Page 1
Assembly Instructions
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
EASY
DIFFICULT
Page 1 of 6
Tools Required for Assembly:
Allen Wrench
Wrench
Phillips Screwdriver
2 PERSONS RECOMMENDED
(Included)
(Included)
(Not Included)
Page 2
Page 2 of 6
Page 3
MD
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Parts List
#1 x 1 pc
Loveseat
#2 x 1 pc
Backrest
#3 x 1 pc
Left Armrest
#4 x 1 pc
Right Armrest
Hardware List
#A x 8 pcs
Threaded Stud
#B x 8 pcs
Bolt 5/16”x2-3/4”
#C x 16 pcs
Flat W asher
#D x 8 pcs
Hex Nut
#5 x 2 pcs
Pillow
#6 x 4 pcs
Leg
#7 x 1 pc
Leg Support
Due to the size and/or weight of this product, it is highly recommended that
the assembly should be done near the area of its intended location. Make
sure you have enough space to move around during the assembly.
ALWAYS have at least two people to help with transporting and
assembling of the product and to avoid any potential injury and/or damage.
#E x 1 pc
Wrench
#F x 1 pc
Allen Wrench
#G x 4 pcs
Screw
Page 3 of 6
Page 4
Insert 4 threaded studs (#A) into each of the left armrest (#3) and
the right armrest (#4).
Turn right (clockwise) to tighten
Note: Right and left are determined by
facing the front of the loveseat in the
upright position.
#A x 8 pcs
I. Insert the threaded studs (#A) assembled on the armrests into
the loveseat (#1).
II. Place 8 flat washers (#C) over the threaded studs (#A).
III. Secure 8 hex nuts (#D) onto the same threaded studs using the
wrench (#E) to tighten the parts together .
#C x 8 pcs
#D x 8 pcs
Turn right (clockwise) to tighten
Page 4 of 6
Page 5
Secure 4 screws (#G) into the bottom of the loveseat (#1)
using a Phillips screwdriver to tighten them down to the left
armrest (#3) and the right armrest (#4).
Turn right (clockwise) to tighten
#G x 4 pcs
Turn right (clockwise) to tighten
#B x 8 pcs
#C x 8 pcs
I. Align the 4 legs (#6) with
the corners of the loveseat
(#1).
II. Prepare 8 bolt assemblies
by inserting the flat washer
(#C) onto the bolt (#B).
III. Insert the bolt assemblies
through the loveseat (#1)
and secure those bolts
using the Allen wrench (#F)
to lock them with the legs
(#6).
IV. Align the threaded end of
the support leg (#7) with the
pre-drilled hole of the
loveseat (#1) and tighten by
hand until secured.
Page 5 of 6
Page 6
Assemble the backrest (#2) with the left armrest (#3) and the
right armrest (#4) by aligning the brackets of the backrest (#2)
with the brackets of the armrests. Slide the brackets together
until locked. Make sure all parts are firmly secured.
Place the 2 pillows (#5) onto the loveseat. Make sure the
loveseat is rested on a flat surface and does not feel loose or
wobbly. If it does, double check that the bolts/screws are secured
and properly tightened.
ASSEMBLY IS COMPLETED
Page 6 of 6
Loading...