Assembly Instructions
02 persons may be needed to execute this action.
Caution: You must read this before you proceed
CHAIR
Caution: This Chair is NOT a TOY.
Keep your child / children at bay in the process of assembly.
For turning the Chair and to prevent damage to the Chair,
Page 1 of 9
Parts List
Label Picture Description QTY
Backrest
A
B
C
D
Panel 1
Seat Panel
1
Left Leg
Panel 1
Right Leg
Panel 1
E Rocking base 2
F
G
H Seat Cushion 1
Left Leg
1
Support Bar
Right Leg
1
Support Bar
Page 2 of 9
①
②
③
④
⑤
⑥
Hardware
Assembly Preparation
Note: A Long Bolt (②) will be used to guide in the Cross Nut (⑤)
This Bolt is to be kept with Allen Key as spare Hardware
Label Picture Description QTY
Before Beginning Assembly:
Screw (M6*80mm)
Long Bolt
(M6*70mm)
Short Bolt
(M6*35mm)
Sleeve Nut
(M6x15mm)
Cross Nut
(M6x13mm)
Allen Key
7
7
3
3
7
2
Page 3 of 9
Assembly Steps
Overview
Right Leg
Panel (D)
Backrest
Panel (A)
Left Leg
Panel(C)
Left Leg
Support Bar(F)
Right Leg
Support Bar(G)
This Chair has multiple parts and may require up to 30 minutes to assemble. To give you
an overview of the Chair parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the
parts and steps before assembly.
FRONT FACING
Seat
Cushion (H)
Seat Panel
(B)
Rocking
base(E)
Step 1
Unpack and place all parts on a clean, non-marring surface.
Page 4 of 9
Step 2
Position Right Leg Panel (D) to Rocking Base (E)
) by hand,turning clockwise.
) through the housing position of Rocking Base (E) and affix
)
D
E
2
2.2
2.1.1
5
2
2
6
2.1.2
2.1.1) Attach Long Bolt (②) to the top of Cross Nut(⑤
Insert both into housing position of Right Leg Panel( D)
2.1.2) Insert the Long Bolt (②
to Cross Nut (⑤) inside of Right Leg Panel( D), tighten with Allen Key(⑥
2.2) Remove the first Long Bolt (②) by hand
Do not fully tighten the Bolts.
Page 5 of 9
Step 3
D
E
G
6
3.1.1
2
3.2
2
5
3.1.2
2
4
6
3
6
Position Right Leg Support Bar (G) to Rocking Base (E) and Right Leg Panel (D)
3.1.1) Attach Long Bolt (②) to the top of Cross Nut(⑤) by hand, turning clockwise. Insert
both into housing position of Right Leg Support Bar (G)
3.1.2) Insert the Long Bolt (②) through the housing position of Rocking Base (E) and affix
to Cross Nut (⑤) inside of Right Leg Support Bar (G), tighten with Allen Key(⑥)
3.2) Remove the first Long Bolt (②) by hand
3.3) Secure Right Leg Support Bar (G) to Right Leg Panel (D) by using Short Bolt (③),
Sleeve Nut (④) and Allen Key (⑥)
Do not fully tighten the Bolt.
3.3
Repeat the same process of Step 2 and 3 for the other Left Leg Panel (C) and Left Leg
Support Bar (F)
Page 6 of 9
Position the Seat Panel (B) to Left Leg Panel (C) as shown.
).
Do not fully tighten the Screws.
Leg Panel (C) to Seat Panel (B) in same process above.
Step 4
B
C
D
B
A
C
D
6
1
4.1
4.1) Place the Left Leg in Step 3 with inside face skywards onto a clean, soft surface to
avoid any scratches or damages to the product
4.2) Attached Right Leg Panel (D) in Step 3 into Seat Panel (B), secure by using Screw
(①) and Allen Key (⑥
With assistance from your adult partners, turn the Chair to the other side and secure Left
4.2
Step 5
1
6
With assistance from your adult partners, turn the Chair right side up
Attach Backrest Panel (A) to Right Leg Panel (D) and Left Leg Panel (C ), secure by using
Screw (①) and Allen Key (⑥)
Do not fully tighten the Screws.
Page 7 of 9
Step 6
H
Inspect the Chair and make sure all parts are adequately connected.
In a sequential manner, tighten all Bolts and Screws at all joints.
Place Seat Cushion (H) on to the Chair using the velcro straps as shown above.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
Page 8 of 9
Page 9 of 9
Loading...