MTMH13HYDB.1
Model: TMH13HYD
Iron
&
Oak 20 To
n
Tractor Mount
Horizontal Log
Model TMH13HYD
Splitter
Owner / Opera
and Safety Manual
tor
800-817-1005
1
Iron & Oak
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Personal Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Worksite Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Log Splitting Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Shipping List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attaching Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Assembly and Initial Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Start-Up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications
Troubleshooting
Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Warranty Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Optional Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NOTE: Iron and Oak Commercial Products reserves the right to make technical
changes for product improvement. This manual may contain illustrations
and photographs, for demonstration purposes, which slightly deviate from the
actual product design.
Serial Number
Date of Purchase
Please enter the serial number and purchase
date of your log splitter in the space provided.
Keep this manual for future reference.
Iron & Oak
2
800-817-1005
WARNING
To avoid personal injury or death, carefully read and understand all
instructions pertaining to the Iron & Oak Commercial Products’ log
splitter.
Do not attempt to assemble, operate, or maintain our product without
fully understanding all our instructions and safety precautions. Do
not operate the log splitter unless you read and understand the
instructions and warnings in this manual. If any doubt or question
arises about the correct or safe method of performing anything found
in this or other Iron & Oak Commercial Products’ manuals, contact
your Iron & Oak Commercial Products’ dealer or call the Sales and
Service representatives at our main headquarters. Proper care is
your responsibility.
WARNING
Accidents can often be avoided by being alert and recognizing potentially
hazardous situations. Any individuals operating, maintaining, or repairing
products manufactured by Iron & Oak Commercial Products should have the
necessary training, skills, and tools required to perform these functions
properly and safely. The safety information in this manual serves as a basic
guide in an attempt to prevent injury or death.
Iron & Oak Commercial Products cannot anticipate every possible
circumstance that might involve a potential hazard. The warnings in this
manual and on the product itself are, therefore, not all inclusive. If tools,
procedures, work methods, or operating techniques that are not specifically
mentioned by Iron & Oak Commercial Products are used, you must satisfy
yourself that they are safe for you and for others. Make sure the log splitter will
not be damaged or made unsafe by any operation, lubrication, maintenance,
or repair procedures that you choose.
DO NOT proceed if any doubt arises about the correct or safe method of
performing anything found in this or other Iron & Oak Commercial Products’
manuals. Seek out expert assistance from a qualified person before
continuing.
800-817-1005
5
Iron & Oak
Introduction
The commercial THM13HD Horizontal Tractor Mount Log Splitter is designed for tough
applications elevated or on the ground. With up to 20 tons of splitting force, the
THM13HD will handle most of your commercial log splitting needs. The log splitter
attaches to any tractor with a class 1, 2, or 3 three-point hitch.
Power for the THM13HD comes directly from tractor-supplied hydraulic pressure. The
maximum splitting force is determined by the pressure output of the tractor’s hydraulic
sys- tem. For example, 3000 psi of pressure produces 20 tons of splitting force, 2000 psi
produces 12.5 tons, and 1500 psi produces 9 tons.
An attractive, powder-coated finish provides the finest protection available and Iron &
Oak’s rigid, quality-control and component testing help ensure years of productive, reliable service. Since 1982, the name Iron & Oak has stood for quality and reliability when
it comes to log splitters and wood processing products.
Iron & Oak Commercial Products offers the finest commercial log splitter on the market
today!
✔ Rugged, heavy-duty construction for years of exceptional service.
✔
Fits category 1, 2, and 3 tractor hitches.
✔ Rigid, quality-control during manufacturing ensures greater reliability.
✔ Factory testing of all major components.
✔ Powder-coated finish for the best appearance and weather protection.
✔ Year-round manufacturing, parts, and support.
For additional information, contact us at:
Iron & Oak Commercial Products
20195 S. Diamond Lake Rd., STE 100
Rogers, MN 55374
Phone: (800) 817-1005 (toll free)
Fax: (866) 779-9963
E-mail: sales@ironandoak.com
Web Site: www.ironandoak.com
Safety
The following is a list of safety rules you must follow in order to use your log
splitter safely.
Personal Protection
✔ To avoid personal injury or death, carefully read and understand all
instructions pertaining to the log splitter including the engine manufacturer’s
operating and maintenance instruction manual.
Iron & Oak
4
800-817-1005
✔ Always wear protective gear, such as safety
goggles, tight-fitting gloves without drawstrings or loose cuffs, steel-toed shoes, and a
protective hearing device.
✔ To prevent injury, make sure all decals are attached to the log splitter and
AR
N
I
are legible at all
times.
Worksite Safety
✔ To avoid tripping, do not leave tools, logs, or other components laying around
in the work area.
✘
NEVER operate your log splitter on slippery, wet, muddy, or icy surfaces. The
location you choose should be flat, dry, and free from any tall grass, brush,
or other interferences.
✘
NEVER operate the tractor in an enclosed area. Exhaust fumes contain car-
bon monoxide which can be deadly when inhaled. Make sure the area is well
ventilated.
✘
NEVER use your log splitter at night.
✘
NEVER leave the log splitter running unattended
going to be away from the log splitter even for a short period of time.
✘
NEVER attempt to move your log splitter over hilly or uneven terrain without a
tow vehicle.
. Shut off engine if you are
✔ ALWAYS operate your log splitter on dry, solid, level ground.
✔ ALWAYS engage the parking brake and block the wheels of the tractor to
prevent movement while operating the log splitter.
✔ Sudden movement or accidental starting of the tractor can cause personal
injury or death to persons on or near the tractor. When working on or near
the tractor, park the tractor on a smooth level surface, stop the engine, and
engage the parking brake.
800-817-1005
5
Iron & Oak
Operating Safety
✔ ALLOW ONLY ONE (1) PERSON TO LOAD AND OPERATE THE LOG
SPLITTER.
✔ Allow only adults to operate the log splitter. No one under the age of 18 should
be allowed to operate the log splitter.
✔ Always keep bystanders, including children and pets, at least twenty-five (25)
feet away from the work area. Only the operator should stand near the
equipment, and the operator should stand only within the safe operating zone
pre- scribed in this manual (see the photos on safe and unsafe operating
zones in the “Operation” section).
✔ When the ram of the log splitter is in the return mode, keep your hands off the
machine — the log splitter is designed to automatically stop when the cylinder
is fully retracted.
✔ Personal injury or death can result from not engaging the tractor’s parking
brake while attaching the log splitter. If the parking brake is not engaged, the
tractor may roll while you are on or near the tractor. Always engage the
parking brake before leaving the tractor.
✔ Personal injury could result from an improperly coupled log splitter. Be certain
draft links, top link, and hitch pins are fully engaged on both sides before using
the log splitter.
✔ An improperly installed log splitter could become dislodged from the tractor
during operation. This could cause injury or death. Do not operate the tractor
until you are sure the log splitter attachment is properly connected.
✔ Heavy three-point hitch mounted equipment reduces road stability, regardless
of the amount of front-end counterweight added. Insufficient roading stability
can lead to an accident, causing personal injury and property damage. Reduce
speed when encountering rough terrain or whenever the tractor’s directional
stability is reduced.
✘
Do not allow any person to operate the log splitter until they have read and
understood the safe operating instructions contained in this manual.
✘
Machine instability can result in injury or death. To ensure stability during
operation, do not overload the tractor and follow all the tractor’s manufacturers
safety recommendations.
Iron & Oak
6
800-817-1005
✘
Do not, under any circumstances, alter your log splitter. This equipment was
designed and engineered to be used in accordance with the operating
instructions. Altering the equipment, or using the equipment in such a way
as to circumvent its design capabilities and capacities, could result in
serious or fatal injury and WILL VOID THE WARRANTY.
✘
Never operate, or allow anyone else to operate, this equipment while
under the influence of medication, drugs, or alcohol.
✘
Never wear loose clothing or jewelry that may get caught or become
entangled in the log splitter.
✘
NEVER place hands or feet between log and splitting wedge or between log
and ram during the forward or reverse stroke.
✘
DO NOT STRADDLE OR REACH ACROSS THE SPLITTING AREA WHEN
OPERATING THE LOG SPLITTER.
✘
Do not step over your log splitter when the tractor is running because you may
trip or accidentally engage the ram.
✘
NEVER attempt to load your log splitter while the ram is in motion.
✘
Only use your hand to operate the control lever. NEVER use your foot, knee, a
Log Splitting Safety
✔ Always keep your fingers away from any cracks that open in the log during the
✔ ALWAYS make sure that both ends of the log you are splitting are cut as square
✘
NEVER try to split two logs on top of each other.
rope, or any other extension device.
splitting operation.
as possible. This will prevent the log from sliding out of position while under
pressure. Logs should be 24 inches or shorter in length.
✘
Never pile logs to be split in a manner that will cause you to reach across the
log splitter.
✔ ALWAYS keep full attention on the splitting zone to prevent injury. Hazards
can arise from wood defects (knots, irregular shapes, etc).
800-817-1005
7
Iron & Oak
Maintenance and Repair
✔ Follow all safety rules, because most accidents involving the operation,
maintenance, or repair of products occur because th e assembler/
owner/operator failed to observe basic safety rules or operating instructions.
✔ ALWAYS inspect your log splitter before each use. Make sure all nuts, bolts,
screws, hydraulic fittings, hose clamps, etc. are securely tightened.
✔ ALWAYS check the oil level in the hydraulic oil tank.
✘
NEVER operate your log splitter when it’s in need of repair or is in poor
mechanical condition.
✘
NEVER make alterations to your log splitter in any manner. Such alterations
may cause the log splitter to become unsafe and WILL VOID THE
WARRANTY.
✘
NEVER attach a rope or extension to the control lever or add width or height to
the splitting wedge. Such ALTERATIONS may cause the log splitter to become
UNSAFE and WILL VOID THE WARRANTY.
✘
ALWAYS clean the unit after each use. If possible, store the unit inside or cover
it completely, if stored outside.
Iron & Oak
8
800-817-1005
Assembly Instructions
TMVH02/PTO
Qty.
Valve Assembly
1
Control Lever (valve)
1
Knob (valve lever)
1
Valve Link
3
Clevis Pins
3
Cotter Pins
Shipping List
The following charts contain the list of parts shipped with your log splitter.
Attaching Handle
1. Attach the valve control handle to the
valve. First, install clevis pin and hairpin
clip (1) through the bottom hole on the
valve.
Next, insert the forked end of handle (2)
over pin (1).
Finally, align the hole in the handle with the
top hole in the valve and insert clevis pin
and hairpin clip (3).
800-817-1005
9
Iron & Oak
Assembly and Initial Installation Procedure
1. Attach the tractor mount log splitter to the
three-point tractor hitch, as shown, and
according to the directions found in your
tractor operating manual.
2. Lower the log splitter to the ground. Measure the distances from the inlet and outlet port of the valve to the tractor’s supply
and return port.
3. Attach customer supplied 3/4” 3000
psi hydraulic hose from your tractor’s
hydraulic supply port to the inlet port on
the control valve. Connect a second
customer supplied 3/4” 3000 psi hose
from the tractor’s return port to the outlet
port on the control valve. These hoses
will need Male 3/4” NPT fittings on the
valve end and should be at least 10”
longer than the distance measured in step
2.
Iron &
Oak
10 800-817-1005
4. The log splitter is now completely assembled. Follow the "Start-Up
in the following
section.
Procedure"
800-817-1005
11
Iron & Oak
Start-Up Procedure
Always wear protective gear, such as
safety goggles, tight-fitting gloves without
drawstrings or loose cuffs, steel-toed
Model
TMH13HYD
1. Lubricate the surface of the slide rail with grease. This will help to prevent wear
between the slide plates and the slide rail.
2. Push the valve control handle to the forward position (towards the front of the cylinder)
until the cylinder piston moves forward. (Keep everything away from the splitting wedge
during this step).
3. Cycle the log splitter several times.
4. Push the valve control handle to the retract position and retract the cylinder piston.
The cylinder valve will automatically stop the cylinder from retracting when it reaches the
end of its stroke.
5. Your log splitter is now ready to use.
Iron & Oak
12
800-817-1005
Operation
Iron & Oak Products’ dealer or call the Sales and Service representatives at our
main headquarters. Proper care is your responsibility.
When operating the log splitter make sure you
are standing in the safe operating area, as
shown in these pictures. You must stay in the
safe operating area at all times when the
splitting wedge is in motion (whether extending or retracting). Never place any part of
your body into a position which would cause
an unsafe operating condition.
1. Place the tractor and log splitter on flat, dry
ground. Make sure you read all
recommendations from the “Safety”
section before using the log splitter.
2. Make sure both ends of the log you are
splitting are cut as square as possible.
This will prevent the log from sliding out of
position while under pressure. All logs
should be 24 inches long or shorter.
Do not attempt to operate the log splitter without fully understanding
all our instructions, safety precautions, and/or warnings. If any doubt
or question arises about the correct or safe method of performing anything found in this or other Iron & Oak
Products’
WARNING
manuals, contact your
Never attempt to split wood across the
grain. The log splitter was not designed for
cross-grain splitting. Doing so will damage the log splitter and may cause personal injury.
WARNING
800-817-1005
13
Iron & Oak
tight-fitting gloves without drawstrings or loose cuffs, and
3. Start the tractor. Warm up the PTO pump
and/or hydraulic system by running the
engine at half throttle for three to four
minutes, then advance the engine throttle
control to maximum speed.
4. Use the following photos for the correct
and incorrect methods of splitting logs.
Never split a log using an incorrect or
unsafe method.
a. Place the log on the log splitter. Grasp
the log on the sides near the middle of
the block. Center the log, side-to-side,
on the rail of the log splitter, making
sure that the sawed end is against the
splitting wedge.
Do
ends of
log
UNSAFE method and could result in injury
to your hands.
CAUTION
not
place
splitter.
your hands on
the
log when loading
This
is a very
Before loading and operating the log splitter,
always wear protective gear, such as safety
goggles, face shield, hearing protection,
the
the
WARNING
steel-toed
shoes.
Iron & Oak
14
800-817-1005
b. Using only your hand, push the control
lever forward (towards the log). If the
log moves before it is contacted by the
splitting wedge, release the control
lever and then reposition the log.
Operate the log splitter only when
standing in the safe operating area,
as shown in the picture.
If you find you must hold the log
until the wedge touches it and
holds it in place, be very careful
not to put your hand between the log and
the end plate or the log and the wedge. If
you must, hold the log on top and in the
middle. Remove your hand immediately
when the splitting wedge engages the log.
Never use your hip or any extension device
to operate the valve control handle.
Do
reaching
very UNSAFE
could cause personal injury or even death.
Do
rail while
running.
UNSAFE
method which could cause personal injury
or even death.
CAUTION
WARNING
not
operate the
across the
log splitter by
rail. This is
method
WARNING
not
reach or step across the
the
log splitter is
This
is a very
which
a
800-817-1005
15
Iron & Oak
c. Hold the control lever, extending the
splitting wedge, until the log is split or
the cylinder rod stops at its maximum
travel position. As the log is being
split, DO NO T reach forward and
attempt to catch the split wood — let it
fall to the ground.
d. Once the wedge reaches its full for-
ward travel, pull back on the control
lever to the full retract position. The
ram of the cylinder will automatically
retract into the cylinder. It is not
necessary to hold the control lever as
the cylinder retracts. Stop the wedge if
the log sticks (see caution below).
When the cylinder is fully retracted,
the control valve will automatically
shift to a neutral position.
e. DO NOT load another log or remove
split pieces from the rail until the
wedge has completely stopped and
the control handle automatically
returns to the neutral position.
Depending on
being split,
break
the ground. If a log sticks to the wedge,
place the valve handle in the neutral
position (stop the wedge from retracting)
and carefully remove the log from the
wedge. Allowing the log to remain
attached to the wedge when it is fully
retracted could lead to possible injury
and/or damage to the log splitter.
CAUTION
a
into two
the type of
log
may
pieces
wood
not
always
and fall to
Iron & Oak
16
800-817-1005
Inspection and Maintenance
General Maintenance Check (before operating)
The hydraulic system (hoses, cylinder, and pump) should be carefully inspected before
each use. Also, inspect the mechanical parts at the same time. Make sure all clamps,
nuts, bolts, fittings, etc. are properly installed and tightened.
WARNING
Do not check for leaks with your hand. Leaks can be located by
passing a piece of cardboard or wood around the suspected leak and
looking for discoloration. High-pressure fluid escaping from a very
small hole can be almost invisible. Escaping fluid under pressure can
have sufficient force to penetrate skin, causing serious injury or even
death. If fluid is injected into your skin, it must be treated immediately by
a doc- tor familiar with this type of injury.
Always replace frayed, kinked, or cracked hoses and/or other damaged hydraulic
components with Iron & Oak Commercial Products’ authorized parts and components
specified in the “Parts” section of this manual. Replacement parts from secondary
suppliers (not original Iron & Oak replacement parts) can lead to product damage and/or
personal injury, and will void the warranty.
Should it become necessary to loosen or remove any hydraulic fitting or line, be sure to
relieve all hydraulic pressure by shutting off the tractor and moving the valve control
handle back and forth several times until no cylinder movement is visible.
Storage
Between each use of the log splitter, we recommend applying a rust preventative (WD-40
or equivalent) to any bare metal areas on the top of the rail.
800-817-1005
17
Iron & Oak
Inspection and Maintenance
Mechanical Specifications
(Model
THM13HD)
Three-Point Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Category 1, 2, or 3
Slide Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6” x 6” heavy-duty, formed steel
Wedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 inch, high-carbon steel, compound angle
Force/Tonnage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 tons @ 3000 psi
12.5 tons @ 2000 psi
9 tons @ 1500 psi
Cylinder Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 inches
Log Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 inch maximum
Operating Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Horizontal
Unit Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 lbs.
Hydraulic Specifications (Model TMH13HYD)
Cylinder Size . . . . . . . . . . . . . . . . . 4 x 24 inch, clevis type cylinder with 1.75 inch rod
Safety Release Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Detent, auto return
Iron & Oak
18
800-817-1005
Troubleshooting
The following section will detail procedures for checking your log splitter should you
encounter a malfunction. Iron & Oak Commercial Products, Inc. recommends that you
do not attempt to make repairs to the log splitter. In the long run, it is better to take your
log splitter to a servicing lawn and garden dealer for repairs.
Problem: When the control handle is pushed forward (extend), the wedge does not
Problem: The wedge moves slowly, but will split wood.
Problem: The ram will not automatically retract.
move.
1. Check tractor hydraulic tank to make sure it is properly filled.
2. Make sure the tractor hydraulics are functioning.
4. Disconnect the wedge from the cylinder. Grasp the hydraulic cylinder shaft
and try to pull it out. If the rod comes out easily, you will need to rebuild
or replace the cylinder.
1. Check the output of the tractor’s supply oil.
2. For PTO models check the output of the PTO pump.
1. Check the slide rail or wedge assembly for damage.
2. Push the valve handle to the retract position. If the handle will not stay in
this position, adjust valve detent, as described below.
Detent Adjustment Procedure
a. Locate adjustment screw on lower side of valve body.
b. Loosen locknuts.
c. Turn adjustment screw clockwise one-half turn and retighten locknuts.
d. Start tractor hydraulics and test for detent operation. If detent does not
work, repeat Steps b and c.
3. If adjustment of detent does not correct the problem, replace the valve
assembly.
800-817-1005
19
Iron & Oak
Decals
1
WARNING
Make sure all decals are attached to the log splitter and/or engine and
AR
N
I
are legible at all times.
CONTROL
VALVE
Reverse
Neutral
Forward
2
Iron & Oak
20
800-817-1005
(3) (4)
Item
Part No.
Description
Qty.
1
BR002308
Decal, Operating Safety (set)
1
2
BR002310
Decal, Warning Crush
1 3 BR002521
Decal, Serial Number
1
4
BR002621
Decal, Made in USA
1
5
BR002499
Decal, Iron & Oak
2
6
BR002560
DECAL-PROPER MACHINE LOADING
1 7 787944
DECAL, PINCH POINT-LS
1
(6)
(7)
(5)
7
Parts
Model
800-817-1005
21
Iron & Oak
11
12
8
2
Item Part No. Description Qty.
1 BR026014 Weldment, Rail 1
2 BR021258-03 Weldment, Slide 1
3 BR013102 Guide, Slide (thick part) 2
791636 Slide Guide Spacer (thin part) 2
4 BR013104 Retainer, Slide 2
5 82499 Bolt, Carriage, 1/2-13 x 2-1/2” 6
6 82519 Lockwasher, 1/2” 6
7 82509 Nut, 1/2-13 6
8 BR004057 Cylinder - SMC 4”x24”x1 3/4” 1
9 BR001765 Pin, Clevis, 1/2 x 3” long 1
10 BR001761 Clip, Hairpin, 3/32 x 1-3/4” long 1
9
11 BR008531A Pin, Grooved, 1” dia. 1
12 BR001705 Clip, Hairpin (Cylinder) 2
Note 1: Holes are used to mount optional BR021180 Log Cradle.
10
Note 2: Holes are used to mount optional BR026003SA
Kit - PTO Tank
Note 2
5
3
4
6
Note 1
1
TMH13HYD
Iron & Oak
22
800-817-1005
Item
Part No.
Description
Qty.
1
BR026002
Weldment, Hitch Bracket
1
2
2501930
Pin Assembly, Lift Arm
2 3 BR001282
Lock Washer, 7/8”
2
4
BR001283
Lock Nut, 7/8”
2
5
BR001495
Hitch Pin, 5/8”
2 6 BR001764
Hairpin Clip
2
4
1
3
6
2
5
THM13HD
Item
Part No.
Description
Qty.
1
BR004100HK
Handle Assembly Kit
(Includes handle, clevis, pins, and
hairpin clips)
1
2
BR004100
VALVE-BRAND DETENT 3000PSI-B
1
3
BR001052
Fitting, Straight
1 4 778705
1/2"MPT X 3/4"JIC ELBOW
1
6
BR004119N
Hose, high Pressure
1
800-817-1005
23
Iron & Oak
1
3
4
2
6
THM13HD
Iron & Oak
24
800-817-1005
Warranty
For one year from the date of purchase, Iron & Oak Commercial Products Inc. will
replace for the original purchaser, or repair free of charge, all parts of the Iron & Oak
Commercial Products’ Hydraulic Log Splitter, returned to our factory PREPAID and found
upon inspection by us to be faulty, due to defects in materials or workmanship.
The warranty shall not apply to any unit which has been overloaded or misused or which
has been installed, used, or operated contrary to our instructions, or which has been
repaired or altered by anyone other than our authorized representative.
We shall not be liable for any contingent liabilities arising out of the improper function of
any parts.
We make NO WARRANTY with respect to parts NOT of our manufacture, but we will
carry out the terms of the warranties of their respective manufacturers.
If a service representative cannot be found in your area, call Iron & Oak Commercial
Products at (800) 817 -1005. Have your model and serial number on hand before
calling.
Important Warranty Information
To activate your Iron & Oak log splitter warranty, Iro n & Oak Commercial Products, Inc.
please fill out the information in the form below and mail 20195 S. Diamond Lk.
Rd. STE 100in an envelope to the address listed on the right or Rogers, MN 55374 go
online to www.ironandoak.com
Iron & Oak Log Splitter Warranty
Model: TMH13HYD SERIAL #:
OWNER’S
NAME:
ADDRESS:
CITY:
STATE:
Purchased
From:
Street
Address:
City:
Y
our Signature: Date:
Information
ZIP:
State:
- Please Print -
Zip:
800-817-1005
Iron & Oak
27
Optional Attachments
Log Cradle (Part No. BR021180)
✔ Catches split logs - no more stooping to pick up the split pieces.
✔ Each shelf is infinitely adjustable up to 45 degrees to accommodate various sizes of
logs.
✔ Mounts easily to H-beam rail - all hardware included, requires no drilling or welding on
current model log splitters.
4-Way Wedge Assembly (Part No. BR021270-KIT)
✔
Quickly splits large logs into pieces.
✔
Mounts easily to H-beam rail - all hardware included, requires no drilling or welding on
current model log splitters.
✔
Easy to remove - quickly slide off the top.
800-817-1005
Iron &
Oak
28
PTO Kit (Part No.
v
Increases splitting force and cycle
v
Easy to
v
Mounts easily to H-beam rail - all hardware included, requires no drilling or welding on
current model log splitters.
install.
BR026003SA)
time.
800-817-1005
Iron & Oak
29
Notes
Iron & Oak
800-817-1005
30
Notes
05/14
Iron & Oak Commercial Products, Inc.
20195 S. Diamond Lk Rd, STE 100
Rogers, MN 55374
Phone: 800-817-1005 (Toll Free)
Fax: 866-779-9963
E-mail: sales@ironandoak.com
Web Site: www.ironandoak.com
THM13HD
Loading...