot gas or electric burner, or where it could touch a heated oven.

• If using the stick mixer to blend hot

food in a saucepan over heat, remove the saucepan from the heat source and ensure the power cord and body of appliance are also kept away from any heat source.

• Take care when handling the stick mixer,

attachments and sharp cutting blades, when emptying the bowl and during cleaning. Remember the blade and attachments are very sharp and should be kept out of the reach of children.

• Always make sure the stick mixer is

completely and properly assembled before operating.

• Ensure the stick mixer is turned off at

the trigger switch, the power is switched off at the power outlet and the cord is unplugged from the power outlet before attempting to attach any of the accessories.

• Do not use attachments other than those

provided with the stick mixer.

• Only use the whisk attachment

for the recipes contained in this instruction booklet.

• Do not use the whisk attachment for

anything other than its intended use.

• Do not attempt to operate the stick

mixer by any method other than those described in this booklet.

• Do not process hot or boiling liquids

in food processor bowl – allow liquids to cool before placing into the food processor bowl.

• Do not operate the appliance

continuously for more than 1 minute. Allow the motor to rest for 1 minute between each use.

• Never mix dry, thick or heavy mixtures

for more than 30 seconds. Stop the operation and stir the ingredients before continuing. Allow the motor to rest for 1 minute between each use.

• When using heavy loads, the appliance

should not be operated for more than 30 seconds.

• Always ensure the stick mixer is turned

off, the power is switched off at the power outlet and the cord is unplugged from the power outlet before attempting to move the appliance, when not in use, if left unattended and before disassembling, cleaning or storing.

• If food becomes lodged around the

processing blade or in the blade guard, release the ON button, switch the power off at the power outlet and unplug the cord. Use a spatula to dislodge the food. Do not use ﬁngers as the blades are sharp.

• Do not remove the stick mixer from

ingredients during operation. Ensure the appliance is switched off and has stopped turning before removing, to avoid contact with moving blade or whisk.

BREVILLE RECOMMENDS SAFETY FIRST

• Do not leave the stick mixer unattended

when in use.

• To protect against electric shock do not

immerse the motor body, cord or power plug in water or any other liquid.

• Keep the appliance clean. Follow the

cleaning instructions provided in this book.

• Do not use the stick mixer/stick blender

with wet hands.

• Do not push food into the food chute

with your ﬁngers or other utensils. Always use the food pusher provided.

• Keep ﬁngers, hands, knives and other

utensils away from moving blade and discs.

• Do not place hands or ﬁngers in the

processing bowl of the food processor unless the motor, processing blade, dough blade or disc has come to a complete stop. Ensure the OFF button has been pressed to switch the motor off and the appliance is switched off at the power outlet and the power cord is unplugged before removing the lid from the processing bowl.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

• Unwind the cord fully before use.

• Do not let the cord hang over the edge of

a table or counter, touch hot surfaces or become knotted.

• This appliance is not intended for use by

young children or inﬁrm persons.

• Keep the appliance and its cord out of

reach of children.

• Young children should be supervised to

ensure that they do not play with the appliance.

• It is recommended to regularly inspect

the appliance. Do not use the appliance if power supply cord, plug or appliance becomes damaged in any way. Return the entire appliance to the nearest authorised Breville service centre for examination and/or repair.

• Any maintenance, other than cleaning,

should be performed at an authorised Breville Service Centre.

• This appliance is for household use

only. Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors.

• The installation of a residual current

device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice.

SAVE THESE INSTRUCTIONS

KNOW

your Breville product

TYPESET V1

KNOW YOUR BREVILLE PRODUCT

IJ H

D E

A. Speed Control Dial B. Easy Grip Trigger Switch C. Motor Body D. Processing Gear Box E. Clear Lid F. 1.6L Chopping Bowl G. Feed Chute H. Whisk

I. Stainless Steel Blending Leg J. Variable Masher Leg K. Quad Blade L. Variable Slicing Disc M. Reversible Shredding Disc N. Storage Base O. Spindle

NOT SHOWN

Quad Blade Cover

TYPESET V1

ASSEMBLY & OPERATION

of your Breville product

ASSEMBLY & OPERATION

BEFORE FIRST USE

Remove any packaging material and promotional labels. Remove the blending leg and wash it in warm soapy water (refer to assembly instructions in this booklet). Rinse and dry thoroughly.

Ensure no water remains inside the blending leg to avoid water running into the motor body when reattached. Disassemble and wash the food processor bowl, bowl lid (ensure that the removable gear box has been removed from the lid prior to washing), whisk, quad blade, variable masher leg and variable slicing disc in warm soapy water, rinse and dry thoroughly. Ensure no water remains in the food processor bowl lid or whisk attachment to avoid water running into the motor body when reattached.

NOTE

The detachable blending leg, chopping bowl (without the gearbox), quad blade, variable masher, whisk can also be washed in the dishwasher. The whisk gear box, processor gear box, masher gear box and motor body are not dishwasher safe – see the care and cleaning section of this booklet for cleaning instructions of these parts.

This stick mixer is a versatile appliance that can be attached to:

• The stainless steel blending leg – for use

as a stick mixer.

• The food processor bowl with quad

blade, variable slicing disc, reversible shredding disc - for use as a mini food processor.

• The variable mashing leg – for use as

mashing vegetables.

• The whisk attachment – for use as a

hand whisk.

TO ATTACH THE BLENDING LEG

Hold the blending leg with the blades down, and align the top end of the blending leg with the corresponding end of the motor body and push until the blending leg clicks and locks onto the motor body.

Always ensure blending leg is dry, and no water left inside, before reattaching.

USING AS A STICK MIXER

Ensure the blending leg is assembled to the motor body as detailed above.

1. Place food to be processed into a

sufﬁciently large mixing bowl or saucepan (do not use the food processor bowl as this may damage either the stick mixer or the bowl). The bowl should only be ½ full or less when blending liquids or when making a puree of fruit and/or vegetables.

2. Insert the plug into a 230/240V power

outlet and turn the power on.

3. Turn the dial at the top of motor body,

select a speed from 1 to 15.

NOTE

If selecting a higher speed, it is recommended that you start on a slow speed and then increase to high speed to avoid splattering and over-processing.

ASSEMBLY & OPERATION

4. Place the blending leg as deeply as

possible into the bowl and press the trigger switch to turn the stick mixer on. The button must be held for the required duration of operation.

5. Work through the ingredients in

the bowl with a gentle raising and lowering motion.

6. Switch off the motor by releasing the

trigger switch.

7. Ensure the motor has completely

stopped before lifting the blender out of the bowl.

8. When processing has ﬁnished, switch

off at the power outlet and remove the power plug.

TO DETACH THE BLENDING LEG

Ensure the trigger switch is released, the power is turned off at power point and the appliance is unplugged. Hold the motor body with one hand, and using thumb and ﬁnger of the other hand, press on the two EJECT buttons on either side of the motor body. Pull the motor body away from the blending leg to detach.

RECOMMENDATIONS WHEN USING AS A STICK MIXER

• The stick mixer blends foods and

liquids rapidly, therefore it is easy to over process. Remember when using the blending leg to stop the stick mixer and check food throughout the operation.

• Use caution when blending hot food as it

can splatter.

• The stainless steel blending leg allows

for hot food to be processed directly in the saucepan. This makes blending soups and sauces very easy.

• For safety reasons remove saucepan

away from the heat before processing.

• Ensure the body of the appliance and

power cord are kept away from any heat source.

• When pureeing and blending, cut food

into uniform sizes. This will ensure smooth and consistent results.

• Warm all liquids to be added to soups

and purees, this will ensure even blending.

• Do not operate the appliance

continuously for more than 1 minute. Allow the motor to rest for 1 minute between each use.

If food becomes lodged around the processing blade or in the blade guard, follow the safety instructions below:

1. Release the trigger switch, the power off

at the power outlet and unplug the cord.

2. Use a spatula to carefully dislodge the

food. Do not use ﬁngers as the blades are sharp.

3. After the food has been removed and

blades are clear, plug the appliance back into the power supply, switch the power on and continue blending.

ASSEMBLY & OPERATION

USING THE FOOD PROCESSOR BOWL

ATTACHING GEARBOX TO FOOD PROCESSING BOWL LID

The gearbox should be placed into the food processor lid. It should click into place.

TO ATTACH THE FOOD PROCESSING BOWL, FOOD PROCESSOR ATTACHMENTS AND LID

1. Remove the food processing bowl from

the storage unit and place onto a bench ensuring that the surface is clean and level.

2. Choose one of the following food

processor attachments:

a) Quad blade b) Adjustable slicer c) Reversible shredder

3. There is a common spindle that is

used across all of the three food processor attachments.

WHEN USING THE REVERSIBLE SHREDDER

1. Place the spindle, into the centre of the

food processing bowl.

To attach the motor, click into place onto the gearbox.

CAUTION

Caution should be taken when handling the shredding disc.

ASSEMBLY & OPERATION

2. Holding the reversible shredder disc,

notice that there is a large grater and small grater, place the side you require up. Place over the centre of the spindle and ensure that it is pushed down ﬁrmly.

3. Place the lid into position and ensure

that it is on correctly.

CAUTION

Caution should be taken when handling the adjustable slicing disc and ensure that blade is in the storage or 0 position.

2. The adjustable slicing disc has 24

precise settings. To adjust the settings hold the adjustable slicing disc by the edge (on the opposite side to the cutting blade) with one hand and turn the rotating collar to the desired setting with the other hand.

3. Place the adjustable slicing disc onto

the spindle. Ensure that it is pushed down correctly.

WHEN USING THE ADJUSTABLE SLICER

1. Place the spindle in the centre of the

food processing bowl.

ASSEMBLY & OPERATION

4. Place the lid into position and ensure

that it is on correctly.

WHEN USING THE QUAD BLADE

1. Using care, hold the quad blade in one

hand, with the other hand, place the spindle through the centre of the quad blade from underneath. The quad should self-locate at the base of the spindle. The quad blade will sit loosely on the spindle but will lock into place during processing.

4. Once the blade or disc has been

selected for the food processor you can now process food. Place the food inside the processing bowl. If using the quad blade. Do not exceed the maximum (MAX) marking.

5. Insert the gear box into the lid of the

food processor.

CAUTION

Caution should be taken when handling the quad blade as the blades are extremely sharp.

2. Place the quad blade and spindle into

the centre of the food processing bowl.

3. Place the lid into position and ensure

that it is on correctly.

NOTE

Always place the quad blade into the food processor prior to placing the food into the food processor. When using the disc’s: adjustable slicer and reversible shredder these both can be placed into the food processor prior to processing food. Some foods, such as nuts, can stop the quad blade from engaging the built in safety mechanism. If you have troubles closing the lid with ingredients such as this we advise to load these through the feed chute.

ASSEMBLY & OPERATION

TO USE THE FOOD PROCESSOR

For food preparation tips and recipes refer to the recipe section of this booklet.

1. Insert the plug into a 230/240V power

outlet and turn the power on.

2. Select a speed between 1–15 on the

speed control dial.

3. Press the trigger switch to turn

the appliance on and start the processing action.

4. Feed the food through the feed chute

of the food processor, using the food pusher to push it down.

CAUTION

Only use the small pusher with the large pusher resting inside the feed chute.

5. When processing has ﬁnished switch

off the motor by releasing the trigger switch, switch off at the power outlet and remove the power plug.

6. Detach the food processing bowl and lid

(refer to instructions). Remove the lid from the food processor bowl. Carefully remove the food processing blades or quad blade and use a spatula to scrape off any attached food back into food processing bowl.

+ 30 hidden pages