Caution : You must read this before you proceed
ROCKING CHAIR
Page 1 OF 10
Label Picture Description QTY
A Frame 1
B Back 1
C Seat 1
D
Left Rocking Base
1
E Right Rocking Base 1
Label Picture Description QTY
① Bolt (M8*70MM) 3
② Screw (M4*40mm) 11
Page 2 OF 10
③ Spring Washer 4
④ Washer 4
⑤ Allen Key 1
⑥ Screwdriver 1
Before
Beginning
Assembly:
Marked 'longer'
Rocking Base ends marked 'longer' must be attached to Back Legs
Page 3 OF 10
Step 1
Overview
This Rocking Chair has multiple parts and may require up to 30
minutes to assemble. To give you an overview of the Arm Chair
parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to
familiarise yourself with the parts and steps before assembly.
A
B
C
Front Facing
D
E
Seat (C)
Back (B)
Frame (A)
Left Rocking Base(D)
Right Rocking Base(E)
Marked 'longer'
Marked 'longer'
Page 4 OF 10
Step 2
Place the Frame(A), Back(B), Seat(C), Left Rocking Base(D) and
Right Rocking Base(E) on a clean, non-marring surface.
Carefully peel away the Dust Cover from the edge of the Seat(C)
and put it aside.
2.1) Align the mounting positions of the Back(B) with Seat(C) and
attach them using Bolts(①), Spring Washers(③) and Washers(④)
with Allen Key(⑤).
Note: If the mounting positions cannot be aligned well and
hinder the installation, then sway the Seat(C) lightly when
locking the Bolts, this action could help prevent the Bolts
from getting stuck and ensure smooth assembly.
2.2) Tighten the Bolts fully in a sequential manner; then smooth
down the Dust Cover with your hands on all four edges of the Seat
bottom.
⑤
Back(B)
Seat(C)
2.1
2.2
Back(B)
Seat(C)
Page 5 OF 10
Step 3
Place the assembled Seat(C) and Back(B) on the side of a table,
with the Back(B) facing down.
3.1) Place the Frame(A) onto the assembled Seat(C) and Back(B)
as shown in the picture.
3.2) Attach Frame(A) to Seat(C) using Screws(②) with
Screwdriver(⑥).
Note: If there are gaps between the Frame(A) and Seat(C)
which hinders installation, then pull the Seat(C) upwards into
the Frame(A), this action helps to ensure there are no gaps
between them.
Do not fully tighten the Screws.
3.1
Seat(C)
Frame(A)
Table
Back(B)
Seat(C)
Frame(A)
3.2
⑥
②
Seat(C) and Back(B) stuck in the middle of the Frame(A)
Page 6 OF 10
Step 4
Step 5
Attach Frame(A) to Back(B) using Screws(②) with
Screwdriver(⑥).
Note: Please press the Back(B) to Frame(A) before attaching.
Do not fully tighten the Screws.
Table
Frame(A)
Seat(C)
Back(B)
⑥
②
Left Rocking Base(D)
Right Rocking Base(E)
Frame(A)
Seat (C)
Table
⑥
②
Marked 'longer'
Page 7 OF 10
Note: The distance from the back mounting position to the
Rocking Base end is 17.5cm. It is longer than the front
mounting position to the head. The Back Legs must have the
longer ends to help prevent the Rocking Chair from tipping
over.
Align the mounting positions of the Left Rocking Base(D) with the
Frame(A) and attach using Screws(②) with Screwdriver(⑥).
Do not fully tighten the Screws.
Repeat this process with the Right Rocking Base(E).
Note: There are two mounting sites on the Rocking Base,
please insert the back foot into the back mounting position
first and then do the same for the front foot, this action
should ensure smoother assembly.
Step 6
Seat (C)
Back (B)
Frame (A)
Left Rocking Base(D)
Right Rocking Base(E)
Marked 'longer'
Test for Stability
Page 8 OF 10
Step 7
Inspect the Rocking Chair and make sure all parts are adequately
connected.
Gently and carefully, sit into to the Rocking Chair.
This would help to align all the parts at all joints.
Then get off the Rocking Chair, and place it facedown.
Proceed to tighten all Bolts and Screws at all joints in a
sequential manner.
If there are still wobbles, loosen the Bolts and Screws and
execute this same process.
Your Rocking Chair is ready for use.
This Rocking Chair can only be used on a flat, level surface.
Page 9 OF 10
Page 1 OF 1
Loading...