INSTALLATION INSTRUCTIONS
OUS
OUS
OUS
A
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture, including the mounting
hardware.
2. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
3. Attach the nipple (J) by screwing in coupling (O) on the fixture
body (T).
4. Secure one side of metal bars (L) to the housing (K) by using
short screws (M), secure the other side of metal bars (L) to
fixture body (T) by using long screws (N).
5. Align cloth shade (W) with screw (P) by cap nut (X).
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 2)
6. Determine the desired hanging height and thread rods (F1, F2
and F3) to the nipple (I) of the fixture body (J). Then attach
loop (H1) by screwing in to rod (F1). Note: remove the nipple if
installing with one 6” rod only.
7. Attach the quick link (G) connect to loop (H1) and loop (H2) on
the canopy (D), carefully feed the wire over loop (H1), quick
link (G) and loop (H2).
8. Thread screws (A) into the pre-drilled holes in the circular
strap (B) spaced the same distance apart as the holes in the
canopy (D).
9. Attach the circular strap (B) to the Junction box using
mounting screws (C) (Size: #8-32N*L0.5”). The side of the
circular strap marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
10. At this point, connect the electrical wires as shown in figure 3,
making sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap using the green screw provided.
11. Tuck the wir e connectors neatly into the ceiling Junction Box
and then raise the canopy all the way to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
12. Thread screws (A) into canopy (D), and secure with knurled
knobs (E).
13. Install light bulb(s) (not included) in accordance with the
fixture’s specification. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
14. Thread the nipple (U) to socket assembly (R) and tighten it
with hex nut (S).
15. Align spacer (V) followed by glass shield (Y) onto nipple (U),
adjust spacer (V) to make glass (Y) flat with cloth shade (W)
and secure with finial (Z).
Your installation is now complete. Return power to the junction
box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
Fig. 1
Fig. 3
FIXTURE
WIRES
Black or
Smooth
B
C
H2
F1
D
E
G
H1
-Circular Strap
-Ground screw
-Mounting Screw*2
F2
H3
J
T
R
U
E
H
WIRES
Black
(Hot)
I
K
M
L
O
S
V
Z
FIXTURE
WIRES
White or
Ribbed
Rod 1(F1)
2(F2)
1(F3)
N
P
W
X
Y
FIXTURE
WIRES
Bare
Copper
(Ground)
E
H
WIRES
White
(Neutral)
H
WIRES
Green
(Ground)
E
Page: 1/2
Fig.2
a. Hardware Bag:
A. Screw*2
B. Circular Strap*1
D. Canopy *1
H2
F1
A
B
C
D
E
G
H1
C. Mounting Screw*2
E. Knurled Knob*2
H. Loop*2
G. Quick Link*1
b. Hardware Bag:
F1. ROD 12"*1
F2. ROD 12"*2
F3. ROD 6"*1
Page: 2/2
B
F1
D
F2
C
F3
A
E
G H
Loading...