Page 1
Installation Guide
LED INFO & WARNINGS
Please read and comprehend the entire manual before attempting to
•
assemble, operate, or install the product.
Make sure that you have all necessary parts by checking the parts list.
•
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
We highly recommends to use a qualified, licensed electrician to install the
fixture.
We
recommends to install the fixture on its own independent circuit.
Do not install the fixture on the same circuit with other appliances, or
HVAC systems.
Do not remove or replace manufactured driver that is provided with the
•
fixture.
•
We recommends ELV (Electric Low Voltage) type dimmers for this
fixture.
Shut “OFF” the electricity at main fuse box.
•
•
Place the wall switch in the “OFF” position of the room you are installing
the fixture.
Parts List
Mounting Bracket
A
C
B
D E
F
G
A.
Plastic Anchors x 5
B.
Anchor Screws x 5
C.
Outlet Screws x 3
D.
Wire Connectors x 3
E.
Ground Screw x 1
F.
Canopy Screws x 4
G.
Circuit Box
ON
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
PHILLIPS
SCREW DRIVER
DRILL
LADDER
Page 2
Fixture Diagram
Mounting
A
Bracket
F
Ground
Screw
C
Outlet
D
Sc
Wire
E
Connector
B
Anchor
Screw
rew
Plastic
Anchors
Ceiling
Canopy
G
Screw
Page 3
Step 2. Connect Wires
Black
Ceiling
(Line Wire)
Ground
F
Screw
Bare Copper
(Ground Wire)
White
G
(Neutral Wire)
Wire
E
Connector
Supply Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire)
from outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral
Wire) from outlet box.
Ground Wires:
Connect Bare Copper (Ground Wire) from fixture to Green
or Bare Copper (Ground Wire) from outlet box.
Twist wires together clockwise and secure with wire
connector (E).
Installer Tip (1): If ground wire is not available in outlet
box, then secure Bare Copper (Ground Wire) from fixture to
ground screw (F) on mounting bracket (A).
Installer Tip (2): It is recommended that two installers are required to
install the fixture. One installer to hold the fixture, and the second installer
to connect the wires.
Page 4
Step 3. Mount Fixture
Canopy
Mounting
A
Bracket
Ceiling
Attach fixure to mounting bracket (A). Secure
fixture with canopy screws (G).
Outlet Box
Mounting
A
Bracket
Canopy
G
Screw
Step 4. Turn Power ON
Turn electricity “ON” at main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the fixture.
Circuit Box
ON
Ceiling
Canopy
ON
Page 5
Step 1. Install Mounting Bracket
Outlet Box
Mounting
A
Bracket
Raise mounting bracket (A) to the ceiling. Mark location for
the plastic anchors (B). Drill holes for plastic anchors (B).
Insert plastic anchors (B) into hole.
Outlet Box
B
Plastic
Anchors
Ceiling
Ceiling
Mounting
A
Bracket
Attach mounting bracket (A) to outlet box with oulet screws
(D). Screw anchor screws (C) into plastic anchors (B) to
secure mounting bracket (A).
Anchor
C
Screw
Outlet
D
rew
Sc
Loading...