Page 1
ASSEMBLY INSTRUCTIONS
Before you begin, please follow assembly instructions carefully, then follow them step by step.
Read instruction carefully . See Furniture Parts list and Hardware List for guidance . Be sure you have all parts before you start assembling .
Place and assemble furniture on a clean flat soft surface , such as carpet or rug to pervent being scratched .
PART LIST
TOP PANEL 1 PC
1
BOTTOM PANEL
2
SIDE PANEL (L)
3
SIDE PANEL (R)
4
CENTER PANEL (L)
5
CENTER PANEL (R)
6
CENTER PANEL
7
BONE PANEL
8
9
SHELF PANEL
BACK PANEL
10
DOOR PANEL (L)
11
DOOR PANEL (R)
12
LEG
13
SELF-PREPARED TOOLS: Tools below are NOT included in package.
SCREWDRIVER
HAMMER
QTY
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
1 PC
1 PC
1 PC
1 PC
4 PCS
HARDWARE
MINI FIX
A
M8 X 30MM WOOD DOWEL
B
M6 X 5OMM
C
CSK CAP WOOD SCREW
5/8 NAIL
D
ALLEN KEY M4
E
ONE HOLE L BRACKET (2MM)
F
M3.5 X 16MM C.B SCREW
G
SOFT CLOSING 7/8 HINGES
H
METAL SHELF SUPPORT
I
JCBC Screw M6 x 70
J
SPRING WASHER M6
K
FLAT WASHER M6
L
A1
A2
A3
10 PCS
28 PCS
10 PCS
31 PCS
1 PC
4 PCS
32 PCS
4 PCS
4 PCS
8 PCS
8 PCS
8 PCS
3
8
11
1
10
5
7
9
6
8
4
Reminder:
Please ensure that all surfaces and edges with colours/laminations are facing forward/outward.
12
2
13
Page 2
ASSEMBLY INSTRUCTIONS
STEP 1 STEP 2
- Insert hardware A2 onto panel (1).
(Repeat 10 times.)
- Assemble hardware
(Repeat 2 times on each panel.)
- Insert hardware
(Repeat 4 times on each panel.)
F to panel (8) with hardware G.
B onto panel (8).
B
SCREWDRIVER
REQUIRED
- Insert hardware A1 onto panel (3), (4), (5), (6) and (7).
(Repeat 2 times on each panel.)
- Insert hardware
(Repeat 4 times on each panel.)
x8
PRESS
A2
F
ROTATE
G
x4
8
x10
ROTATE
1
* Ensure the arrows on hardware
STEP 3 STEP 4
- Attach panel (8) to panel (3) and (5).
(Repeat 1 times.)
- Attach panel
(Repeat 1 times.)
(8) to panel (4) and (6).
8
3
- Attach panel (3), (4), (5), (6) and (7) to panel (1).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 10 times.)
PRESS
B onto panel (3), (4), (5), (6) and (7).
A1
x10
6
3
4
A1 point towards mounting positions.
B
x20
PRESS
7
5
SCREWDRIVER
REQUIRED
OR
HARDWARE
E
3
Section View
4
* In this step hardware
8
B are pre-inserted.
6
5
1
7
6
5
A2
ROTATE
A1
x10
A3
4
x10
* In this step hardware A1, A2 and B are pre-inserted.
PAGE: /4
2
PRESS
Page 3
ASSEMBLY INSTRUCTIONS
STEP 5 STEP 6
- Assemble hardware
by using hardware G.
- Assemble hardware F on panel (8) to panel (4) and (6)
by using hardware G.
(Repeat 1 times on each side panel.)
F on panel (8) to panel (3) and (5)
1
7
6
4
8
3
5
8
x4
G
ROTATE
SCREWDRIVER
REQUIRED
F
Connect panel (2) to panel (3), (4), (5), (6) and (7) by using hardware C and E.
(Repeat 10 times.)
* In this step hardware B are pre-inserted.
STEP 7 STEP 8
Assemble part 13 into panel (2) by using hardware E, J, K and L.
(Repeat 2 times for each Leg.)
Assemble panel (10) to entire body with hardware D.
(Repeat 31 times.)
3
5
1
6
4
7
2
C
x10
ROTATE
E
HAMMER
REQUIRED
E
3
5
1
7
K
J
ROTATE
L
x8
HIT
D
x31
10
13
6
4
2
13
PAGE: /4
3
2
4
Page 4
ASSEMBLY INSTRUCTIONS
STEP 9 STEP 10
Insert hardware I into mounting positions on panel (6) and (7) by hand.
(Repeat 4 times.)
1
Assemble the panel (9) into between panel (6) and (7).
(Repeat 1 times.)
3
7
5
2
6
4
I
x4
PRESS
* In this step hardware I are pre-inserted.
STEP 11 STEP 12
Fix hardware H onto panel (11) and (12) by using hardware G.
(Repeat 2 times for each hardware.)
H
G
SCREWDRIVER
REQUIRED
- Fix hardware H into panel (3) and (4) by using hardware G.
(Repeat 4 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel
(Do only when needed.)
H
x8
ROTATE
12
H
ADJUST
3
H
x16
ROTATE
5
G
1
7
9
2
11
6
(11) and (12).
3
5
2
4
SCREWDRIVER
REQUIRED
1
9
6
4
11
* In this step hardware H have been assembled in panel (11) and (12).
PAGE: /4
4
12
ADJUST
Loading...