Assembly Instruction Sheet
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wirestrippers, electricaltape,safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifany partsaremissing ordamaged,do notattemptto assemble,install,or operatethefixture. Contactcustomerservice forreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A21 MediumBase150W Maximum.
30-45minutes
Identifyandinspect allpartsbefore beginninginstallation.Check packagecontentlist anddiagramsbelow tobesure allpartsare
Package Contents
Fixture
Loop
A
x1
Fixture
B
Body
x1
Hardware Contents
Lock
Washer
BB
x2
Crossbar
AA
x1
Hex Nut
CC
x2
Nipple
DD
x1
STEP 1 Install Fixture Loop,
Fixture Body and Cage together
A. Threading Fixture Loop (A) onto
C. Pass the top edge of the Cage
STEP 2 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
-
Fixture Body (B), hand tighten
until sung.
(C) over the bolts on the bottom
edge of the fixture hood of the
Fixture Body (B) and secure with
Lock Balls (D). Hand tighten until
sung.
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Green Ground
Screw
EE
HH
Outlet Box
AA
Outlet Box Screw
(not included)
Cage
C
x1
Canopy
Chain Loop
x1
Canopy Lock
FF
Ring
x1
Fixture Chain
GG
x1
Quick Link
x2
Ceiling Canopy
II
x1
A
Lock Ball
D
x2
B
D
C
Figure 1
Figure 2
STEP 3 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place
another Lock Washer (BB) over the Nipple (DD) and then thread the
Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about
0.375” above the Crossbar (AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (II) over the
Canopy Chain Loop (EE)
against the ceiling to
determine the correct position
of the Nipple (DD). Thread the
Canopy Lock Ring onto the
Canopy Chain Loop (EE).
Adjust the Nipple (DD) to
allow the Ceiling Canopy (II)
to rest against the ceiling
when held in place by the
Canopy Lock Ring (FF).
D. Remove the Canopy Lock
Ring (FF) and the Ceiling
Canopy (II). Tighten the Hex
Nut (CC) against the Crossbar
(AA) to secure in place.
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
links if needed.
*
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop and the
Canopy Chain Loop (EE), pull the supply wires through the Fixture
Chain (GG) alternating links. After the wires are through the Fixture
Chain (GG), pull the Supply Wires and the Ground Wire through the
Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with
one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up and
attach the other end of the Fixture Chain (GG) onto the Canopy
Chain Loop (EE) with another Quick Link (HH). The fixture will now
hang safely. Close the chain loop at the Ceiling Canopy Loop (EE).
D. Feed the Supply Wires and Ground Wire through the Canopy Chain
Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving
Approximately 8” of wire extending from the Outlet Box.
E. Refer to Step 5 for wire connections.
F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the
AA
BB
DD
CC
EE
FF
CC
BB
Step B
Step A
II
Figure 3
1of2
Fixture Chain (GG) and over the
Canopy Chain Loop (EE). Tighten
the Canopy Lock Ring (FF) onto
the Canopy Chain Loop (EE) until
tight.
Suggested chain length for
Ceiling height :
8’ ceiling : use 15 links of chain
and 2 quick links
9’ ceiling : use 25 links of chain
and 2 quick links
10’ ceiling : use 35 links of chain
and 2 quick links
Supply
Wires and
Ground Wire
GG
Figure 4
DD
HH
FF
HH
A
EE
How to Replace Glass Shade
Fixture
A. Unlock Lock Balls and
remove Fixture Hood
the Cage
B Unscrew Flat Head Screws
.
.
from
Bolt
Hood
Flat Head
Screw
on the Cage with Glass
Shade, remove Tabs and
Glass Shade from the Cage.
C. Replace the
Glass Shade
with a new one and re
verse
Tab
above steps to reinstall
iously removed parts
prev
back onto fixture.
II
Glass
Shade
Lock Ball
Figure 7
Cage
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Ribbed side of wire from fixture
identified with the Label “N”
Smooth side of wire from fixture
identified with the label “L”
Ground wire
from fixture
Figure 5
STEP 6 - Install Bulbs
A. Insert bulbs into sockets and
screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
FINISH: EARTH BLACK
4.5”Sq.
1”
120” OVERALL
HEIGHT INCLUDES
96” CHAINS AND
(2) QUICK LINKS
18.75”
13.5”
7.25”
10.5”
Figure 6
Socket
Bulb (not
supplied)
7.25”
10.5”
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
2of2
Loading...