Bresser 7002570 Instruction Manual

Weather Station ·

PC Weather Station with multifunction sensor

EN Instruction manual

3

Contents

1 Imprint .............................................................................................................................................................4

2 Validity information ........................................................................................................................................4

3 About this Instruction Manual.......................................................................................................................4

4 Parts overview Multisensor ...........................................................................................................................5

5 Parts overview Base station and Scope of delivery....................................................................................6

6 Screen display ................................................................................................................................................ 8

7 Before starting operation...............................................................................................................................9

8 Setting up power supply................................................................................................................................9

9 Attaching rubber pads ................................................................................................................................. 10

10 Assembling and installing the multifunctional remote sensor ................................................................11

11 Signal transmission .....................................................................................................................................12

12 Time synchronization with the PC ..............................................................................................................12

13 Manual time setting ......................................................................................................................................12

14 Setting up the station for weather data transmission............................................................................... 13

15 EC Declaration of Conformity .....................................................................................................................13

16 Disposal......................................................................................................................................................... 13

17 Warranty ........................................................................................................................................................13

4 / 16

1 Imprint

Bresser GmbH

Gutenbergstr. 2
46414 Rhede
Germany

http://www.bresser.de

If you wish to submit a warranty claim or service request, please refer to the “Warranty” and “Service”
information in this document. Please be aware that any requests or submissions sent directly to the
manufacturer cannot be processed.

Errors excepted. Subject to technical modifications.

© 2019 Bresser GmbH

All rights reserved.

Reproduction of this document, including extracts, in any form (photocopied, printed etc.) or the use
and distribution of this document by electronic means (image file, website etc.) is not permitted without
the prior written consent of the manufacturer.

The terms and brand names of the respective companies used in this document are protected by
brand, patent or product law in Germany, the European Union and/or other countries.

2 Validity information

This documentation is valid for the products with the article numbers listed below:

7002570

Manual version: v0219

Manual description:

Manual_7002570_PC-Weather-Station_en_BRESSER_v022019a

With any service inquiries, please state these information.

3 About this Instruction Manual

NOTICE

These operating instructions are to be considered a component of the device.

Please read the safety instructions and the operating instructions carefully before use.

Keep these instructions for renewed use at a later date. When the device is sold or given to someone
else, the instruction manual must be provided to the new owner/user of the product.

5 / 16

4 Parts overview Multisensor

1

2

3

6

7

5

8

9

10

B

4

11

12

13

1 Wind vane 2 Wind cups (Anemometer)
3 Antenna 4 Radiation shield
5 Mounting hole for vertical mounting pole (pipe

diameter: 35-40 mm)

6 Hygro-Thermal sensor

7 Battery compartment door 8 RESET button
9 Function indicator 10 Circular level

11 Rain collector (sinkhole) 12 UV Sensor

6 / 16

13 Solar panel

5 Parts overview Base station and Scope of

delivery

1

2

3

4

5

6

7

8

9

10

11

13

14

15

16

17

18

19

20

21

22

23

24

12

25

A

C

Illustration1: All parts of the base station

1 Display 2 Housing
3 SNOOZE/LIGHT button (snooze function

and temporary background lighting)

4 CHANNEL button (channel selection)

5 GRAPH/UP button (normal diplay: bar

chart for history data/settings: value
change upwards)

6 HISTORY/DOWN button (normal display:

single values of history data/settings:
value change downwards)

7 MAX/MIN button (switch between highest,

lowest or current value display)

8 BARO button (display of different atmo-

spheric pressure values)

9 WIND button (display change between av-

erage and current gust)

10 RAIN button (display change between

daily, weekly and monthly rainfall)

11 INDEX button (change between dew

point, heat index and wind chill index dis­play)

12 microUSB slot (connecting with a PC* us-

ing the included USB cable)

13 Wall mount fixture 14 ALARM button (alarm time setting or dis-

play change)

15 ALERT button (temperature setting or dis-

play change)

16 RESET button (reset all settings)

17 TIME SYNC button (initiate time syn-

chroinization* via PC)

18 Battery compartment

19 Battery compartment cover 20 Stand, fold-out
21 DATA button (initiate data transfer* to the

PC)

22 °C/°F button (temperature format setting)

7 / 16

23 SENSOR button (initialize remote sensor

data reception)

24 CLOCK SET button (manual time setting)

25 USB cable with microUSB plug (base sta-

tion) and USB-A plug (PC)

*Weather data transmission requires a PC with Windows 7 or higher and installed 'WEATHER TOOL'
software.

Scope of delivery

Base station (A), outdoor sensor (multifunctional remote sensor) (B), USB cable (C)

Also required (not included):

6 pcs. Mignon batteries (1.5V, AA type) for base station; 3 pcs. Mignon batteries (1.5V, AA type) for
multifunctional remote sensor

8 / 16

6 Screen display

1

4

3

28

2

6

7

9

11

10

13

12

14

15

17

16

19

20

22

21

24

18

23

26

25

27

5

8

Illustration2: Screen display of the base station

1 Current time or alarm time

(hours:minutes:seconds)

2 Alarm enabled

3 Sync icon (time) 4 Date (day-month or reverse)
5 Weekday 6 Moon phase
7 Bar chart for value display 8 Air pressure alarm enabled

9 Air pressure 10 Sunrise time
11 Sunset time 12 Wind speed alarm enabled
13 Wind speed 14 Alarm for high (HI AL) or low (LO AL) value

enabled

15 Outdoor temperature 16 Alarm for high (HI AL) or low (LO AL) value

enabled

17 Indoor temperature 18 Humidity outdoors

9 / 16

19 Humidity indoors 20 Room climate Indicator
21 Sensor signal status 22 Sensor symbol
23 Wind/storm classification 24 Wind direction
25 Index (heat/dew point/UV/Beaufort) 26 Index value
27 Weather trend 28 AM/PM information in 12-hour time mode

7 Before starting operation

NOTICE

Avoid connectivity disruptions!

To avoid connectivity disruptions between the devices, consider the following points before starting
operation.

1. Place base station (receiver) and remote sensor (sender) together as close as possible.

2. Set up power supply for the base station and wait until the indoor temperature is displayed.

3. Set up power supply for the remote sensor.

4. Position the base station and the remote sensor within the effective transmission range.

5. Ensure that the base station and remote sensor are assigned to the same channel.

When changing batteries always change batteries in the main unit as well as all remote units and re­place them in the correct order, so the remote connection can be re-established. If either of the
devices is mains-powered, the power supply must be disconnected for a short moment also for this
device when exchanging the batteries. If batteries are exchanged in only one of the devices (i.e. the
remote sensor) the signal can’t be received or can’t be received correctly.

Note, that the effective range is vastly affected by building materials and position of the main and re­mote units. Due to external influences (various RC devices and other sources of interference), the
maximum distance can be greatly reduced. In such cases we suggest to position the main unit and the
remote sensor at other places. Sometimes all it takes is a relocation of one of these components of a
few inches! Though the remote unit is weather proof, it should be placed away from direct sunlight,
rain or snow.

8 Setting up power supply

Base unit

1. Remove the battery compartment cover.

2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

3. Replace the battery compartment cover.

Remote sensor

4. Loosen the screw at the battery compartment cover with a small Philips screwdriver and remove
the cover.

5. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

6. Replace the cover and retighten it with the screw.

10 / 16

9 Attaching rubber pads

Attach the supplied self-adhesive rubber pads to the clamps as shown to ensure a firmer fitting of the
mounting rod.

11 / 16

10 Assembling and installing the multifunctional

remote sensor

NORTH

1.5 m

1

2

3

4

7

1

2

8

6

5

5

1 U-bolt (2x) 2 Mounting clamp (4x)
3 Washer (4x) 4 Nuts (4x)
5 Mounting pole (1x) Pole placed under egg

tray. Please check before disposal of the
packaging.

6 Battery compartment

7 Screws (4x) 8 Point to the North and at least 1.5 metres off

the ground.

Depending on the desired location, the remote sensor can be installed in different ways.

12 / 16

NOTICE!During the assembly make sure that the upper part of the wind vane is minimum 1.5
metres off the ground. Use the circular level in the sensor head to ensure a level installation. The
windmill must point to the North.

Assembly on a vertical or horizontal tube

1. Insert the stainless steel mounting pole into the mounting hole of the sensor and tighten the
screws firmly.

2. Attach the stainless steel pole to a post or pipe using the 2 U-bolts, mounting clamps and nuts.

11 Signal transmission

The base station will automatically connect to the multi outdoor sensor and (if available) to other wire­less sensors. Press the SENSOR SYNC button to search for sensors directly. After successful con­nection, the symbol for the outdoor area (OUT) and/or the channel are displayed.

Connection status display

Connection status Screen display

Good signal Reception icon
Searching for a sensor Reception symbol flashes
No signal for 48 hours 'Er' (Error) is shown
Sensor low battery status, good signal Battery symbol is shown

12 Time synchronization with the PC

Time and date are automatically synchronized for this device when it is connected to a computer* via
the supplied USB cable. Proceed as follows:

1. Put the microUSB plug of the USB cable into the USB slot of the device.

2. Put the USB-A plug of the cable into a free USB port of the computer.

3. Turn on the computer and wait approx 5 seconds.

4. Press the TIME SYNC button for approx. 8 seconds to disable or enable time synchronization.

5. Press TIME SYNC button once to initiate time synchronization again.

NOTICE!The time synchronization ensures through the time on the connected computer. Make
sure it is set correctly. Once the time has been synchronized, this will be indicated by the sync
symbol on the display.

6. *Computer with Windows 7 or higher required.

NOTICE!Once the device is connected to the computer via USB, it will be powered by the com­puter as soon as the computer is turned on.

13 Manual time setting

To set the time / date manually, first disable the reception of the time signal by pressing the RCC but­ton for approx. 8 seconds.

1. Press and hold CLOCK button for approx. 3 seconds to change to time setting mode.

2. Digits to be set are flashing.

3. Press UP or DOWN button to change the value.

4. Press CLOCK button to confirm and continue to the next setting.

5. Settings order: 12/24-hours mode > Hours > Minutes > Year > Month > Day > Time offset > Lan­guage > Daylight Saving Time (DST)

6. Finally press the CLOCK button to save the settings and exit the setting mode.

13 / 16

14 Setting up the station for weather data

transmission

NOTICE!For the weather data transmission to the Weather Underground community an internet
connection is required. Fo the data receivement using the free Weather Tool software, a com­puter with a free USB port and Windows operating system is required.

To transfer weather data from the weather station to a computer or to the Weather Underground com­munity, the following preparatory steps are required:

1. Download the software 'Weather Tool' as a zip file from http://archive.bresser.de/down-

load/7002570/software

2. Unpack the zip file on the computer.

3. In the selected target directory a corresponding folder 'WEATHER_TOOL_7_26' is created.

4. The folder contains the installation file 'WEATHER TOOL-7-26.exe' as well as a manual for setting
up the weather station for weather data transmission.

5. Open the installation file with a double click of the left mouse button and follow the instructions of
the installation wizard.

6. Connect the weather station with the computer.

7. Read the manual for the software in detail and set up the weather station according to the specific­ations. (For more information, see the chapter 'Time synchronization with the PC')

15 EC Declaration of Conformity

Hereby, Bresser GmbH declares that the equipment type with item number 7002570 : is in compli­ance with Directive: 2014/30/EU. The full text of the EU declaration of conformity is available at the
following internet address: www.bresser.de/download/7002570/CE/7002570_CE.pdf

16 Disposal

Dispose of the packaging materials properly, according to their type, such as paper or card­board. Contact your local waste-disposal service or environmental authority for information
on the proper disposal.

Do not dispose of electronic devices in the household garbage!

As per Directive 2012/19/EC of the European Parliament on waste electrical and electronic
equipment and its adaptation into German law, used electronic devices must be collected
separately and recycled in an environmentally friendly manner.

Do not dispose of batteries and rechargeable batteries with the household waste. You are leg­ally required to return used batteries and rechargeable batteries. After they are used, the bat­teries can be returned free of charge to our point of sale or to a nearby location (for example,
retailers or municipal collecting points).

Batteries and rechargeable batteries are marked with a symbol of a crossed-out dustbin and
the chemical symbol of the pollutant. “Cd” stands for Cadmium, “Hg” stands for mercury and
“Pb” stands for lead.

17 Warranty

The regular guarantee period is 2 years and begins on the day of purchase. To benefit from an exten­ded voluntary guarantee period as stated on the gift box, registration on our website is required.

14 / 16

You can consult the full guarantee terms as well as information on extending the guarantee period and
details of our services at www.bresser.de/warranty_terms.

DE AT

CH BE

Bei Fragen zum Produkt und eventuellen
Reklamationen nehmen Sie bitte zunächst mit
dem Service-Center Kontakt auf, vorzugsweise
per E-Mail.

E-Mail: [e-mail]
Telefon*: [phone]

BRESSER GmbH
Kundenservice
Gutenbergstr. 2
46414 Rhede
Deutschland

* Lokale Rufnummer in Deutschland (Die Höhe der Gebühren je

Telefonat ist abhängig vom Tarif Ihres Telefonanbieters); Anrufe
aus dem Ausland sind mit höheren Kosten verbunden.

GB IE

Please contact the service centre first for any
questions regarding the product or claims,
preferably by e-mail.

e-mail: [e-mail]

Telephone*: [phone]
BRESSER UK Ltd

Unit 1 starborough Farm,
Starborough Road, Nr Marsh Green,
Edenbridge, Kent TN8 5RB
Great Britain

* Number charged at local rates in the UK (the amount you will be

charged per phone call will depend on the tariff of your phone
provider); calls from abroad will involve higher costs.

FR BE

Si vous avez des questions concernant ce
produit ou en cas de réclamations, veuillez
prendre contact avec notre centre de services
(de préférence via e-mail).

e-mail: [e-mail]

Téléphone*: [phone]
BRESSER France SARL

Pôle d'Activités de Nicopolis
260, rue des Romarins
83170 Brignoles
France

* Prix d'un appel local depuis la France ou Belgique

Service

NL BE

Als u met betrekking tot het product vragen
of eventuele klachten heeft kunt u contact
opnemen met het service centrum (bij voorkeur
per e-mail).

e-mail: [e-mail]

Teléfono*: [phone]
Folux B.V.

Smirnoffstraat 8
7903 AX Hoogeveen
Nederlands

* Het telefoonnummer wordt in het Nederland tegen lokaal tarief

in rekening gebracht. Het bedrag dat u per gesprek in rekening
gebracht zal worden, is afhankelijk van het tarief van uw telefoon
provider; gesprekken vanuit het buitenland zullen hogere kosten
met zich meebrengen.

ES CA PT

Si desea formular alguna pregunta sobre el
producto o alguna eventual reclamación, le
rogamos que se ponga en contacto con el
centro de servicio técnico (de preferencia por
e-mail).

e-mail: [e-mail]

Teléfono*: [phone]
BRESSER Iberia SLU

c/Valdemorillo,1 Nave B
P.I. Ventorro del cano
28925 Alcorcón Madrid
España

* Número local de España (el importe de cada llamada telefónica

dependen de las tarifas de los distribuidores); Las llamadas des del
extranjero están ligadas a costes suplementarios.