BY ....................................................................................................................................30
MULTISTYLER BR3204BN
Multistyler is intended for nger wave styling of
hair. Unusual waves are created by putting a lock
of hair on the heating plate of the multistyler and
pressing it with two cylindric elements.
DESCRIPTION
1. Operating elements
2. Operating element temperature setting buttons
«-/+»
3. On/o button«
4. Temperature scale
5. Hanging loop
6. Wave intensity knob
ATTENTION!
– Do not use the unit near water in the bathrooms,
showers, swimming pools etc.
– After using the unit in a bathroom, unplug it and
take the power plug out of the mains socket, as the
proximity of water is dangerous even if the unit is
switched o.
»
– For additional protection it is reasonable to install a
residual current device (RCD) with nominal operation
current not exceeding 30 mA into the mains of a
bathroom. To install it, contact an electrical echnician.
6
2
1
3
4
5
45ENEN
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
Read the operation instructions carefully before using the unit, after reading keep them for future reference.
• Use the unit for its intended purpose only, as
specied in this manual.
• Mishandling the unit can lead to its breakage and
cause harm to the user or damage to his/her property
and it is not covered by warranty.
• The multistyler is intended only for styling of slightly
wet and dry hair, do not use the unit for styling of wet
hair or synthetic wigs.
• Make sure that operating voltage of the unit indicated
on the label corresponds to your home mains
voltage.
• Do not use the unit when you are drowsy.
• Do not use the unit outdoors.
• It is recommended not to use the unit during lightning
storms.
• Protect the unit from blows, drops, vibrations and
other mechanical stress.
• Never leave the plugged-in multistyler unattended.
• Do not use the unit near heating appliances, heat
sources or open ame.
• Do not use the unit in places where aerosols are
used or sprayed, and in proximity to inammable
liquids.
• Do not use the unit in proximity to kitchen sink, in
bathrooms, near swimming pools or other containers
lled with water.
• Do not use the unit while taking a bath.
• Do not hang and do not keep the unit in places where
it can fall into a bath or a sink lled with water; do not
immerse the unit body, power cord or power plug into
water or any other liquid.
• If the unit is dropped into water, unplug it
immediately, and only then you can take the unit out
of water.
• Do not let the power cord touch hot surfaces and
sharp edges of furniture.
• Unplug the unit after usage or before cleaning. When
unplugging the unit hold the power plug and carefully
remove it from the mains socket, do not pull the
power cord — this can lead to its damage and cause
short circuit.
• Do not touch the unit body, the power cord and the
power plug with wet hands.
• During the operation, hold the unit at handle area
only, do not touch the operating surface.
• Avoid contact of hot surfaces with your face, neck
and other parts of your body.
The operating surface remains hot for some time
after the unit is unplugged. Be careful!
• For child safety reasons do not leave polyethylene
bags used as packaging unattended.
ATTENTION!
Do not allow children to play with polyethylene bags
or packaging lm. Danger of suocation!
• The multistyler is not intended for usage by children.
• Do not leave children unattended to prevent using
the unit as a toy.
• Do not allow children to touch the operating surface,
unit body, power cord or power plug during operation
of the unit.
• Be especially careful if children or disabled persons
are near the operating unit.
• During the unit's operation and breaks between
operation cycles, place the unit out of reach of
children.
• The unit is not intended for usage by physically or
mentally disabled persons (including children) or by
persons lacking experience or knowledge if they are
not under supervision of a person who is responsible
for their safety or if they are not instructed by this
person on the usage of the unit.
• Regularly check the integrity of the power cord.
• If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or
similar qualied personnel to avoid danger.
• Do not repair the unit by yourself. Do not
disassemble the unit by yourself, if any malfunction
is detected, and after the unit was dropped, unplug it
and apply to the service center.
• To avoid damages, transport the unit in original
package only.
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE
ONLY
BEFORE THE FIRST USE
After unit transportation or storage at negative
temperature, unpack it and wait for 3 hours before
using.
• Unpack the unit and remove all the packaging
materials.
• Keep the original package.
• Check the delivery set.
• Read the safety measures and operating
recommendations.
• Examine the unit for damages, in case of damage do
not plug it into the mains.
• Make sure that specied specications of power
supply voltage of the unit correspond to the
specications of your mains. When using the unit in
the mains with 60 Hz frequency, the unit does not
need any additional settings.
• Wipe the unit with a clean, slightly damp cloth to
remove dust, and then wipe it dry.
• Unwind the power cord to its full length while using
the unit.
67ENEN
USING THE MULTISTYLER
Use the multistyler for both long hair and hair of
middle length.
• Place the multistyler on a at steady heat-resistant
surface. Make sure that the operating elements
and the outer surfaces do not touch fusible and
inammable objects.
• Use the unit on healthy undyed and not permed hair.
• If your hair is dyed or was permed, use the multistyler
rarely.
• Before styling wash your hair with shampoo, wipe it
with a towel, dry with a hairdryer and comb your hair.
• Put the multistyler on a at steady and heat-resistant
surface.
• Insert the power plug into the mains socket.
• Switch the unit on by pressing and holding the on/
o button (3) «
temperature indicators from «120» to «200» and the
default heating temperature «180» will light up and
start ashing on the temperature scale (4).
• Note: — when switching the unit on for the rst time,
a smell from the heating element can appear, this is
normal and it is not covered by warranty.
• If necessary, set the required operating elements
temperature by pressing the buttons «-/+» (2).
». The operating element (1)
Hair type Temperature
Damaged, colored, bleached,
ne
Normal from +140 °С to +180 °С
For professional stylingfrom +180 °С to +200 °С
Temperature from +120 °С to
+140 °С
• When the operating elements (1) reach the set
temperature, the temperature light indicators on the
scale (4) will be glowing constantly.
Some useful tips
- Use the multistyler only on dry hair. If your hair
is wet, the liquid abruptly starts boiling when hair
comes in contact with hot surfaces. It may damage
your hair.
- It is recommended to use hair styling products with
thermal protection.
- Use nourishing, moisturizing or repairing hair
masks several times a week.
- After washing your hair rinse it with a herbal tea.
Use chamomile infusion for fair hair and sage, oak
bark or hop infusions for dark hair. The nettle tea
is an universal product for all hair types.
S-SHAPED HAIR LOCKS
• Turn the knob (6) to set the hair wave intensity.
• Divide hair into locks about 5-7 cm wide.
• Switch the multistyler on, set the required heating
temperature with the buttons (2) «-/+», wait until the
operating elements (1) heat up.
• Unusual waves are created by putting a lock of
hair on the heating plate of the multistyler (1) and
pressing it with two cylindric elements.
• Separate a lock of hair, press it between the
operating elements (1) of the multistyler starting from
the roots. Be careful, avoid contact of the heated
element (1) with your scalp but at the same time
do not place the multistyler far from the hair roots
otherwise you don’t get the root volume.
• First make an inner curl on each hair lock and then
an outer.
• Do not stay longer than for 5 seconds at each part of
the hair lock.
• After you nish using the multistyler, switch it o by
pressing and holding the on/o button (3) «
» and
unplug the unit.
• Notes:
- always switch the unit o and unplug it when
you’re not using it.
- never leave the hair straightener connected to the
mains unattended; if you forgot to switch it o, the
hair straightener will be switched o automatically
in 60 minutes.
• Divide big locks into smaller ones with your hands.
• After styling x your hair with the hair spray.
• Notes:
- after using the multistyler several time you will be
able to masterfully create fancy waves on your
hair. You can use this manner of styling not only as
a regular hairstyle but also as an addition to other
hairstyles.
- you can nd more detailed instructions for making
nger waves freely available on the Internet.
CLEANING AND MAINTENANCE
• Before cleaning switch the multistyler o, unplug it
and let it cool down completely.
• Do not immerse the unit, the power cord and the
power plug into water or other liquids.
• Do not use abrasives and solvents to clean the unit
body and the operating elements (1).
• Wipe the multistyler with a soft, slightly damp cloth
and then wipe it dry.
STORAGE
• Let the unit cool down completely and clean it before
taking away for storage.
• Never wind the power cord around the unit body, as it
can damage the cord or the unit body.
• For easy storage, there is a hanging loop (5) you can
store the unit on, provided that in such position no
water will get on the unit.
DE
9DE8EN
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
DELIVERY SET
1. Multistyler — 1 pc.
2. Instruction manual — 1 pc.
TECHNICAL SPECIFICATIONS
• Supply voltage: 100-240 V, ~ 50/60 Hz
• Rated input power: 80 W
ATTENTION!
Do not use the unit near water in the
bathrooms, showers, swimming pools
etc.
RECYCLING
To prevent possible damage to the
environment or harm to the health of
people by uncontrolled waste disposal,
after service life expiration of the unit or the
batteries (if included), do not discard them
with usual household waste, deliver the unit and the
batteries to specialized centers for further recycling.
The waste generated during the disposal of the unit
is subject to mandatory collection and consequent
disposal in the prescribed manner.
For further information about recycling of this product
apply to a local municipal administration, a disposal
service or to the shop where you purchased this
product.
The manufacturer reserves the right to change the
design, structure and specications not aecting
general principles of the unit operation, without prior
notice.
The unit operating life is 3 years
MULTISTYLER BR3204BN
Der Multistyler ist ein Gerät fürs Haarstyling im
Retrowellen-Stil. Ungewöhnliche Wellen werden
erschaen, wenn eine Haarsträhne auf die
Arbeitsäche des Multistylers gelegt und durch
zwei zylindrische Elemente gedrückt wird.
BESCHREIBUNG
1. Arbeitselemente
2. Einstelltasten der Arbeitselemententemperatur
«-/+»
3. Ein-/Ausschalttaste « »
4. Temperaturskala
5. Aufhängeöse
6. Wellenintensitätsregler
ACHTUNG!
– Das Gerät in der Nähe des Wassers in
Badezimmern, Duschräumen, Wasserbecken usw.
nicht benutzen.
– Nach der Nutzung des Geräts im Badezimmer
schalten Sie es aus und ziehen Sie den Netzstecker
aus der Steckdose heraus, weil die Nähe des
Wassers gefährlich ist, wenn das Gerät sogar mittels
Netzschalter ausgeschaltet ist.
– Als zusätzlicher Schutz ist es zweckmäßig,
den FI-Schalter mit Nennstrom bis 30 mA im
Stromversorgungskreis des Badezimmers
aufzustellen; wenden Sie sich dafür an einen
Elektriker.
6
2
1
3
4
5
1011DEDE
SICHERHEITSHINWEISE UND
BEDIENUNGSANLEITUNG
Bevor Sie das Gerät benutzen, lesen Sie zuerst
die Bedienungsanleitung aufmerksam durch und
bewahren Sie sie zum späteren Gebrauch auf.
• Benutzen Sie das Gerät bestimmungsmäßig und laut
dieser Bedienungsanleitung.
• Missbrauch des Geräts kann zu seiner Störung
führen, den Benutzer oder sein Eigentum
beschädigen und ist kein Garantiefall.
• Der Multi-Styler ist nur fürs Styling von trockenem
und leicht feuchtem Haar bestimmt; benutzen
Sie das Gerät fürs Styling von nassem Haar oder
synthetischen Perücken nicht.
• Vergewissern Sie sich, dass die auf dem
Bezeichnungszettel angegebene Betriebsspannung
und die Netzspannung übereinstimmen.
• Benutzen Sie das Gerät nicht, wenn Sie schläfrig
sind.
• Es ist nicht gestattet, das Gerät draußen zu
benutzen.
• Es ist nicht empfohlen, das Gerät bei Gewitter zu
benutzen.
• Schützen Sie das Gerät vor Stößen, Stürzen,
Vibrationen und anderen mechanischen
Einwirkungen.
• Lassen Sie den ans Stromnetz angeschlossenen
Multi-Styler nie unbeaufsichtigt.
• Benutzen Sie das Gerät in direkter Nähe von
Heizgeräten, Wärmequellen oder oenem Feuer
nicht.
• Es ist verboten, das Gerät an den Orten, wo
Sprays verwendet werden, sowie in der Nähe von
leichtentzündbaren Flüssigkeiten, zu benutzen.
• Benutzen Sie das Gerät in der Nähe von Spülbecken,
in Badezimmern und neben den Wasserbecken oder
anderen mit Wasser gefüllten Behältern nicht.
• Es ist nicht gestattet, das Gerät beim Baden zu
benutzen.
• Es ist nicht gestattet, das Gerät an den Stellen
anzuhängen und aufzubewahren, wo es in die mit
Wasser gefüllte Wanne oder ins Waschbecken
stürzen kann; tauchen Sie das Gerätegehäuse, das
Netzkabel oder den Netzstecker ins Wasser oder
jegliche andere Flüssigkeit nicht ein.
• Falls das Gerät ins Wasser gefallen ist, ziehen Sie
den Netzstecker aus der Steckdose sofort heraus,
erst danach holen Sie das Gerät aus dem Wasser
heraus.
• Achten Sie darauf, dass das Netzkabel heiße
Oberächen und scharfe Möbelkanten nicht berührt.
• Trennen Sie das Gerät nach dem Gebrauch oder
vor der Reinigung vom Stromnetz ab. Wenn Sie
das Gerät vom Stromnetz abtrennen, halten Sie
den Netzstecker fest und ziehen Sie ihn aus der
Steckdose vorsichtig heraus; ziehen Sie das
Netzkabel nicht, da es zu seiner Beschädigung und
einem Kurzschluss führen kann.
• Berühren Sie das Gerätegehäuse, das Netzkabel
und den Netzstecker mit nassen Händen nicht.
• Während des Betriebs halten Sie das Gerät nur am
Gri und berühren Sie die Arbeitsäche nicht.
• Vermeiden Sie die Berührung von heißen
Oberächen des Geräts mit Gesicht, Hals und
anderen Körperteilen.
•
Die Arbeitsäche bleibt einige Zeit nach dem
Geräteabtrennen vom Stromnetz heiß. Seien Sie
vorsichtig!
• Aus Kindersicherheitsgründen lassen Sie
Plastiktüten, die als Verpackung verwendet werden,
nie ohne Aufsicht.
ACHTUNG!
Lassen Sie Kinder mit Plastiktüten oder
Verpackungsfolien nicht spielen. Erstickungsgefahr!
• Der Multi-Styler ist nicht für Kinder bestimmt.
• Beaufsichtigen Sie Kinder, damit sie das Gerät als
Spielzeug nicht benutzen.
• Lassen Sie Kinder die Arbeitsäche, das
Gerätegehäuse, das Netzkabel oder den Netzstecker
während des Gerätebetriebs nicht berühren.
• Besondere Vorsichtsmaßnahmen sind in den
Fällen angesagt, wenn sich Kinder oder behinderte
Personen während des Gerätebetriebs in der Nähe
aufhalten.
• Während des Betriebs und der Pausen zwischen den
Betriebszyklen stellen Sie das Gerät an einem für
Kinder unzugänglichen Ort auf.
• Dieses Gerät ist für Personen (darunter Kinder)
mit Körper-, Nerven- und Geistesstörungen
oder Personen ohne ausreichende Erfahrung
und Kenntnisse nicht geeignet, wenn sie sich
unter Aufsicht der Person, die für ihre Sicherheit
verantwortlich ist, nicht benden oder entsprechende
Anweisungen über die Nutzung des Geräts nicht
bekommen haben.
• Prüfen Sie die Unversehrtheit des Netzkabels von
Zeit zu Zeit.
• Wenn das Netzkabel beschädigt ist, soll es
vom Hersteller, Kundendienst oder von ähnlich
qualiziertem Personal ersetzt werden, um Gefahren
zu vermeiden.
• Es ist nicht gestattet, das Gerät selbständig
zu reparieren. Es ist nicht gestattet, das Gerät
selbständig auseinanderzunehmen; bei der
Feststellung jeglicher Beschädigungen, sowie im
Sturzfall, trennen Sie das Gerät vom Stromnetz ab
und wenden Sie sich an einen Kundendienst.
1213DEDE
• Um Beschädigungen zu vermeiden, transportieren
Sie das Gerät nur in der Fabrikverpackung.
• Bewahren Sie das Gerät an einem trockenen,
kühlen und für Kinder und behinderte Personen
unzugänglichen Ort auf.
DAS GERÄT IST NUR FÜR DEN GEBRAUCH IM
HAUSHALT GEEIGNET
VOR DER ERSTEN NUTZUNG
Packen Sie das Gerät aus und warten Sie 3 Stunden,
bevor Sie es bei einer negativen Temperatur
transportieren oder bewahren.
• Packen Sie das Gerät aus und entfernen Sie alle
Verpackungsmaterialien.
• Bewahren Sie die Originalverpackung auf.
• Prüfen Sie die Komplettheit.
• Lesen Sie die Sicherheitsmaßnahmen und
Bedienungsempfehlungen durch.
• Prüfen Sie das Gerät auf Beschädigungen; wenn
es beschädigt ist, schließen Sie es ans Stromnetz
nicht an.
• Vergewissern Sie sich, dass die angegebenen
Parameter der Geräteversorgungsspannung und die
Stromnetzparameter übereinstimmen. Beim 60-Hz-
Stromnetz-Gerätebetrieb sind keine zusätzlichen
Maßnahmen erforderlich.
• Wischen Sie das Gerät mit einem sauberen, leicht
angefeuchteten Tuch zur Staubentfernung, danach
trocknen Sie es ab.
• Es ist empfohlen, das Netzkabel während der
Gerätenutzung vollständig abzuwickeln.
MULTISTYLER-BETRIEB
Benutzen Sie den Multistyler sowohl für langes als
auch für mittellanges Haar.
• Stellen Sie den Multistyler auf eine ebene,
standfeste und hitzebeständige Oberäche auf.
Achten Sie darauf, dass die Arbeitselemente und die
Außenoberächen mit keinen leichtschmelzbaren
oder verbrennlichen Gegenständen in Kontakt
kommen.
• Benutzen Sie das Gerät zum Stylen von gesundem,
ungefärbtem und nicht dauergewelltem Haar.
• Wenn das Haar gefärbt oder dauergewellt ist,
benutzen Sie den Multistyler nur selten.
• Vor dem Styling waschen Sie das Haar mit Shampoo,
wischen Sie es mit einem Handtuch ab, trocknen Sie
es mit einem Haartrockner und kämmen Sie es.
• Legen Sie den Multistyler auf eine ebene, standfeste
und hitzebeständige Oberäche.
• Stecken Sie den Netzstecker in die Steckdose ein.
• Schalten Sie das Gerät ein, drücken und halten
Sie dafür die Ein-/Ausschalttaste (3) «
werden die Anzeigen der Erwärmungstemperatur
», dabei
der Arbeitselementen (1) von «120» bis «200»
an der Temperaturskala (4) leuchten und blinken,
die voreingestellte Erwärmungstemperatur der
Arbeitselementen ist «180».
• Anmerkung: — bei erster Gerätenutzung kann ein
Fremdgeruch vom Heizelement entstehen, es ist
normal und kein Garantiefall.
• Falls notwendig, stellen Sie die gewünschte
Erwärmungstemperatur der Arbeitsplatten mit den
Tasten «-/+» (2) ein.
Haartyp Temperatur
Geschädigt, gefärbt, entfärbt,
dünn
Normal von +140 °С bis +180 °С
Für professionelles Stylingvon +180 °С bis +200 °С
von +120 °С bis +140 °С
• Wenn sich die Arbeitselemente (1) bis die
eingestellte Temperatur erwärmen, leuchten die
Temperaturanzeigen an der Skala (4) konstant.
• Einige Nutzhinweise
- Benutzen Sie den Multistyler nur zum Stylen
von trockenem Haar, wenn das Haar nass ist
und die erhitzten Oberächen berührt, kocht die
Flüssigkeit schnell auf und beschädigt das Haar.
- Es ist empfohlen, Stylingprodukte mit
Wärmeschutz zu verwenden.
- Mehrmals in der Woche tragen Sie pegende,
feuchtende oder regenerierende Haarmasken auf.
- Spülen Sie das Haar nach dem Waschen mit
einem Kräuterabsud ab. Bei hellem Haar ist ein
Kamillenabsud und bei dunklem Haar ist ein Salbei-,
Eichenrinden- oder Hopfenabsud empfohlen.
Das universelle Mittel für alle Haartypen ist ein
Nesselabsud.
S-FÖRMIGE LOCKEN
• Stellen Sie die Haarwellenintensität mit dem Regler (6)
ein.
• Teilen Sie das Haar in 5-7 cm breite Strähnen.
• Schalten Sie den Multistyler ein, stellen Sie die
gewünschte Erwärmungstemperatur mit den
Tasten (2) «-/+» ein und warten Sie ab, bis sich die
Arbeitselemente (1) erwärmen.
• Ungewöhnliche Wellen werden erschaen, wenn eine
Haarsträhne auf die Arbeitsäche des Multistylers (1)
gelegt und durch zwei zylindrische Elemente gedrückt
wird.
• Trennen Sie die Haarsträhne ab uns drücken Sie sie
zwischen den Arbeitselementen (1) des Multistylers,
beginnend von den Haarwurzeln. Seien Sie vorsichtig
und achten Sie darauf, dass die heißen Elemente (1)
die Kopfhaut nicht berühren, jedoch sich der Multistyler
nicht weit von den Haarwurzeln bendet, da sonst wird
kein Lockenwurzelvolumen erschaen.
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.