Page 1
Assembly Instructions
____
Caution: You must read this before you proceed
Please look in the corner of box for hardware packs
Extention Table
Caution: This Table is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Table and to prevent damage to the Table, two adults are needed to
execute this action.
1
Page 2
①
②
③
Parts List
____
Label Picture Description QTY
A Table Top 1
B Leg 4
C
Expansion Board of
Table Top
Hardware
Label Picture Description QTY
Bolt (M8x60mm) 9
Washer 9
Allen Key 2
Assembly Preparation
Before Beginning Assembly:
1
2
Page 3
Assembly Steps
____
Overview
Table Top (A)
Expansion Board of
Table Top (C)
Leg (B)
This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of
the Table parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
FRONT FACING
Step 1
Unpack and place all parts on a clean, non-marring surface.
3
Page 4
Step 2
____
Place Table Top(A) facedown, onto a clean, non-marring surface.
Attach Leg(B) to Table Top(A) using Bolts(①), and Washers(②) with Allen Key(③).
Do not fully tighten the Bolt.
Repeat the same process with the remaining three Legs(B).
Step 3
Stand the Table up, with assistance from your adult partner.
Exert pressure floorwards, onto the Table with both your hands.
This pressure will help the Legs and Table Top reach full alignment status.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts in a sequential manner, until evenly secured.
When tightening the Bolts tighten sequentially.
Do not tighten any Bolt fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and excute the same above process.
If the Table is not Stable it could lead to damage to the product.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
4
Page 5
Extention Steps:
____
To Extend the Table:
Step 1
Unlock the Metal Fasteners.
Step 2
With an adult partner, gently pull the Table Top(A) to take out the Expansion Board of Table Top(C) as
shown above.
Caution: Do not Lean on or apply pressure to the Table Top when it is pulled open. This could cause
damage to the product.
5
Page 6
Lock the Metal Fasteners under the Table Top to lock the Expansion Board of Table Top(C) into place as
Step 3
____
3.1) Insert the Expansion Board of Table Top(C) to the Table as shown above.
3.2) Gently push the Table Top(A) until the Top Table(A) fits into the Expansion Board of Table Top(C).
Caution: Keep hands away from the Table Top(A) and Expansion Board of Table Top(A) when pushing
the Table Top to avoid pinching hazards. If you can not push the Table Top(A) inwards, just lightly shake
the Table Top(A).
Step 4
shown in the above picture.
Your Table is extended and is now ready for use.
This Table can only be used on a flat, level surface.
6
Page 7
To Retract the Table:
____
Step 1
Unlock the Metal Fasteners.
Step 2
2.1) With assistance from an adult, gently pull the Top Table(A) outwards as indicated by the arrows
above.
2.2) Take out the Expansion Board of Table Top (C) as shown above.
Caution: Do not Lean on or apply pressure to the Table Top when it is pulled open. This could cause
damage to the product.
7
Page 8
Step 3
____
Turn the Expansion Board of Table Top(C) and located inside of the Table as shown above.
Push the Table Top(A) inwards until both wings of the Table Top(A) align.
Caution: Keep hands away from the Table Top(A) and Expansion Board of Table Top(C ) when
pushing the Table Top to avoid pinching hazards. If you can not push the Table Top(A) inwards,
just lightly shake the Table Top(A).
Step 4
Lock the Metal Fasteners under the Table Top(A) into place as shown in the above picture.
Your Table is retracted and is now ready for use.
This Table can only be used on a flat, level surface.
8
Page 9
____
9
Loading...