Assembly Instructions
Caution: You must read this before you proceed
Extention Table
Caution: This Table is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Table and to prevent damage to the Table, two adults are needed to
execute this action.
1 ____
Label Picture Description QTY
A Table Top 1
B Leg 4
Label Picture Description QTY
① Bolt (M8x60mm) 9
② Washer 9
③ Allen Key 2
Parts List
Assembly Preparation
Before Beginning Assembly:
Hardware
2 ____
Step 1
Unpack and place all parts on a clean, non-marring surface.
This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview
of the Table parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Assembly Steps
Overview
Leg (B)
Table Top (A)
FRONT FACING
Expansion Board of
Table Top (A)
3 ____
Step 3
Stand the Table up, with assistance from your adult partner.
Exert pressure floorwards, onto the Table with both your hands.
This pressure will help the Legs and Table Top reach full alignment status.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts in a sequential manner, until evenly secured.
When tightening the Bolts tighten sequentially.
Do not tighten any Bolt fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and excute the same above process.
If the Table is not Stable it could lead to damage to the product.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Place Table Top(A) facedown, onto a clean, non-marring surface.
Attach Leg(B) to Table Top(A) using Bolts(①), and Washers(②) with Allen Key(③).
Do not fully tighten the Bolt.
Repeat the same process with the remaining three Legs(B).
Step 2
4 ____
Unlock the Metal Fasteners.
Step 2
Step 1
With an adult partner, gently pull the Table Tops(A) outwards as indicated by the arrows above.
Caution: Do not Lean on or apply pressure to the Table Top when it is pulled open. This could
cause damage to the product.
Extention Steps:
To Extend the Table:
5 ____
3.1) Unfold the Expansion Board of Table Top(A), onto the Center of the Table as shown above.
3.2) Gently push the Table Top(A) inwards until the Top Table(A) fits into the Expansion Board of Table
Top(A).
Caution: Keep hands away from the Table Top(A) and Expansion Board of Table Top(A) when
pushing the Table Top to avoid pinching hazards.
If you can not push the Table Top(A) inwards, just lightly shake the Table Top(A).
Step 4
Step 3
Lock the Metal Fasteners under the Table Top to lock the Expansion Board of Table Top(A) into place
as shown in the above picture.
Your Table is extended and is now ready for use.
This Table can only be used on a flat, level surface.
3.1
3.2
6 ____
Step 1
Unlock the Metal Fasteners.
Step 2
2.1) With assistance from an adult, gently pull the Top Table(A) outwards as indicated by the arrows
above.
2.2) Fold the Expansion Board of Table Top, back inside of the Table Top as shown above.
Caution: Do not Lean on or apply pressure to the Table Top when it is pulled open. This could
cause damage to the product.
To Retract the Table:
2.1
2.2
7 ____
Step 3
Step 4
Push the Table Top(A) inwards until both wings of the Table Top(A) align.
Caution: Keep hands away from the Table Top(A) and Expansion Board of Table Top(A) when
pushing the Table Top to avoid pinching hazards.
If you can not push the Table Top(A) inwards, just lightly shake the Table Top(A).
Lock the Metal Fasteners under the Table Top(A) into place as shown in the above picture.
Your Table is retracted and is now ready for use.
This Table can only be used on a flat, level surface.
8 ____
9 ____
Loading...