BRAYER BR1242 User Manual [ru]
brayer.su
Instruction manual Инструкция по эксплуатации
Blender BR1242
Блендер BR1242
Содержание
en |
......................................................................................................................................3 |
de.................................................................................................................................... |
11 |
RU.................................................................................................................................... |
21 |
kz..................................................................................................................................... |
30 |
BLENDER BR1242
The immersion blender included into the blender set is intended for whisking, mixing, chopping and combined processing of liquid and solid products.
DESCRIPTION
1.Blender attachment
2.Motor unit
3.«TURBO» button
4.ON/OFF button
5.Rotation speed control knob
6.Whisk attachment gear
7.Whisk attachment
8.Chopper geared lid
9.Chopper bowl
10.Chopping knife
11.Cup
enen 3
5 
4 3 
11
2 
|
6 |
|
8 |
1 |
7 |
|
9 |
|
10 |
4 en
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
Read the operation instructions carefully before using the unit, after reading keep them for future reference.
•Use the unit for its intended purpose only, as it is stated in this manual.
•Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
•Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
ATTENTION! Continuous operation time should not exceed 60 seconds while using the blender attachment, 30 seconds while using the chopper attachment and 1 minute while using the whisk attachment. Make at least a 3-minute break between operation cycles.
•Do not use the unit outdoors.
•It is recommended not to use the unit during lightning storms.
•Protect the unit from impacts, falling, vibrations and other mechanical stress.
•Never leave the unit connected to the mains unattended.
•Do not use the unit near heating appliances, heat sources or open flame.
•Do not use the unit in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
•Do not use the unit in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
•If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.
•Do not let the power cord touch hot surfaces and sharp edges of furniture.
•Unplug the unit after usage or before cleaning. When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
•Do not touch the unit body, the power cord and the power plug with wet hands.
•Before using the unit for the first time, thoroughly wash all the removable attachments and containers that will contact food.
•Use only the parts supplied.
•Do not touch rotating parts of the unit. Do not let hair or free hanging clothes get into the rotation area of the blender attachment knife or whisk.
•Before using the unit, make sure that the attachments are installed properly and fixed.
•Place the chopper bowl on a flat and steady surface.
•Put the products into the chopper bowl before switching the unit on. Do not switch the unit on if the chopper bowl is empty.
•Cool down hot products before putting them into the chopper bowl.
•Watch the amount of products put in the chopper bowl and the level of poured liquids.
•Cutting edges of the chopping knife and the blender attachment are sharp and dangerous. Be careful while using the chopping knife and the blender attachment.
•If the chopping knife stops during the unit operation, switch the unit off, unplug it and open the geared lid, remove the product which is hindering the knife rotation. If the chopping knife or blender attachment rotation is hindered, it is recommended to add some water, juice, liquor etc. into the chopper bowl or the container used with the blender attachment.
•Remove the motor unit from the chopper bowl only after disconnecting the motor unit from the mains.
•Do not place the chopper bowl and the measuring cup into a microwave oven.
•Do not put the attachments and bowls in a dishwashing machine.
•For children safety reasons do not leave polyethylene bags used as a packaging unattended.
Attention!
Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!
en 5
•The unit is not intended for usage by children.
•Do not leave children unattended to prevent using the unit as a toy.
•Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
•Be especially careful if children or disabled persons are near the operating unit.
•During the unit operation and breaks between operation cycles, place the unit out of reach of children.
•The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
•From time to time check the power cord integrity.
•If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
•Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
•To avoid damages, transport the unit in the original package.
•Keep the unit in a dry cool place out of reach of children and disabled persons.
6 en
THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.
•Unpack the unit and remove all the packaging materials.
•Keep the original package.
•Read the safety measures and operating recommendations.
•Check the delivery set.
•Examine the unit for damages, in case of damage do not plug it into the mains.
•Make sure that the indicated specifications of the power supply voltage of the unit correspond to the specifications of your mains.
•Before using the unit wash the whisk attachment (7), the bowl (9), the chopping knife (10) and the cup (11) with warm water and a neutral detergent and dry them.
•Wash only the lower part of the blender attachment (1), clean the outer surface with a slightly damp cloth. Never immerse the blender attachment (1) into water or any other liquids completely.
•Wipe the motor unit (2), the chopper geared lid (8), the whisk attachment gear (6) with a soft, slightly damp cloth and then wipe them dry.
ATTENTION!
Do not immerse the blender attachment (1), the motor unit (2), the chopper geared lid (8), the whisk attachment gear (6), the power cord and the power plug into water or any other liquids.
USING THE BLENDER ATTACHMENT
Continuous operation time should not exceed 60 seconds while using the blender attachment
(1). Make at least 3 minutes break between the operation cycles.
•Use the blender attachment (1) for making sauces, mayonnaise, fruit puree, baby food, mixing various ingredients and for processing fruit and vegetables containing enough liquid.
Before installing the blender attachment (1), make sure that the power plug is not inserted into the mains socket.
•Insert the blender attachment (1) into the motor unit (2), and turn it counterclockwise as far as it will go, make sure that the attachment is fixed properly (fig.
1).
•Insert the power plug into the mains socket.
•Immerse the blender attachment (1) into the bowl with food that you want to chop/mix; you can also put the food in the measuring cup (11).
ATTENTION!
Hold the motor unit (2) with the blender attachment
(1)vertically while processing the food.
•To switch the unit on, press and hold down the button (4) . Use this operation mode for mixing liquid products.
•When you press and hold the button (4) you can control the attachment rotation speed by turning the control knob (5). Use this operation mode for processing of liquid and solid products.
•For operation at the maximal rotation speed, press and hold down the button (3) «TURBO».
•Notes:
-- products should be put into the bowl before the unit is switched on. The amount of products to be processed should not exceed 2/3 of the capacity of the bowl in which they are processed.
-- before chopping and mixing peel the fruit, remove inedible parts, such as stones, and cut fruit into 15x15x15 mm cubes. Put them into a bowl and add some juice or water. The maximal amount of products should not exceed 350 g and 250 ml of water or juice.
-- do not chop or mix frozen food.
ATTENTION!
When chopping hard vegetables, for example, car rots — cut the carrot into small 15x15x15 mm pieces
and put them in the cup (11). The maximal weight of the carrot should not exceed 250 g. Add 350 ml of water.
en 7
•To switch the blender attachment (1) rotation off release the button (3 or 4).
•After you finish the unit operation, take the power plug out of the mains socket and remove the blender attachment (1), turning it clockwise.
•ATTENTION!
-- Do not remove the blender attachment (1) during the unit operation.
-- To avoid damaging the knives of the blender attachment (1) do not process very hard products, such as cereals, rice, coffee beans, hard cheese, frozen food etc.
-- If the foodstuffs are hard to chop with the blender attachment (1), add some water, juice, liquor etc.
USING THE CHOPPER
Continuous operation time should not exceed 30 seconds while using the chopper attachment. Make at least 3 minutes break between the operation cycles.
•The attachment is used to chop meat, cheese, onion, herbs, garlic, carrots, walnuts, prunes, vegetables
or fruit.
ATTENTION!
Do not chop very hard products, such as nutmegs, coffee beans, cereals, frozen food or ice.
8 en
Preparing the food before chopping:
•Remove bones, veins, cartilage and fat from meat.
•Cut meat, cheese, onions, vegetables or fruit into pieces approximately 60x20x20 mm in size. Maximal weight of the meat should not exceed 200 g.
•Remove stems of herbs, shell nuts.
Chopping
Before assembling the chopper, make sure that the power plug is not inserted into the mains socket.
•Place the chopper bowl (9) on a flat and steady surface.
•Install the chopping knife (10) on the axis inside the bowl (9).
Attention!
The blades of chopping knife (10) are very sharp! Always hold the chopping knife (10) by the plastic end.
•Put the products into the bowl (9).
•Note: — do not switch the unit on when the bowl (9) is empty.
•Install the geared lid (8) on the bowl (9).
•Install the motor unit (2) on the geared lid (8) feeding chute, turn the motor unit (2) clockwise until bumping, make sure that the motor unit (2) is fixed properly.
Install the motor unit (2) evenly in vertical position
(fig. 2).
•Insert the power plug into the mains socket.
•To switch the unit on, press and hold down the button
(4).
•When you press and hold the button (4) you can control the chopping knife (10) rotation speed by turning the control knob (5).
•For operation at the maximal rotation speed, press and hold down the button (3) «TURBO».
•During the unit operation hold the motor unit (2) with one hand and the chopper bowl (9) with the other hand.
•Release the button (3 or 4) to switch off.
•After the unit operation, wait till the chopping
•knife (10) completely stops rotating.
•Remove the power plug from the mains socket.
•Disconnect the motor unit (2) from the geared lid (8) by turning the motor unit (2) counterclockwise.
•Remove the geared lid (8) from the bowl (9).
•Carefully remove the chopping knife (10) from the bowl (9) holding it by the plastic end.
•Take the chopped products out of the bowl (9).
USING THE WHISK ATTACHMENT
•Continuous operation time should not exceed 1 minute while using the whisk attachment (7). Make at least a 3-minute break between operation cycles.
ATTENTION!
Do not use the whisk attachment (7) to knead tight dough.
•Use the whisk attachment (7) only for beating egg whites, making biscuit dough or for mixing ready desserts.
Before installing the whisk attachment (7), make sure that the power plug is not inserted into the mains socket.
•Insert the whisk attachment (7) into the whisk gear
•Insert the whisk gear (6) into the motor unit (2) and turn it counterclockwise, make sure that the gear (6) and the whisk (7) are fixed properly (fig. 3).
•Insert the power plug into the mains socket.
•Immerse the whisk attachment (7) into a suitable bowl with food. You can put the foodstuffs into the cup (11).
•To switch the unit on, press and hold down the button
(4).
•When you press and hold the button (4) you can control the attachment rotation speed
•by turning the control knob (5).
•For operation at the maximal rotation speed, press and hold down the button (3) «TURBO».
•Release the button (3 or 4) to switch off.
•After you finish using the unit, disconnect the power plug from the mains socket, disconnect the whisk gear (6) from the motor unit (2) by turning the gear
(6)clockwise.
•Remove the whisk attachment (7) from the gear (6).
en 9
CLEANING
Attention!
The blades of the chopping knife (10) are very sharp and may be dangerous. Handle the chopping knife
(10)very carefully!
•Unplug the unit after you finish using it.
•Wash the whisk attachment (7), the chopper bowl (9), the chopping knife (10) and the cup (11) with warm water and a neutral detergent and dry them.
•Wash only the lower part of the blender attachment (1), clean the outer surface with a slightly damp cloth. Never immerse the blender attachment (1) into water or any other liquids completely.
•Wipe the motor unit (2), the geared lid (8) and the whisk attachment gear (6) with a soft slightly damp cloth and then wipe them dry.
•After processing salty or sour products, it is necessary to rinse the blender attachment (1) or the chopping knife (10) with water immediately.
•While possessing products with dyeing properties (for instance, carrot or beetroot) the attachments and bowls can get colored, wipe the attachments and the bowls with a cloth, dampened in vegetable oil; after that wash the attachments and bowls with a neutral detergent, rinse and dry them.
•Do not immerse the motor unit (2), the gear (6), the geared lid (8) into any liquids, do not wash them under water jet or in a dishwashing machine.
10en
•Do not use abrasives and solvents to clean the motor unit body (2) and the removable parts.
STORAGE
•Clean the unit parts before taking it away for long storage.
•Do not wind the power cord around the motor unit
(2).
•Keep the unit in a dry cool place out of reach of children and disabled persons.
DELIVERY SET
1.Motor unit — 1 pc.
2.Blender attachment — 1 pc.
3.Whisk gear — 1 pc.
4.Whisk attachment — 1 pc.
5.Geared lid — 1 pc.
6.Chopping knife — 1 pc.
7.Chopper bowl — 1 pc.
8.Cup — 1 pc.
9.Instruction manual — 1 pc.
TECHNICAL SPECIFICATIONS
•Power supply: 220-240 V, ~ 50-60 Hz
•Rated input power: 800 W
RECYCLING
To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after
expiration of the service life of the unit or the
batteries (if included), do not discard them with usual household waste, but take the
unit and the batteries to specialized stations for further recycling.
The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product.
The manufacturer reserves the right to change the appearance, design and specifications not affecting general operation principles of the unit, without prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number. In case of any malfunctions promptly apply to the authorized service center.
STABMIXER BR1242
Der im Stabmixer-Satz enthaltene Stabmixer wird zum Schlagen, Mixen, Zerkleinern und
gemeinsamen Bearbeiten von flüssigen und festen
Nahrungsmitteln verwendet.
BESCHREIBUNG
1.Stabmixeraufsatz
2.Motoreinheit
3.Geschwindigkeitseinschalttaste «TURBO»
4.Geschwindigkeitseinschalttaste
5.Drehgeschwindigkeitsregler
6.Schlagbesengetriebe
7.Schlagbesenaufsatz
8.Getriebedeckel des Zerkleinerers
9.Zerkleinerungsbehälter
10.Zerkleinerungsmesser
11.Becher
dede 11
5 
4 3 
11
2 
|
6 |
|
8 |
1 |
7 |
|
9 |
|
10 |
12 de
SICHERHEITSHINWEISE UND BEDIENUNGSANLEITUNG
Bevor Sie das Gerät benutzen, lesen Sie zuerst die Bedienungsanleitung aufmerksam durch und bewahren Sie sie zum späteren Gebrauch auf.
•Benutzen Sie das Gerät nur bestimmungsmäßig und laut dieser Bedienungsanleitung.
•Missbrauch des Geräts kann zu seiner Störung führen, den Benutzer oder sein Eigentum beschädigen und ist kein Garantiefall.
•Vergewissern Sie sich, dass die auf dem Bezeichnungszettel angegebene Betriebsspannung und die Netzspannung übereinstimmen.
ACHTUNG! Der Betrieb soll 60 Sekunden mit dem Stabmixeraufsatz, 30 Sekunden mit dem Zerkleinerungsaufsatz und 1 Minute mit dem
Schlagbesenaufsatz nicht überschreiten.
Machen Sie eine mindestens 3-Minuten- Betriebszyklenpause.
•Es ist nicht gestattet, das Gerät draußen zu benutzen.
•Es ist nicht empfohlen, das Gerät bei Gewitter zu benutzen.
•Schützen Sie das Gerät vor Stößen, Stürzen, Vibrationen und anderen mechanischen Einwirkungen.
•Lassen Sie das ans Stromnetz angeschlossene Gerät nie unbeaufsichtigt.
•Benutzen Sie das Gerät in direkter Nähe von Heizgeräten, Wärmequellen oder offenem Feuer nicht.
•Es ist verboten, das Gerät an den Orten, wo Sprays verwendet werden, sowie in der Nähe von leichtentzündbaren Flüssigkeiten zu benutzen.
•Benutzen Sie das Gerät in der Nähe von Spülbecken, in Badezimmern und neben den Wasserbecken oder anderen mit Wasser gefüllten Behältern nicht.
•Falls das Gerät ins Wasser gefallen ist, ziehen Sie den Netzstecker aus der Steckdose sofort heraus, erst danach holen Sie das Gerät aus dem Wasser heraus. Wenden Sie sich an einen autorisierten Kundendienst, um das Gerät prüfen oder reparieren zu lassen.
•Achten Sie darauf, dass das Netzkabel heiße
Oberflächen und scharfe Möbelkanten nicht berührt.
•Trennen Sie das Gerät nach dem Gebrauch oder vor der Reinigung vom Stromnetz ab. Wenn Sie das Gerät vom Stromnetz abtrennen, halten Sie den Netzstecker fest und ziehen Sie ihn aus der Steckdose vorsichtig heraus; ziehen Sie das Netzkabel nicht, da es zu seiner Beschädigung und einem Kurzschluss führen kann.
•Berühren Sie das Gerätegehäuse, das Netzkabel und den Netzstecker mit nassen Händen nicht.
•Vor der ersten Gerätenutzung spülen Sie alle mit den Nahrungsmitteln zu kontaktierenden abnehmbaren Aufsätze und Behälter sorgfältig durch.
•Benutzen Sie nur die mitgelieferten Teile.
•Berühren Sie keine drehenden Geräteteile. Halten Sie Haar oder frei hängende Kleiderstücke vom Drehbereich des Messers des Stabmixeraufsatzes oder des Schlagbesens fern.
•Vergewissern Sie sich vor der Gerätenutzung, dass die Aufsätze richtig aufgestellt und befestigt sind.
•Stellen Sie den Zerkleinerungsbehälter auf eine ebene und standfeste Oberfläche auf.
•Legen Sie die Nahrungsmittel in den Zerkleinerungsbehälter vor der Geräteeinschaltung ein, es ist verboten, das Gerät ohne Nahrungsmittel im Zerkleinerungsbehälter einzuschalten.
•Kühlen Sie heiße Nahrungsmittel ab, bevor Sie sie in den Zerkleinerungsbehälter einlegen.
•Beachten Sie die Nahrungsmittelmenge und den Flüssigkeitenfüllstand im Zerkleinerungsbehälter.
•Die Schneidkanten des Zerkleinerungsmessers und des Stabmixeraufsatzes sind scharf und gefährlich, gehen Sie mit den Zerkleinerungsmessern und dem Stabmixeraufsatz vorsichtig um.
•Wenn das Zerkleinerungsmesser während des Betriebs stoppt, schalten Sie das Gerät aus, ziehen Sie den Netzstecker aus der Steckdose heraus, nehmen Sie den Getriebedeckel ab und
entfernen Sie das die Zerkleinerungsmesserdrehung verhindernde Nahrungsmittel. Bei schwer drehendem Zerkleinerungsmesser und Stabmixeraufsatz ist
es empfohlen, Wasser, Saft, Brühe usw. in den Zerkleinerungsbehälter oder in den Behälter mit verwendetem Stabmixeraufsatz einzugeben.
de 13
•Nehmen Sie die Motoreinheit vom Zerkleinerungsbehälter erst nach dem Abtrennen der Motoreinheit vom Stromnetz ab.
•Es ist nicht gestattet, den Zerkleinerungsbehälter und den Messbecher in den Mikrowellenofen zu stellen.
•Es ist nicht gestattet, die Aufsätze und die Behälter in der Geschirrspülmaschine zu waschen.
•Aus Kindersicherheitsgründen lassen Sie die als Verpackung verwendeten Plastiktüten nie ohne Aufsicht.
Achtung!
Lassen Sie Kinder mit Plastiktüten oder Verpackungsfolien nicht spielen. Erstickungsgefahr!
•Das Gerät ist nicht für Kinder bestimmt.
•Beaufsichtigen Sie Kinder, damit sie das Gerät als Spielzeug nicht benutzen.
•Lassen Sie Kinder die Arbeitsfläche, das
Gerätegehäuse, das Netzkabel oder den Netzstecker während des Gerätebetriebs nicht berühren.
•Besondere Vorsichtsmaßnahmen sind in den Fällen angesagt, wenn sich Kinder oder behinderte Personen während des Gerätebetriebs in der Nähe aufhalten.
•Während des Betriebs und der Pausen zwischen den Betriebszyklen stellen Sie das Gerät an einen für Kinder unzugänglichen Ort auf.
•Dieses Gerät ist für Personen (darunter Kinder) mit Körper-, Nervenund Geistesstörungen
Loading...