Page 1
1
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
COLLECTION
MADRID
APPLICATION MODEL NO.
CEILING
WHAT WE PROVIDE
Mounting Hardware
•
• Mounting Bracket
• Marking paper
• LED
Recommended Dimmers
Lutron Skylark
Lutron Diva
Lutron Diva
Lutron Diva
Lutron Skylark
52180LEDD
WHAT YOU NEED
Screwdriver
•
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
Page 2
1
2
2
3
PAPER
ATTACH THE MOUNTING BRACKET
If there is an existing fixture remove it.
Determine the desired location of the fixture. Hold the
paper template to the surface and with a pencil mark
the location of the drywall anchors. Drill a hole and insert
the supplied drywall anchors into the mounting surface.
Position the mounting bracket onto the J-box and secure
with the supplied screws.
CONNECT THE WIRES AND
THE FIXTURE
N
L
Expose the supply wires from the J-box. Gently pull the
supply wires through the hole in the mounting bracket.
Connect the black supply wire to the black fixture wire.
Secure with the supplied wire nuts. Connect the white
supply wire to the white fixture wire. Secure with the
supplied wire nuts. Attach the green J-Box wire around
green hexagonal head screw or connect it to the green
supply grounding wire of the fixture. Secure all wires
with electrical tape (not supplied).
Tuck all wires carefully into the J-Box.
Align the fixture canopy onto the mounting bracket and
secure with the supplied screws.
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
MOUNT
If the fixture is to be removed or replaced,
please ensure that the electricity is
CAUTION
switched off and that the fitting is cool
before touching it.
Loading...