INSTALLATION INSTRUCTIONS
R E A D I M P O RTA NT S AFETY T IPS BEFORE P ROCEEDING WITH I NSTA LL AT I O N
INSTALLATION INSTRUCTIONS
R E A D I M P O RTA NT S AFETY T IPS BEFORE P ROCEEDING WITH I NSTA LL AT I O N
SAFETY TIPS
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
outlet box
1 2
fixture
mounting
screws
mounting screw
ATTACH small cross bar to outlet box with outlet box screws
(8-32 x 1/2, screws not provided). THREAD fixture mounting
screws (8-32 x 1,2 provided) into large cross bar. ATTACH
large cross bar to small cross bar with mounting screw (1/4
- 20 x 3/8,1 provided).
screws
(not provided)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
ground
wire
large cross bar
outlet
box
small cross barouter cross bar
CONNECT THE WIRES. NOTE: Attach black fixture wire to black
supply wire, white fixture wire to white supply wire. Do not mix
them up. Use approved electrical tape or wire connectors (not
provided). Connect bare fixture ground wire to ground wire
from outlet box. NEVER CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
43
thumb nuts
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
ground wire
wire
connectors
(not provided)
caulkmounting screws
SAFETY TIPS
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
outlet box
1 2
fixture
mounting
screws
mounting screw
ATTACH small cross bar to outlet box with outlet box screws
(8-32 x 1/2, screws not provided). THREAD fixture mounting
screws (8-32 x 1,2 provided) into large cross bar. ATTACH
large cross bar to small cross bar with mounting screw (1/4
- 20 x 3/8,1 provided).
screws
(not provided)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
ground
wire
large cross bar
outlet
box
small cross barouter cross bar
CONNECT THE WIRES. NOTE: Attach black fixture wire to black
supply wire, white fixture wire to white supply wire. Do not mix
them up. Use approved electrical tape or wire connectors (not
provided). Connect bare fixture ground wire to ground wire
from outlet box. NEVER CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
43
thumb nuts
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
ground wire
wire
connectors
(not provided)
caulkmounting screws
fixture mounting
screws
POSITION THE FIXTURE over large cross bar and secure
in place with thumb nuts (2 provided). Insert compact type
lamps rated 9 watts into sockets. Be sure to use compact type
lamps with wattage no greater than specified for this fixture.
COLD WEATHER STARTING INFORMATION: For temperatures below 25°F leave the PL9 lamp(s) on continuously - starting with
warm lamps. NOTE: If lamp starting becomes a problem in any cold weather applications; remove the lamp(s) from fixture bring the lamp(s) indoors so that they become warm - then re-install the lamp(s) into fixture and leave fixture on continuously.
Do not place lamp(s) in an oven, microwave or similar heat producing device.
NOTE: Be sure wires exiting the back of fixture are not pinched
between the back of fixture and ceiling or wall.
CORRECT
Wires MUST lay in this slot
INCORRECT
PLACE DIFFUSER ON FIXTURE BASE. Then place bar grill or
frame over diffuser and attach to base with mounting screws
(8-32 x 1/2, 4 combination head screws provided). NOTE:
Outdoor wall fixture MUST be caulked with an acrylic caulk
where base of fixture meets mounting surface. This provides
a water tight seal when fixture is installed.
NOTE: Following warning applies to ceiling installation only.
WARNING - RISK OF FIRE, MOST DWELLINGS BUILT
BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚C. CONSULT A
QUALIFIED ELECTRICIAN BEFORE INSTALLING. FOR SUPPLY
CONNECTIONS, USE WIRE RATED FOR AT LEAST 90˚C.
Clean only with mild soap and water. Avoid spraying
with Cleansers, Insecticides, and Pesticides that are
petroleum based hydrocarbon products. These will
degrade luminaire.
diffuserbar grill
base
IS010PL Rev B
fixture mounting
screws
POSITION THE FIXTURE over large cross bar and secure
in place with thumb nuts (2 provided). Insert compact type
lamps rated 9 watts into sockets. Be sure to use compact type
lamps with wattage no greater than specified for this fixture.
COLD WEATHER STARTING INFORMATION: For temperatures below 25°F leave the PL9 lamp(s) on continuously - starting with
warm lamps. NOTE: If lamp starting becomes a problem in any cold weather applications; remove the lamp(s) from fixture bring the lamp(s) indoors so that they become warm - then re-install the lamp(s) into fixture and leave fixture on continuously.
Do not place lamp(s) in an oven, microwave or similar heat producing device.
NOTE: Be sure wires exiting the back of fixture are not pinched
between the back of fixture and ceiling or wall.
CORRECT
Wires MUST lay in this slot
INCORRECT
PLACE DIFFUSER ON FIXTURE BASE. Then place bar grill or
frame over diffuser and attach to base with mounting screws
(8-32 x 1/2, 4 combination head screws provided). NOTE:
Outdoor wall fixture MUST be caulked with an acrylic caulk
where base of fixture meets mounting surface. This provides
a water tight seal when fixture is installed.
NOTE: Following warning applies to ceiling installation only.
WARNING - RISK OF FIRE, MOST DWELLINGS BUILT
BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚C. CONSULT A
QUALIFIED ELECTRICIAN BEFORE INSTALLING. FOR SUPPLY
CONNECTIONS, USE WIRE RATED FOR AT LEAST 90˚C.
Clean only with mild soap and water. Avoid spraying
with Cleansers, Insecticides, and Pesticides that are
petroleum based hydrocarbon products. These will
degrade luminaire.
diffuserbar grill
base
Loading...