Page 1
Label Picture Description QTY
A Table Top 1
B
Table Top Extension
Leaf
1
C
Inner Table Leg with
Pre-attached Leveller
2
D
Outer Table Leg with
Pre-attached Leveller
2
Assembly Instructions
Caution : You must read this before you proceed
Extension Table
CAUTION : This table is NOT a TOY.
Keep your child / children at bay in the process of assembly.
Page 1 OF 7
Page 2
Label Picture Description QTY
① Bolt(M6*22mm) 22
② Washer(6mm) 31
③ Spring Washer(6mm) 27
④ Bolt(M6*80mm) 3
⑤ Nut(6mm) 3
⑥ Spanner 2
Before
Beginn
ing
Assem
bly:
Page 2 OF 7
Page 3
Step 1
This table has multiple parts and may require up to 30 minutes to
assemble.
To give you an overview of the table parts, the above picture is to
help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with
the parts and steps before assembly.
Unpack and place all parts on a clean soft surface.
Overview
FRONT FACING
Table Top(A)
Table Top Extension Leaf
Inner Table Leg
with Pre
-
attached
Leveller(C)
Outer Table
Leg with Pre
-
attached
Leveller (D)
Page 3 OF 7
Page 4
Step 2
Step 3
Fix the Inner Table Leg with Pre-attached Leveller(C) and Outer
Table Leg with Pre-attached Leveller(D) with bolts(④), washers(②),
spring washers(③) and nuts(⑤) by spanner(⑥).
Do not over tighten.
Fix the bolts(①), washers(②), spring washers(③) to the unit by
spanner(⑥).
Do not over tighten.
Repeat the same assembly process for the other Inner Table Legwith
Pre-attached Leveller(C) and Outer Table Leg with PreattachedLeveller(D).
DO NOT fully tighten at this stage.
C
D
⑥
② ③ ⑤
②
④
② ③ ①
②③①
C
D
⑥
② ③ ⑤
②
④
② ③ ①
②③①
Page 4 OF 7
Page 5
Step 4
Step 5
Turn the table upside down on to a soft surface that does not scratch
the tabletop.
Attach Inner Table Leg with Pre-attached Leveller(C) and Outer
Table Leg with Pre-attached Leveller(D) to the mounting position on
the table top(A) with bolts(①), spring washers(③) and washers(②)
by spanner(⑥).
Do not over tighten.
Caution: you may need 2 adults to turn the table top A upside
down.
Turn the Table rightside up.
Adjust the pre-installed Leveller until the Table is level with the
ground.
Then, proceed to tighten all Bolts and Nuts.
Your table is ready for use.
Caution: This Table can only be used on a flat, level surface.
A(Table Top)
Table Leg
⑥
①
③
②
Adjust height
for balance
Adjust low
for balance
Page 5 OF 7
Page 6
Step6
Step 7
To shorten the Table, pull the table top apart, take Table Top
Extension Leaf(B) away, then towards the table top.
Your table is ready to use.
To expand the Table, pull the table top apart, place Table Top
Extension Leaf (B) into the middle leaf slot.
Adjust the direction/angle to tightly fit into the housing in the Table
Top.
B
B
Page 6 OF 7
Page 7
Page 7 OF 7
Loading...