BRAYER BR3133VT User Manual [ru]
Instruction manual
Инструкция по эксплуатации
Hot air brush BR3133VT
Фен-щётка BR3133VT
brayer.pro
EN
3EN
СОДЕРЖАНИЕ
EN ......................................................................................................................................3
DE ......................................................................................................................................8
RU ...................................................................................................................................15
KZ ....................................................................................................................................21
HOT AIR BRUSH BR3133VT
The hot air brush is used for styling dry or slightly
damp hair.
DESCRIPTION
1. Operation mode switch 0/С/1/2
2. Light indicator
3. Thermal brush rotation ON-buttons < ˃
4. Protective attachment
5. 40 mm diameter thermal brush
6. Thermo brush release buttons
7. Body
8. Air inlets
9. Hanging loop
ATTENTION!
– Do not use the unit near water in the bathrooms,
showers, swimming pools etc.
– After using the unit in a bathroom, unplug it and
take the power plug out of the mains socket, as the
proximity of water is dangerous even if the unit is
switched o.
– For additional protection it is reasonable to install
a residual current device (RCD) with nominal
operation current not exceeding 30 mA into the mains
of a bathroom. To install it, contact an electrical
technician.
6
4
5
7
3
2
1
9
8
4 5EN EN
SAFETY MEASURES AND OPERATION
RECOMMENDATIONS
Read the operation manual carefully before using the
unit; after reading, keep it for future reference.
• Use the unit for its intended purpose only, as specied
in this manual.
• Mishandling the unit can lead to its breakage and cause
harm to the user or damage to the user’s property,
which is not covered by warranty.
• The hot air brush is intended only for styling of dry and
slightly damp hair, do not use the unit for styling wet
hair or synthetic wigs.
• Make sure that the operating voltage of the unit
indicated on the label corresponds to your home mains
voltage.
• Do not use the unit when you are drowsy.
• Do not use the unit outdoors.
• It is not recommended to use the unit during lightning
storms.
• Protect the unit from impacts, falling, vibrations and
other mechanical stress.
• Never leave the plugged-in hot air brush unattended.
• Do not use the unit near heating appliances, heat
sources or open ame.
• Do not use the unit in places where aerosols are used
or sprayed and close to inammable liquids.
• Do not use the unit near a kitchen sink, in bathrooms,
near swimming pools or other containers lled with
water.
• Do not use the unit while taking a bath.
• Do not hang and do not keep the unit in places where
it can fall into a bath or a sink lled with water; do not
immerse the unit body, power cord or power plug into
water or any other liquid.
• If the unit is dropped into water, unplug it immediately;
only then take the unit out of the water.
• Do not let the power cord touch hot surfaces and sharp
edges of furniture.
• Unplug the unit after usage or before cleaning. When
unplugging the unit, hold the power plug and carefully
remove it from the mains socket, do not pull the power
cord, as this can lead to its damage and cause a short
circuit.
• Do not touch the unit body, the power cord and the
power plug with wet hands.
• Avoid contact of hot surfaces with your face, neck and
other parts of your body.
• Do not direct hot air into eyes or other heat-sensitive
body parts.
• The attachment gets hot during operation. Allow it to
cool down before removal.
• Never insert any foreign objects into any openings in the
unit’s body.
• Do not block the air inlets of the hot air brush and do not
place it on a soft surface, where the air inlets may be
blocked. Keep the air inlets free of lint, dust and hair etc.
• Clean the unit regularly.
• Unplug the unit after usage and before cleaning.
• For child safety reasons, do not leave polyethylene bags
used as packaging unattended.
ATTENTION!
Do not allow children to play with polyethylene bags
or packaging lm. Danger of suocation!
• The hot air brush is not intended for usage by children.
• Do not leave children unattended to prevent using the
unit as a toy.
• Do not allow children to touch the operating surface,
the unit’s body, the power cord or the power plug during
operation of the unit.
• Be especially cautious when children or disabled
persons are near the operating unit.
• During and between the operation cycles of the unit,
place it out of reach of children.
• The unit is not intended for usage by physically or
mentally disabled persons (including children) or by
persons lacking experience or knowledge unless they
are supervised by a person responsible for their safety
or have been instructed by such person on the usage
of the unit.
• Regularly check the integrity of the power cord.
• If the power cord is damaged, it should be replaced by
the manufacturer, a maintenance service or by similar
qualied personnel, to avoid danger.
• Do not repair the unit by yourself. Do not disassemble
the unit by yourself; in case of any malfunction or if
the unit is dropped, unplug it and apply to the service
center.
• To avoid damage, transport the unit in the original
package only.
• Keep the unit in a dry cool place out of reach of children
and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, DO NOT USE THE UNIT FOR COMMERCIAL
OR LABORATORY PURPOSES.
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative
temperature, unpack it and wait for 3 hours before
using it.
• Unpack the unit and remove all the packaging
materials.
• Keep the original package.
• Check the delivery set.
• Read the safety measures and operating
recommendations.
• Examine the unit for damages; if the unit is damaged,
do not plug it into the mains.
• Make sure that the indicated specications of the
power supply voltage of the unit correspond to the
specications of your mains. When the unit is powered
from 60 Hz frequency mains, no additional actions are
necessary.
• Wipe the unit with a clean, slightly damp cloth to
remove dust, and then wipe it dry.
• Unwind the power cord to its full length when using the
unit.
USING THE HOT AIR BRUSH
• For good results, wash your hair with shampoo, wipe it
with a dry towel, dry with a hairdryer and comb it, then
start styling your hair.
6 7EN EN
• Unwind the power cord completely.
• Remove the protective cover (4). Make sure that the
installed thermal brush (5) is xed properly.
• Set the operation mode switch (1) into the 0 position.
• Insert the power plug into the mains socket.
• Using the switch (1), select the required operation
mode. When the hot air brush is switched on, the light
indicator (3) lights up:
- «0» – the hairdryer is o
- «C» – «cool air» supply
- «1» – low temperature
- «2» – high temperature
- Buttons < ˃ (2) activate clockwise/counterclockwise
rotation of the thermal brush (5) (5). During the
operation, press and hold down button (2), the brush
(5) will rotate in the required direction.
Note: during the rst use, the heating element may
produce a foreign smell and a small amount of smoke, this
is normal and it is not a warranty event.
• Divide the hair into locks.
• Depending on your hair type, select the necessary
operation mode with the switch (1).
• Wind a hair lock around the installed thermal brush (5),
select the brush (5) rotation direction with the buttons
(2) < ˃; when the hair lock is wound around the brush
(5), release button (2) and the thermal brush (5) will
stop rotating.
• To x the lock, set the operation mode switch (1) to the
position «C», «cool air» supply.
• Switch the hot air brush o by setting the operation
mode switch (1) to the position «0».
• Take the hair lock o the thermal brush (5),
simultaneously pressing the release buttons (6)
• Place the protective attachment (4) on the thermo brush
(5)
• Notes:
- if you have trouble taking the thermal brush (5) from
the hair, turn the unit o by setting the switch (1) to
the position «0», Remove the installed thermo brush
(5) by simultaneously pressing the release buttons (6)
and carefully remove it from the hair lock.
- during operation, avoid contact of the hot surface of
the thermal brush (5) with your face, neck and other
parts of your body.
• After you nish using the unit, set the switch (1) to the
position «0» and unplug the unit.
• Wait until the thermal brush (5) cools down.
• Place the protective attachment (4) on the thermo brush
(5)
OVERHEATING PROTECTION
• The overheating protection switches the unit o if the
outgoing air is too hot.
• If the hot air brush turns o during operation, set the
switch (1) to the position «0», unplug the unit and make
sure that the air inlets and outlets (8) are unblocked.
• Let the unit cool down for 10-15 minutes and switch it on
again. Do not block the air inlets during the unit operation
and do not let hair be caught into the air inlets (8).
CLEANING AND MAINTENANCE
• The hot air brush is intended for household use only.
• Set the switch (1) to the position «0» and unplug the
unit, wait until the installed thermal brush (5) cools
down.
• Remove the installed thermo brush (5) by
simultaneously pressing the release buttons (6).
• Clean the thermo brush (5) o hair and install it back
to its place.
• Wipe the unit body (7) with a slightly damp cloth, and
then wipe it dry.
• Clean the air inlets (8) with a brush (5).
• Do not immerse the unit into water or any other
liquids.
• Do not use abrasives and solvents to clean the unit’s
body (7) and the thermal brushes (5).
STORAGE
• Disconnect the unit from the mains and clean it.
• Never wind the power cord around the hot air brush,
as this can damage the cord or the unit’s body.
• For convenient storage, the hot air brush has a
hanging loop (9) that you can hang it on, provided
that in this position the unit is not exposed to water.
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
DELIVERY SET
1. Hot air brush – 1 pc
2. 40 mm diameter thermal brush – 1 pcs
3. Protective attachment – 1 pc.
4. Instruction manual – 1 pc
TECHNICAL SPECIFICATIONS
• Supply voltage: 220-240 V, ~ 50/60 Hz
• Rated input power: 1000 W
ATTENTION!
Do not allow children to play with
polyethylene bags or packaging lm.
Danger of suocation!
RECYCLING
To prevent possible damage to the
environment or harm to the health of people
by uncontrolled waste disposal, after service
life expiration of the unit or the batteries (if
included), do not discard them with usual
household waste, deliver the unit and the
batteries to specialized centers for further recycling.
The waste generated during the disposal of the unit is
subject to mandatory collection and consequent disposal
in the prescribed manner.
For further information about recycling of this product
apply to a local municipal administration, a disposal
service or to the shop where you purchased this product.
The manufacturer reserves the right to change the
design, structure and specications not aecting
general principles of the unit operation, without prior
notice.
The unit operating life is 3 years
8 9DE DE
DE
WARMLUFTBÜRSTE BR3133VT
Die Warmluftbürste wird fürs Styling von trockenem
oder leicht feuchtem Haar benutzt.
BESCHREIBUNG
1. Betriebstufenschalter 0/C/1/2
2. Kontrolleuchte
3. Einschalttasten der Thermobürste-Drehung < ˃
4. Schutzaufsatz
5. Thermobürste mit 40 mm im Durchschnitt
6. Thermobürste-Verriegelungstasten
7. Gehäuse
8. Lufteintrittsönungen
9. Aufhängeöse
ACHTUNG!
– Das Gerät in der Nähe des Wassers in
Badezimmern, Duschräumen, Wasserbecken usw.
nicht benutzen.
– Nach der Nutzung des Geräts im Badezimmer
schalten Sie es aus und ziehen Sie den Netzstecker
aus der Steckdose heraus, weil die Nähe des
Wassers gefährlich ist, wenn das Gerät sogar mittels
Netzschalter ausgeschaltet ist.
– Als zusätzlicher Schutz ist es zweckmäßig,
den FI-Schalter mit Nennstrom bis 30 mA im
Stromversorgungskreis des Badezimmers
aufzustellen; wenden Sie sich dafür an einen
Elektriker.
6
4
5
3
2
1
9
SICHERHEITSHINWEISE UND HINWEISE ZUR
BEDIENUNG
Bevor Sie das Gerät benutzen, lesen Sie zuerst
die Bedienungsanleitung aufmerksam durch und
bewahren Sie sie zum späteren Gebrauch auf.
• Benutzen Sie dieses Gerät bestimmungsmäßig und
laut der Bedienungsanleitung.
• Missbrauch des Geräts kann zu seiner Störung
führen, den Benutzer oder seinem Eigentum
Schaden bringen und ist kein Garantiefall.
• Die Warmluftbürste ist nur fürs Styling von trockenem
7
8
und leicht feuchtem Haar bestimmt; benutzen
Sie das Gerät fürs Styling von nassem Haar oder
synthetischen Perücken nicht.
• Vergewissern Sie sich, dass die auf dem
Bezeichnungszettel angegebene Betriebsspannung
und die Netzspannung übereinstimmen.
• Benutzen Sie das Gerät nicht, wenn Sie schläfrig
sind.
• Es ist nicht gestattet, das Gerät draußen zu
benutzen.
• Es ist nicht empfohlen, das Gerät bei Gewitter zu
benutzen.
• Schützen Sie das Gerät vor Stößen, Stürzen,
Vibrationen und anderen mechanischen
Einwirkungen.
• Lassen Sie die ans Stromnetz angeschlossene
Warmluftbürste nie unbeaufsichtigt.
• Benutzen Sie das Gerät in direkter Nähe von
Heizgeräten, Wärmequellen oder oenem Feuer
nicht.
• Das Gerät an den Orten, wo Sprays verwendet
werden, sowie in der Nähe von leichtentzündbaren
Flüssigkeiten nicht benutzen.
• Benutzen Sie das Gerät in der Nähe von Spülbecken,
in Badezimmern und neben Wasserbecken oder
anderen mit Wasser gefüllten Behältern nicht.
• Das Gerät beim Baden nicht benutzen.
• Hängen Sie das Gerät nicht da an und bewahren
Sie es nicht da auf, wo es in eine mit Wasser gefüllte
Wanne oder Waschbecken stürzen kann; tauchen
Sie das Gerätegehäuse, das Netzkabel oder den
Netzstecker ins Wasser oder jegliche andere
Flüssigkeit nicht ein.
• Falls das Gerät ins Wasser gefallen ist, ziehen Sie
den Netzstecker aus der Steckdose sofort heraus,
erst danach holen Sie das Gerät aus dem Wasser
heraus.
• Achten Sie darauf, dass das Netzkabel heiße
Oberächen und scharfe Möbelkanten nicht berührt.
• Trennen Sie das Gerät nach dem Gebrauch oder
vor der Reinigung vom Stromnetz ab. Wenn Sie
das Gerät vom Stromnetz abtrennen, halten Sie
den Netzstecker fest und ziehen Sie ihn aus der
Steckdose vorsichtig heraus; ziehen Sie das
Netzkabel nicht, da es zu seiner Beschädigung und
einem Kurzschluss führen kann.
• Berühren Sie das Gerätegehäuse, das Netzkabel
und den Netzstecker mit nassen Händen nicht.
Loading...