GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK
WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this
fixture.
STEP 1: Thread pipe(Q) into connector(R), pipe(P) into pipe(Q),
pipe (O) into pipe (P), pipe (N) into pipe (O), pipe (M)
into pipe (N), and thread coupling (K) into pipe (M).You
can also selected the pipes for your desired height.
STEP 2: Attached the glass (W) to the frame (N) and secure
with adjustable glass holders (X)
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Drilling four holes into the Ceiling ,and strike the four
red plastic screws(A) into the holes.
STEP 2:Thread the safety steel cord(I) all the way through the
pipes, coupling(K),coupling(K),canopy(J) and one hole
of stopper(G) to the holes of mounting bar(C) and pull
it out from another hole of the mounting bar(C) to the
another hole of the stopper, then fasten it with two
screws(F) to the stopper(G) .
STEP3:Thread mounting screws(D) into the mounting
bar(B).Secure the mounting bar(B) to outlet box with
screws(D)
STEP 4: Attach screws (H) to the red plastic screws (A) through
the mounting bar (B)
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw(E) into the hole with
two raised dimples on the round mounting bar(B).
Wrap the ground wire from the fixture (if supplied)
around the green grounding screw, then connect it to
ground wire from the outlet box (if not fixed on the
outlet box) using a wire connector (not supplied). If
ground wire from the fixture is not supplied, wrap the
ground wire (if not fixed on the outlet box) from the
outlet box around the green grounding screw (E) and
tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below:
twist wires together before using wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and
screw the connector clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4 as
above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner. Make sure no
bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside
outlet box. Raise canopy(J) allowing for the mounting
screws(C) to protrude through the hole on
canopy(J).then secure with ball nuts(L).
STEP 2:Attached the glass (W) to front side of the frame (S)
and secure them with adjustable glass holders (x)
STEP 3: Attached the candle covers(U) to the sockets(V) and
install Bulbs(T) (Bulbs are not included, Please do
not exceed the maximum capacity with is
recommended on the candle cover (U).
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to
order replacement parts. Be sure to use exact wording from
illustration when ordering parts.
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round
in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
Loading...