ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJ ON CTEUR.
ASSEMBLING THE FIXTURE (Fig.2)
1. Carefully unpack new fixture and lay all the part s on a clear surface.
2. Return the arms to suitable position, see figure.2.
3. Attach the pipe thread(C) into the top coupling of the lamp body(D), lock it securely
4. Install the light bulbs(Not included) in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
HANGING THE FIXTURE (Fig.1 Please see the Page.2)
IMPORTANT: For a safe and secure installation, this fixture must be installed by
means of support that is independent of the junction box.
1. Shut off the power at the circuit breaker and remove old fixture from ceiling,
including the old crossbar.
2. Provide a 1/4” IPS pipe screw with one end securely mounted to a beam or a
structural member. The other end should protrude through the center of the junction
box as shown. The junction box is not included.
3. Assemble the hex nuts, lock washer, hex coupling, pipe screw and ceiling
loop(product shall prevail) to center 1/4”IPS support pipe and adjust overall length to
allow the lock ring to hold the canopy flush to the ceiling. When the adjustments
have been completed, secure the three (3) hex nuts, as shown.
4. Attach the chain to the fixture loop. Slip the lock ring and canopy over the upper end
of the chain. Open the open link of the chain and lift the fixture to att ach to the ceiling
loop and close the open link.
5. Lace the fixture wires, ground wire and safety cable through the chain and loop,
exiting through the side of the hex coupling.
6. IMPORT ANT: you must, run the safety cable through the two clamp bolts, then
through the top of the junction box and secure to structural member. NOW,
fasten the end of safety cable through the two clamp bolts(see fig.1), lock
them securely with the four small hex nuts until tight.
CONNECTING THE WIRES (Fig.3)
1. Take the black wire from the ceiling junction box and the smooth wire leg from the
fixture and twist bare ends together. Twist wire connector onto end of wire until
snug.
2. Repeat same process with white junction box wire and ribbed wire leg of fixture
wire. NOTE: Twist wires together in the same direction you twist the wire connector
onto wires.
with the hex nut. Attach the cover(B) onto the top coupling of the lamp body(D),
lock it securely with the loop(A). Slide the cover(G) and down flush to arms of the
lamp body(D), then slide the ring(F) and down flush to covers, tighten it with the
small screw, using the screwd river(E).
3. If your junction box has grounding wire (green or bare copper), attach this wire and
the bare copper wire from the fixture together as step 1.
4. Tuck these wire connections neatly into the ceiling junction box and then raise the
canopy all the way to the ceiling. Raise the lock ring to the bottom of canopy, screw
it with until tight.
Y our installation is now complete. Return power to the junction box and test the
fixture.
FIG.2
A
B
C
D
Canopy
F
G
E
Clamp
Bolt
F
G
E
Hex
F
G
FIG.3
Need assistance with parts or assembly? Please call customer service.
ALL RIGHTS RESERVED. Page 1 of 2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
Thank you for purchasing our product.
E
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or Bare
Copper(Ground)
Coupling
Loading...