White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
INSTALLATIONINSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING THE FIXTURE ( Fig. 2)
1. Carefully unpack new fixture and lay all the parts on a clear
surface.
2. Attach the center tube (K) to the fixture body (D), and then attach
the tube (K) to the center tube (G) by turning it clockwise until
tight.
3. Attach the center tube (G) to the columm (A) by turning it
clockwise until tight.
4. Clip the center ring (I) of the cloth shade (E) onto the center tube
part (H) of the fixture body (D), and then turn the screw (J)
clockwise to tighten the cloth shade (E).
5. Hook the arm (B) to the hook on the columm(A) and the frame(F)
6 ． Place the socket sleeve (C) over the socket.
HANGSSING THE FIXTURE ( Fig. 1 )
1. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old crossbar.
2. Thread nipple (C) into loop (F) until snug.
3. Thread other end of nipple (C) with loop attached into crossbar
(D) until snug.
4. Place lock washer (B) over end of nipple protruding t hrough
crossbar and thread hex nut (A) onto nipple until tight.
5. Take this crossbar assembly and mount to ceiling junction box
with junction box screws (E). Tighten screws securely with
screwdriver .
6. Us ing proper chain pliers to open one end link of the chain
provided and connect to the fixture loop (I). Close the link . Lace
the fixture wires through the chain.
7. Lace the fixture wires through the chain.
8. By measuring, determine correct number of links needed for
proper hanging height. Using proper chain pliers disconnect and
discard remaining chain.
9. Slip loop collar (H) over the chain, then do the same with the
canopy (G).
10. Open the other end link of the chain and hang the f ixture on the
loop at the ceiling. Close the link.
11. Feed the fixture wires through the loop (F) and nipple (C) and
pull until taut.
Install
Install
12. Install
Install the
specifications.
specifications.
specifications.
specifications. DO
WATTAGE
WATTAGE
WATTAGE
WATTAGE RATING!
the
light
the
light
the light
light bulbs
RATING!
RATING!
RATING!
bulbs
bulbs
bulbs in
DO
NOT
DO
NOT
DO NOT
NOT EXCEED
in
accordance
in
accordance
in accordance
accordance with
EXCEED
EXCEED
EXCEED THE
with
the
with
with the
THE
THE
THE MAXIMUM
fixture
the
fixture
the fixture
fixture
MAXIMUM
MAXIMUM
MAXIMUM
CONNECTING THE WIRES ( Fig. 3)
1. Take the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed
wire leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together
as step 1.If junction box has no ground wire, attach the bare
copper fixture wire to the green ground screw on the crossbar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy (G) all the way to the ceiling. Raise the loop
(H) and thread onto ceiling loop protruding through canopy
Your
Your
Your
Your
box
box
box
box and
installation
installation
installation
installation is
and
test
and
test
and test
test the
is
now
is
now
is now
now complete.
the
fixture.
the
fixture.
the fixture.
fixture.
complete.
complete.
complete. Return
Return
Return
Return power
power
power
power to
to
the
to
the
to the
the junction
junction
junction
junction
Fig. 1
Fig. 2
’
s
’
s
’
’
s
s
Fig. 3
Loading...