Bretford 1-Bay, 10-Bay, 5-Bay User Manual

TechGuard® Charging Lockers
User Guide

ver. L15TGUGV1

About Your Prod uct

What's in the Box

1-Bay

TechGuard Charging Locker 1-Bay
Region-specific power cord(s)
2 Administration keycards, programmed for this TechGuard Charging Locker
1 user-applied instruction decal
1 Warranty hang-tag
1 Bretford Warranty Statement
"What's in the Box" page

5-Bay

TechGuard Charging Locker 5-Bay
Region-specific power cord(s)
2 Administration keycards, programmed for this TechGuard Charging Locker
1 user-applied instruction decal
1 Warranty hang-tag
1 Bretford Warranty Statement
"What's in the Box" page

10-Bay

2 TechGuard Charging Locker 5-Bay
1 locker stacking bracket
1 24-inch mounting pedestal with assembly instructions
2 IEC to IEC power cables
1 IEC Y-Plug power adapter
Region-specific power cord(s)
2 Administration keycards, programmed for this TechGuard Charging Locker
1 user-applied instruction decal
1 Warranty hang-tag
1 Bretford Warranty Statement
"What's in the Box" page

Before You Begin

Important Safety Notice

Each TechGuard Charging Locker 10-Bay unit include s a floor mounting kit and wall anchor. The
equipment is to be secured to the building structure before operation.

Additional safety information can be found in the Safety section of this User Guide.

Administration Keycards

Included with the TechGuard Locker are two administration keycards, one (1) access and one (1)
reset. These cards only allow access to the TechGuard Locker in which they are included.
Please pay close attention to the location of these keycards and keep them in a secure location.
For additional information view the Administration Keyca rd section of this User Guide.

Product Registration

Please take a few minutes to register your product with Bretford. With registration, you will be
able to:

Order additional sets of administration cards. (One additional set of administration cards is
available at no cost with product registration.)
Order mounting hardware for 1-bay and 5-bay models.
Receive product updates and support.

Product Overview

About Your New TechGuard Charging Loc ker

Available in 1-Bay, 5-Bay, and 10-Bay models, the Bretford® TechGuard Charging Locker
provides individual lo cking storage and charging for your mobile devices. Each bay of the locker
can accommodate up to two (2) USB devices and one (1) AC device.

1. TechGuard Charging Locker (5-Bay Unit Pictured)

2. Digital Keypad

3. Charging Bay

4. JumpStart access

Mounting T echGuard Lockers

TechGuard Charging Lockers can be mounted or anchored to a floor, wall, counter, or under a
counter.

1-Bay

Surface Mount, Under-Counter Mount

Surface and under-counter mounting hardware
available at no charge by contacting Bretford.

If you have registered your product , you can
make this request online.

5-Bay

Surface Mount, Wall Mount

Surface and wall mounting hardware availabl e
at no charge by contacting Bretford.

If you have registered your product , you can
make this request online.

10-Bay

Floor Mount, Wall Anchor

The 10-Bay TechGuard Locker models
includes a floor mounting and wall anchor kit.

WARNING:The equipmen t is to be secured to
the building structure before operation.

Technical Specifications

Size and Weight

Model 1-Bay 5-Bay 10-Bay

Dimensions

19 x 19 x 4.75 in

48.3 x 48.3 x 12.x cm

19 x 19 x 21 in

48.3 x 48.3 x 53.4 cm

19 x 19 x 67 in

48.3 x 48.3 x 53.4 cm

Weight

25 lbs

11.3 kg

86 lbs

39.0 kg

217 lbs

98.4 kg

Charging

Each bay of the TechGuard Locker offers:

One (1) AC outlet, supports up to a 100 W power adapter.
Two (2) USB charging ports, up to 2.4 A each.

Electrical and Operating Requirements

The TechGuard Locker has been engineered to charge all connected devices from a single
15 A AC circuit.
Maintenance-free keypad locks are powered by the internal system power supply. No
batteries required.

Administration Keycards

Access Keycard

The Access Card will open a bay but keep the current unlock code, allowin g facilities personnel
to inspect contents of an in-use locker.

Reset Keycard

The Reset Card will open a bay and reset the current unlock code, in the event of a forgotten
code.

Using An Administration Keycard

1. Hold the appropriate card up to the keypad next to the locker bay you wish to access or
reset.

2. The keypad will unlock and respond w ith an audible confirmation.

Important Keycard Information

Each TechGuard locker includes two administration keycards, one (1) access and one (1)
reset.

Each pair of cards will only allow access to the TechGuard Locker in which they are
included. They cannot be shared with multiple 1-Bay, 5-Bay or 10-Bay units.

Always keep your keycards in a secure location.

TechGuard Accessories

The following accessories are avail able from Bretford for TechGuard Charging Lockers:

Lightning cable with retaining cli p (1-pack / 5-pack)
Micro-USB cable with retaining clip (1-pack / 5-pack)
Jump Starter Kit, used to power Keypad and door lock during power outages

JumpStarter Accessory Kit

The optional JumpStarter Accessory Kit provides temporary power to a TechGuard Charging
Locker during a power outage, allowing users and administrators to open locker bays with the
user’s passcode, or the administrator keycards.

The JumpStarter Accessory Kit includes:

JumpStarter port opener tool
Battery pack
JumpStarter connection cable

To use the JumpStarter Accessory Kit to open a locker:

1. Use the JumpStarter port opener tool to pry open the JumpStarter port cover. Slide the
keyed end of the tool into the notch on the bottom edge of the port cover until it clicks, and
gently pry open the cover.

2. Plug the JumpStarter connection cable into the battery pack and connect to the JumpStarter
Accessory Port.

3. The battery will begin providing powe r to the keypads so they can be opened normally,
using the user’s passcode or an administrator keycard.

The JumpStarter Accessory Kit does not provide charging power to connected devices in each
bay.

More information about the JumpStarter Accessory Kit is available at bretford.com/techguard.

Getting Started

Installing You r TechGuard Locker

Where To Install

Before installing your TechGuard Charging Locker pleas e read the Safety section of this User
Guide.

Powering Your T echGuard Locker

Step-By-Step

1. Locate and unwrap the region specific AC power cord provided with your TechGuard
Locker.

2. Connect the power cord to the rear side of the TechGuard Locker.

3. Connect the power cord to a dedicated 15 A circuit.