standard Bed assembly
upholstered side rails hardware
You will need:
• phillips screwdriver
• at head screwdriver
(6) 1¼” washers(6) 1” x 5/16” bolts
bed components
• pliers
*Open all hardware
packets in both packages
before starting assembly.
Wingbacks come with two
additonal bolts/washers
which are listed in the
chart in Step 5.
(4) legs
for all sizes
(6) King/California King
(4) corner brackets
for all sizes
support legs
(1) Twin
(2) Full
(3) Queen
(1) upholstered foot rail
for all sizes
(2) side rails
for all sizes
support rails
(1) Twin/ Full/ Queen
(3) King/California King
(2) end rails
for all sizes
(2) upholstered side rails
for all sizes
bed hardware
1” x ¼” bolts
(1) Twin
(2) Full
(3) Queen
(6) King/California King
(4) ¾” washer
(larger center)
for all sizes
(1) wrench
for all sizes
(4) ¾” x 5/16” bolts
for all sizes
¼” nuts
(10) Twin/ Full/ Queen
(14) King/California King
(1) 5/32” L wrench
for all sizes
¼” bolts
(10) Twin/ Full/ Queen
(14) King/California King
(8) ¾” screws
for all sizes
(1) 3/16” L wrench
for all sizes
¾” washer
(smaller center)
(1) Twin
(2) Full
(3) Queen
(6) King/California King
(2) L Brackets
for all sizes
If you have any questions, please call us
limited warranty
We guarantee our upholstered furniture against defects in construction for a period of one (1) year. When a structural defect is brought to
our attention, we will repair or replace it at our option at no charge to the customer (includes parts and labor, not transportation costs).
Fabric wear-ability for upholstered furniture is not covered by the warranty. Vacuum for regular cleaning.
PLEASE DISPOSE OF PLASTIC BAG(S) AND CARTON(S) RESPONSIBLY.
Step 1
1. Attach side rail and end
rail to corner bracket.
Make sure to align holes
and snap into thinner slot.
Continue this action until
you have a rectangular
frame.
1
2. Attach corners to rails using
(8) ¼” bolts and (8) ¼” nuts.
2
3. Attach legs to rails using
(4) ¾” x 5/16” bolts and
(4) ¾” washers.
3
Step 2
(Queen bed frame image displayed)
2
1. Attach each support bar using
(2) ¼” bolts and (2) ¼” nuts.
Make sure to attach the support
bar underneath the bed frame.
Note:
Twin/ Full/ Queen = 1 support bar
1
King/California King = 3 support bars
2. Attach each support leg to the
bar using (1) 1” x ¼” bolts and
(1) ¾” washer.
Note:
Twin = 1 support leg
Full = 2 support legs
Queen = 3 support legs
King/California King = 6 support legs.
(2 legs for each support bar)
Step 3
1. Use (6) 1” x 5/16” bolts,
(6) 1 ¼” washers to attach rails
to bed frame loosely. Screw in
side rails before attaching the
foot rail.
2. Push side rails towards foot
rail, so that there is no gap.
Step 4
Step 5
(Queen bed frame image displayed)
Connect assembled bed frame
and rails to your headboard.
Attach pieces using (4) 1” x ¼”
bolts, (8) 1¼” washers*, and
(4) ¼” nuts. Proceed to Step 5
for Wingback beds, otherwise
continue onto Step 6.
* Use a washer on each side of the metal
legs when attaching headboard to the
bed frame.
(Queen bed frame image displayed)
Only for Wingback beds:
Refer to chart to use assigned
bolts and (2) 1 ¼” washers for
the top hole (see image). Bolts
are enclosed with headboard
hardware. You might have to
loosen the bolt/washer below it to
align both holes properly.
Wingback Side Rail Bolt Chart
Bolt Size
2” x 5/16”
2½” x 5/16”
3” x 5/16”
No bolt needed
Step 6
With a phillips screwdriver,
attach (2) L brackets and
(8) ¾” self-tapping screws in
the corners of the foot rail. This
is needed to increase stability of
upholstered rails.
Loading...