INSTALLATION INSTRUCTION
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en posi
tion d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.
HARDWARE
A1 B1 C1
Wire
Connector
Qty: 3
Junction Box
Screw
Qty: 2 + 1 extra
Mounting
Screw
Qty: 2 + 1 extra
INSTALLATION INSTRUCTION
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture,
including the mounting hardware.
2. Carefully unpack your new xture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Place the glass (E1) onto the holder (H1).
4. Adjust the xture wire length by pressing the cable-trippers (I1) on
canopy and pulling the wire. Make sure the wires are the same length.
5. Re-set the strain relief (J1) near the wiring holes.
Cut the xture wires and leave at least 6”.
Note: The xture wires have two braided layers.
Strip the two layers carefully!
CONNECTING THE WIRES (Fig. 2)
6. Connect the driver input wires with Junction box as shown in Fig. 2,
making sure that all wire connectors (A1) are secured.
Tuck wires carefully inside junction box (F1)
7. Mount the driver onto the mounting plate (D1) using the
provided double sided adhesive tape. Feed driver output wires
through mounting plate holes. Fasten the mounting plate (D1)
to the junction box (F1) using junction box screws (B1).
The side of the mounting plate marked “GND” must face out.
FIG.1
Junction box
wire
Driver
Fixture wire
Junction box
F1
Wire connectors
A1
Mounting plate
D1
Junction box screw
B1
J1
Strain relief
C1
G1
I1
Cable-trippers
Screws
Canopy
*Requires Driver to be recessed within the junction box.
8. Connect the driver output wires with the xture wires, red (+) to red
(+) and black (-) to black (-) making sure that all wire connectors are
secured. Fixture and junction box ground wires should be connected
to mounting plate using green screw provided.
9. Place the canopy (G1) over the mounting plate (D1),
secure with screws (C1).
10. Check to ensure xture is level and adjust cables if necessary.
FIG.2
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare Copper
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
H1
E1
Glass
Glass holder
Loading...