Brave SlimDP - 01
Brave SlimDP - 02
Brave SlimDP - 04
User and Service Manual
Version 2.6
Brave – Door Entry System
Welcome
Congratulation on purchasing the Brave SlimDP „BRAVE Slim Door Phone‟,
which is a continuation of the successful SlimDP „Slim Door Phone‟.
The Brave SlimDP is a universal project with the title “BRAVE” with different
designs bringing a wider spectrum of functions and possibilities.
This manual is for the following options:
Brave SlimDP – 01 - 1 button
Brave SlimDP – 02 - 2 buttons
Brave SlimDP – 04 - 4 buttons
For all variants is possibilities with Amplifier (need external power DC 12V)
Brave SlimDP – 01A - 1 button
Brave SlimDP – 02A - 2 buttons
Brave SlimDP – 04A - 4 buttons
Basic functions of the new line
Electronic volume control without the need to open the front cover;
Programmable tone detection for call disconnection or repeat calls;
Programming with a DTMF phone or USB cable from a PC;
24 digit telephone numbers including * # Flash and Pause;
LED backlit name tags;
Manual Version V2.6 22.10.2013
Alphatech spol. s r.o.
Jeremenkova 88
140 00 Praha 4
Tel/fax: 272103334
www.alphatech.cz / info@alphatech.cz
Table of Contents
1 BASIC FEATURES ............................................................................................. 6
1.1 FEATURES ............................................................................................ 6
1.2 TERMINOLOGY ...................................................................................... 7
1.3 BRAVE SLIMDP VERSIONS AND DIFFERENCES ......................................... 8
1.4 UNIT FEATURES ..................................................................................... 8
2 INSTALLATION ................................................................................................. 9
2.1 OPENING, WIRING, WALL MOUNTING AND SETTINGS ................................. 9
2.1.1 Name card panel ....................................................................................... 9
2.1.2 Uncover control elements ......................................................................... 9
2.1.3 Wiring and wall mounting ...................................................................... 10
2.1.4 Switches .................................................................................................. 12
2.1.5 Voice level ............................................................................................... 13
2.2 LOCATION OF DOORPHONE COMPONENTS ........................................... 14
2.3 CHANGING NAME CARDS ...................................................................... 15
2.4 FINAL CLOSING OF DOORPHONE ........................................................... 15
2.4.1 Covering control elements ...................................................................... 15
2.4.2 Replacing name card panel .................................................................... 15
2.5 CONNECT THE KEYBOARD ................................................................... 16
2.6 CODE RELAY (COSW) ......................................................................... 17
2.7 OTHER ACCESSORIES .......................................................................... 18
2.7.1 Time Relay .............................................................................................. 18
2.7.2 Power supply 12V AC ............................................................................. 18
2.7.3 Power supply 12V DC ............................................................................. 18
2.7.4 USB Programming cable ........................................................................ 18
3 DOOR ENTRY SYSTEM OPERATION ........................................................ 19
3.1 SIGNALLING OVERVIEW ........................................................................ 19
3.2 CALLER AT THE DOOR .......................................................................... 20
3.3 RELAYS REGIMES ................................................................................ 21
3.4 PERSON IN THE BUILDING ..................................................................... 21
3.4.1 Outbound call ......................................................................................... 21
3.4.2 Incoming call .......................................................................................... 22
3.4.3 Door Entry System with keyboard – module SlimKey ............................. 22
4 PARAMETER PROGRAMMING ................................................................... 23
4.1 PROGRAMMING WITH THE HELP OF A PHONE ......................................... 23
4.1.1 Entry into the programming .................................................................... 23
4.1.2 Parameter programming ........................................................................ 23
4.2 PROGRAMMING WITH THE HELP OF A PC – PROGRAMME BRAVESET ...... 24
5 DESCRIPTION OF PROGRAMMABLE PARAMETERS .......................... 25
BRAVE SlimDP – User and service manual 5
5.1 DIRECT DIALLING - MEMORY ................................................................. 25
5.2 RELAYS .............................................................................................. 26
5.3 BASIC PARAMETERS ............................................................................ 31
5.4 TIME PARAMETERS .............................................................................. 33
5.5 SYSTEM PARAMETERS ......................................................................... 37
5.6 BASIC SETTING AND DELETION ............................................................. 43
5.7 END OF PROGRAMMING ....................................................................... 43
5.8 PARAMETER OVERVIEW ....................................................................... 44
6 TECHNICAL PARAMETERS......................................................................... 47
6.1 ELECTRICAL PARAMETERS ................................................................... 47
6.2 MECHANICAL DIMENSIONS ................................................................... 47
7 TABLE FOR EASY PROGRAMMING .......................................................... 48
8 DRILLING MASTER BOARD ........................................................................ 52
6 BRAVE SlimDP – User and service manual
1 Basic features
1.1 Features
Voice communication is powered from a telephone line
Impulse and tone (DTMF) options
Storage of 2 24-digit long numbers per button (including*, #, Flash and
pause)
Option to prolong a call with * or #
Option to connect one electronic locks, to open doors
Potential to use up to 6 relay regimes (for electrical lock, an additional
bell, lighting etc.)
Two codes to disconnect the Door Entry System from a phone
One code to open doors from the phone for 1-impulse and one code
for 2-impulse
3 x 6 code locks for relay (password from door buttons)
Can be connected electrically secure lock on the switch (serial
activation code - COSW)
Option to disconnect a call by the repeated pressing of a button
Option to switch on a „baby call‟ regime (no number dialling)
Option to switch on a regime to suppress the DTMF connection from
the microphone
Option to switch on a „ticking‟ sound into a call to announce another
call
Option to switch on acoustic signalling for relay connection
Option to set the number of rings before connecting a call
Programmable parameters for tone options Flash length and Pause
length
Programmable parameters for acoustic signalisation
Programmable parameters for tone detection
Electronic volume setting without the need to open the front cover
Version A is with integrated 1W amplifier
Programmable with PC, via USB cable, and remote DTMF
programming
Integrated regulated heating of the PCB
BRAVE SlimDP – User and service manual 7
1.2 Terminology
Telephone line Analogue (2 conductors) connecting to a public telephone
network (public line) or to a local telephone system (local
line).
Line connection The start of a telephone connection (the same as picking up a
phone handset).
Line disconnection End of connection (the same as replacing a phone handset).
Option DTMF - a tone option combination of two tones (chooses also
special signs * and #, uses breaking the loop Flash)
Impulsive – option by breaking the loop (chooses only digits)
Incoming call Connection between a Brave and a phone made by selecting
an option on the phone. The Brave connects the call after set
number of rings. The Brave can be programmed from the
phone following a connection by inputting a password.
Outbound call Connection between the Brave and a phone made by choosing
an option on the Brave (i.e. Pressing a button).
Call connection Signalised when following the dialled number is picked up.
This signal is not available on an analogue line, but the ringing
tone ends and a connection begins. It is difficult to identify the
exact moment this occurs.
Code lock Function for relay connections by inputting a combination of up
to 4 buttons or keyboard keys (after pressing the key symbol)
Code relay between Doorphone Brave and the electric lock can be
connected code relay (COSW - CodeSwitch), which is located
at the lock and lock activates only when is the same the
specified serial combination of the Brave and set the code on
the board relay (COSW).
External code Combination of 1-2-or-4 buttons or 10 keyboard keys (after
pressing the key symbol) for a relay connection. External =
being input on the Brave outside the building
Internal code Digits combination dial from phone for relay activation (DTMF).
Internal = dial by phone – inside building ( phone connected to
other PBX extension)
The manufacturer continuously improves the product firmware. The
technology used allows you to upload to Brave the latest version of the
firmware any time using a standard computer with BraveSet and USB
cable. The latest version of the firmware is available at
http://www.alphatech.cz
8 BRAVE SlimDP – User and service manual
1.3 Brave SlimDP versions and differences
The Brave door entry system is conceived as system that provides a
final solution based on a modular design. The features and parameters that
are available to, and can be set, differ for each version of the Brave. It is
therefore necessary to set the parameters for all versions including any add-on
parameters for each version.
Available Features:
basic models: Brave SlimDP – 01 - 1 button
Brave SlimDP – 02 - 2 buttons
Brave SlimDP – 04 - 4 buttons
models with amlifier: Brave SlimDP – 01A - 1 button
Brave SlimDP – 02A - 2 buttons
Brave SlimDP – 04A - 4 buttons
Itegrated amplifier is only HW solution, all programable parameters is same.
Parameters that are not specified in this manual is not recommended to
change because they are not available for the version of Brave SlimDP.
If you do happen to change a parameter, so it is recommended to make the
defaults parameters.
1.4 Unit features
Three versions are available plus keyboard :
Brave SlimDP–01 Brave SlimDP–02 Brave SlimDP–04 Keyboard
Canopy
BRAVE SlimDP – User and service manual 9
2 Installation
This compact unit is fixed by 2 screws to the wall.
2.1 Opening, wiring, wall mounting and settings
2.1.1 Name card panel
1. Every unit is supplied with a
special key which is used to
release the name cards on the
front panel. Push the key into
the hole in the speaker grille
(see figure - 1).
2. Push the name card panel
down and then push it towards
to grille (see figure-2).
3. The panel will be released.
Pull it towards you to remove
(see figure – 3).
2.1.2 Uncover control elements
4. Push the aluminium speaker grille down (see
figure – 4).
10 BRAVE SlimDP – User and service manual
2.1.3 Wiring and wall mounting
5. Use the wall mounting
template at the end of
the manual to mark the
position for the screw
holes and cable
connection on the
mounting surface. Drill
the holes.
6. Feed the cable
(analogue line, power
supply, lock – see
figure - 6) through the
cable hole.
Fix the panel to the wall
using the screws and
rawlplugs supplied.
Drill draw is on page 52
Note: Some materials such as metal and wood may require special
screw types.
To power the unit for voice, connect the telephone wires into the terminal
(on the right side). Using either a standard analogue phone line or an analogue
extension on a PBX.
For the external power supply, connect to the terminal "12V" external power
supply AC min. 10V / max. 18V or DC min. 12V / max. 24V.
The energy consumption of a connected electrical (magnetic) lock (0,5A –
1,0A) determines the load on the power supply. If you activate the heating
feature the PCB current will climb to about 150mA. We recommend power
supply AC 12V/1A for normal version and we recommend power supply DC
12V/1A for version with amplifier.
BRAVE SlimDP – User and service manual 11
The wiring of relay contacts is explained in the next picture. The symbol
"NO" means contact normally open, "COM" means sharing output (central) and
"NC" means contact normally closed. The relay contact is isolated from the
other circuits on the board. For the variants of lock connection see the picture
below.
Wiring of standard and magnetic (inverse) lock
7. A special USB cable enables the doorphone to be connected to a PC for
programming of individual parameters. A dedicated Windows program is
included on the CD (requires version W98SE or higher).
Under no circumstances use 120V or 230V direct current (DC)! This
can be solved by the use of contactors (power relays).
Power
supply
lock
Telephone
line
12 BRAVE SlimDP – User and service manual
2.1.4 Switches
8. The switch marked HEAT (see figure – 8)
activates heating of the PCB. This is for
increased resistance against humidity. To
use this feature you must connect an
external 12V power supply.
9. The switch marked SERVICE (see figure – 9)
is required for programming the unit when
the password is forgotten. It is performed by
ordinary phone (DTMF – tone dial ).
The switch is
The PCB heating has two major benefits. Firstly, it warms the board during
winter time (temperatures under -20 C, most circuits have warranty operation
down to -20 C) and secondly it helps to protect the PCB against humidity when
installed outside.
Note: Door entry system Brave SlimDP is designed in such a way that it is
possible to connect 10-18V AC or 12-24V DC to the terminals 12V (polarity is
unimportant). The motherboard heating system has a regulator so that
resistors won‟t burn out at a higher voltage.
BRAVE SlimDP – User and service manual 13
2.1.5 Voice level
The principle of setting acoustic paths:
Here we have three parameters 71.72 and 73 Using the interaction of these
parameters can be set to sound in different conditions.
1. quiet environment parameters 71,72,73 are set to 7
2. environment where is a strong ambient noise at the communicator and
quiet environment at the phone. Here is both necessary to reduce the
microphone gain (parameter 72 = 1-3) and also change the ratio of the
parameters 71/73 way 73 enlarge the the parameter (parameter 73 = 11-
15) and 71 parameter smaller value (71 = 2-4)
3. environment where is a strong ambient noise at the phone and quiet
environment at the communicator. Here we leave the parameter value of
72 = 7 and 73 and 71 parameters set as follows - parameter71 = 11 to 14
and 73 = 2 to 4
The principle of settin parameters is - signal from the microphone is amplified
by the sum of parameters 72+71 = volume of microphone and signal to the
speaker is amplified by the sum of parameters 71+73 = volume of speaker.
To switch the direction of the ratio is evaluated parameters (threshold) 73/72.
- If parameter 72 is greater than the parameter 73, thus favoring the
direction from the microphone. We choose when the direction to the
phone is interrupted.
- If parameter 73 greater than parameter 72, thus favored direction to
the speaker. We choose this if the interrupted sound in the speaker of
communicator.
14 BRAVE SlimDP – User and service manual
2.2 Location of Doorphone components
All mounting, control and setting elements are located under the speaker front
aluminium grille.
.
PC connector
SlimDoorPhone
fixing screw
hole
Service switch
Loudspeaker
Heating
activation
12V =/~ for
relay, light and
heating
Relay
Telephone
line
connection
Microphone
Buttons
Hole for lead in cable
LED for
lighting
BRAVE SlimDP – User and service manual 15
2.3 Changing name cards
Name card panel (2.1.1on page 9) has spaces
to insert printed name cards. Insert name cards
from top (see picture). Cards can easily be printed
with pictures as well as text using the included
software. The card outline is marked for easy cutting .
2.4 Final closing of Doorphone
2.4.1 Covering control elements
1. Push aluminium speaker cover back up (see
picture). Take care when re-covering the speaker.
The aluminium edge of the speaker may be gently
pressed if required.
2.4.2 Replacing name card panel
2. Push key into hole in speaker grille
as far as possible. (see figure -2).
3. Push name card panel upwards and
push the bottom edge in (see figure
- 3).
4. Push the name card panel back
down behind the lip of the casing
(see figure - 4).
pocket
Panel with
cards
16 BRAVE SlimDP – User and service manual
2.5 Connect the Keyboard
Keyboard work as separate code lock, he has connection power supply
12V, input for departure button and one relay with change-over contact. In case
connection by special cable keyboard with Doorphone characteristics those
code lock expand and keyboard can be use not only to control relay in
keyboard, but relay in doorphone Doorphone contol too and use so 10 codes
for one and 10 codes for second relay. Further it is possible keyboard use to
dialling numbers. Exit button can control one or the other relay and relay in
keyboard it is possible control from phone during conversation too
(parameter.30). Code lock for relay in Doorphone from buttons stays
conserved.
Connection by special cable is make that way will you use
programming connectors 8pin. To programming from PC is usings same USB
cable USB-KABslim and program ID-Manager is in new version 2010 equipped
also by program for setting keyboard.
To basic function is necessary have connected to Doorphone
telephone line and to keyboard 12V. 12V for heating board and power supply
of relay in Doorphone can use from same source and it is possible use also for
power supply of locks. Recommended is use low power locks.
The choice is entered by gradual pressing of buttons with digits. Firstly
the key symbol must be pressed to enter a password. When pressing X, the
guard will hang up.
BRAVE SlimDP – User and service manual 17
2.6 Code relay (COSW)
For the switch (relay) is available function code relay (COSW
CodeSwitch). It serves primarily to secure transmission of information by
switching the electric lock. When using this function is not possible connecting
or disconnecting the voltage at the terminals to lock this lock activated.
Activation is performed only when positive result compared serial information
transmitted between Brave and
the board code relay
Brave is set in several
codes to activate the relay code.
Relay can be activated codes
for one or two impulses can
differentiate activated from the
phone (DTMF) or from keys
(keyboard). The last option is
the activation code in another mode switch than the lock.
The code information is 8 bits, but the code is 4 bits with security 4 bits which is
total of 8 bits. Practically, this is performed so that after activation the switch is
first transmits the serial code, and if they agree, so code relay connects the
electric lock.
The code relays can be connected in parallel to increase the number of
switches, but can never combine connections electric lock and the code
relay parallel!
18 BRAVE SlimDP – User and service manual
2.7 Other accessories
2.7.1 Time Relay
The time relay enables wider
functionality of the relays. It is a
separate product and detailed
instructions can be found at
www.alphatech.cz
2.7.2 Power supply 12V AC
A 12V/1A AC alternative power supply is
recommended for the Brave SlimDP
normal version. This is not a part of
delivery and must be ordered separately.
Further details of power supplies and
electric locks can be found at
www.alphatech.cz
2.7.3 Power supply 12V DC
A 12V/1A DC alternative power supply is
recommended for the Brave SlimDP
version with amplifier. This is not a part
of delivery and must be ordered
separately. Further details of power
supplies and electric locks can be found at
www.alphatech.cz
2.7.4 USB Programming cable
The USB cable is the same as that used for
the SlimDP door entry system. The USB
drivers can be found on the web site
www.alphatech.cz
BRAVE SlimDP – User and service manual 19
3 Door Entry System Operation
The Brave SlimDP door entry system‟s functions are set by establishing
parameters (see the chapter on parameter programming page 23).
3.1 Signalling overview
Brave SlimDP acoustic signals that occur during its operation. Samples
of sounds can be listened to in the setting programme „BraveSet‟.
State
Tones
Tone frequency
Pick up line type 1
–▄▔▄▔▀–
980-1333-1650
Disconnection of line type 1
–▀▔▄▔▄–
1650-1333-980
Pick up line type 2
–▄▔▀–
800-1067-1200-1333
Disconnection of line type 2
–▀▔▄–
1333-1200-1067-800
Confirmation of command from the phone
––█––
800
Ticking during a call
─┴─┴─
Notice about the end of a call
–▔–▔–▔–
1333
Relay switch signal
─▒▒▒▒▒▒─
Modulated
Entry into programming from the phone
–▄▔▀–
980-1067-1180
Programming from the phone
––▓–▓–––––
Modulated
Parameter confirmation
––█––
800
Entry into programming from the PC
–▄▔▀–
980-1067-1180
Line connection (Reset)
–▔–▄–▔–
1850-1067-1850
Error (generally something is not right)
–▔–▔–▔–▔–▔–
▔–
800
Empty memory (no number is programmed)
–▄▔▄▔▄▔▄▔–
1300-2100
It is useful to know what tones the Brave SlimDP plays during
installation as it will assist in the analysis of its state and operation. The
sounds can be turned off in several levels (parameters 61,62,63 and 65).
To play and listen to the sound signals go to: www.alphatech.cz/zvukova-
signalizace-3.html
20 BRAVE SlimDP – User and service manual
3.2 Caller at the door
The door entry system‟s buttons are labelled in the same way as normal
doorbell buttons. Visitor finds the appropriate name (for example Mr Smith)
and presses the button. The Brave will pick up a line, "plays" the pick up line
tone (if it is not prohibited para.62) and dials the phone number saved under
that button (parameter 1 or 2 depending on system regime). From the Brave‟s
speaker a ringing tone will be heard and Mr Smith‟s phone will ring. As soon
as Mr Smith picks up he can talk to his visitor. If an electric lock is also
connected to the Brave, Mr Smith can press a DTMF code on his phone and let
visitor in. If he puts down the phone the Brave will disconnect. If the call lasts
longer than the pre-set limit (parameter 52), 10sec before disconnection the
Brave will send a line disconnection tome, but Mr Smith can dial * or #
(parameter 42), to prolonged the call for the length of time set in parameter 52.
The dialled number depends on the regime mode, which is set in the
system (parameter 47):
- Regime Day/Night = if the system is in „Day‟ mode, it dials the number set
in parameter 1, if the system is in „Night‟ mode, it dials a number set in
parameter 2. The switching over of regimes manually is set in parameters
45,46.
- Regime 2 groups of numbers = the first press of the button always dials a
number set in parameter 1. Following the repeated pressing of the same
button, when it detects a busy tone (10sec after choice), or after a pre-set
number of rings (parameter 56) the system dials a number from the
second group (parameter 2). After another press of the same button the
system will again dial the number from the first group (or after detecting a
busy tone on the dialling of a number from the group 2 the repetition
ends).
If a visitor presses the button after the system has picked up, the system
will disconnect for a length of time as set in parameter 54 before it picks up the
line and dials a new number. The number choice takes place either by tone
(DTMF) or impulse according to the setting in parameter 41. There is one
more option, disconnection of line after repeat pressing of the same button
(parameter 4*).
It is possible to control a relay switch (code lock) with the first 4 buttons.
If visitor at the door presses buttons in the correct combination according to a
pre-programmed code (parameter 32-34) and the length of time between
presses isn‟t greater than the pre-set time (parameter 53) the system picks up,
switches the appropriate relay (if it is set in mode m=1) for the length of time
given in parameter 37 or 39,30 and then disconnects.
Relays can switch on one or two impulses depending on control code
with the length of time between impulses set in parameter 30. See Tab. 1.
BRAVE SlimDP – User and service manual 21
3.3 Relays regimes
Regime m = 1 (parameter 3111 and 3121)
Action
Note
Parameter
Relay
Evaluation of correct
internal code from
the buttons
3211-3215
According to setting
Day/Night
3311-3315
3411-3415
321*
According to setting
Day/Night
331*
341*
Internal code from
the phone
Option to choose 1 or 2
digits of code
2 digit code is basic and
it is possible to shorten it
by using * in the first
place of code during
programming
351
361
Regime m = 4
Action
Note
Parameter
Relay
Press buttons
Any number of button
other than in 311*
3114
Button set in 311*
3114
Regime m = 6
Action
Note
Parameter
Relay
Press of the button
Any number of button
other than in 311*
3116
-
Button set in 311* or 312*
3116
Note t1 – time of connection of relay 1 (parameter 371)
t2 – time between impulses of relay 1 (parameter 301)
Tab. 1 Table of relay controls
3.4 Person in the building
The person in the building means the person who is in telephone contact
with the Brave entry system (i.e. Mr Smith).
3.4.1 Outbound call
An outbound call is a call from the Brave system (i.e. started by a visitor).
Once the system has been dialled, a phone inside of the building rings and on
pick up it is possible to talk to the visitor at the door. By choosing a code it is
possible to switch on a relay (parameter 35) if it is set in mode m=1, switch
over the Day/Night regime (parameter 45, 46) and disconnect the connection
(parameter 43). 10sec before the end of the call (parameter 52) the system
22 BRAVE SlimDP – User and service manual
sends a notice about the end of the call but choosing a code (parameter 42) it
is possible to pro-long the call. By replacing the handset the call is terminated
(the switchboard phone will send a system busy tone and the system will
disconnect). There is one more option, disconnection of line after repeat
pressing of the same button (parameter 4*).
3.4.2 Incoming call
An incoming call is a call to the system (started by a person inside the
building). After choosing the branch the system is connected and the line
rings, following a set number of rings (parameter 51) the system will then pick
up and it is possible to speak. The options are the same as an „outgoing call‟
(chapter 21)
One exception is in the first 10sec. when it is also possible to input „# and
a service password‟ (parameter 44) directing the system to go to the
programming regime.
Another exception is during incoming call and DIP1 is switched to on
("SERVIS") when the system also goes to the programming regime
(without a service password).
The final exception is relay controls (parameter 381), when an incoming
call can disable the relay controls.
3.4.3 Door Entry System with keyboard – module SlimKey
If a keyboard module is connected to the system, then it is necessary to set
the following parameters:
Parameters for control second relay is in parameters same for relay 1
(inside Brave SlimDP), but with index relay 2.
For using features in SlimKey is need set in SlimKey parameter –
“connection with SlimDP” to “on”. Next is possible dial telephone numbers from
keyboard and control relay 1 by code from SlimKey and from exit button
connected on SlimKey. This settings is on SlimKey, in Brave SlimDP is
connection with SlimKey detected automaticaly.
BRAVE SlimDP – User and service manual 23
4 Parameter programming
4.1 Programming with the help of a phone
4.1.1 Entry into the programming
There are two ways to enter the Brave‟s programming system:
1. With the help of a password –incoming calls only! – pick up a phone
and dial the number that the Brave is connected to (either the number of
the branch, if you are connected to a switchboard line, or the number of the
line to the building, where the Brave is and ask be connected to the branch to
which the Brave is connected). The brave will pick up (you will hear the
pick-up tone – see chapter 3.1 page 19) within 10 secs. press „#xxxx’,
where xxxx is the service password to enter the programme system (in
the basic setting xxxx=0000), if correct there will be a programming
entry tone followed immediately by a programming tone (see chapter
3.1 page.19).
2. With the help of DIP 1 "SERVICE" –incoming call only! – connect to
the Brave as in part 1 above, but where the DIP switch is in position 1
“on”, the Brave will go straight to the programming regime – you will
hear the pick-up tone for entry to programming followed immediately by
the programming tone (see chapter 3.1 page.19).
Do not forget to put DIP switch to position “off” at the end.
4.1.2 Parameter programming
The default state for programming is announced with a programming
tone, the Brave always returns to this state after a specified time (5sec),
whether you started programming or not.
There are two types of parameters used during programming. These are
parameters with a fixed length, which is the majority of them, when
programming is confirmed after it fulfils the mandatory length and is
immediately „written in‟ with a confirming tone and parameters with variable
length (parameters 1,2,32,33,34) when the confirmation is made only after
time of inaction (5 sec). The only case when there is an immediate „writing in‟
of parameters is when the maximum number of „written in‟ signs (numbers) are
filled up, for parameters 1 and 2 it is 24, for parameters 32,33,34 it is 6.
If you input a number (sign) that is unacceptable during the programming
the Brave immediately sends an error tone, the parameter is not „written in
„and the Brave reverts to a default state where it is possible to either repeat the
parameter programming or start programming a different parameter.
The Brave will automatically disconnect form the programming regime
after a period of inaction, 30 sec. With each DTMF tone dialled the time will
always resets to 30 sec. It is also possible to end the programming regime by
choosing parameter 9.
24 BRAVE SlimDP – User and service manual
Note. If you want to keep a connection opened during the programming (prolong the 30
sec time) regime (i.e. before a customer decides what else he wants to be set) then you
can press * or #, the Brave immediately answers with an error tone but will prolong the
time before disconnecting.
4.2 Programming with the help of a PC – programme
BraveSet
To programme the Brave with the PC you will; need to use the special
cable USB-KABslim and programme BraveSet. The Brave will also need to be
connected to a telephone line.
Procedure:
- Connect the Brave SlimDP to the line;
- Connect Brave SlimDP to the PC via the USB cable. The Brave will pick
up a line and within 3 seconds a tone for programming entry will be heard
(see chapter 3.1 Page.19).
- Run programme BraveSet. Until the USB is disconnected the Brave is
connected to the PC and is in programming regime and will not run any
other operations. If you lose connection, you will need to reconnect the
USB cable – the Brave will then pick up.
- Connection between the Brave and the programme is indicated by the
firmware on the bottom.
For ease of orientation the parameters in the BraveSet programme are
marked with the same codes as per the phone programming.
The details about parameter setting can be found in „help‟ of the
programme and also on the manufacturer‟s website www.alphatech.cz.
BRAVE SlimDP – User and service manual 25
5 Description of programmable parameters
Parameters always start with a fixed/mandatory part (address) followed
by a variable part, which is your choice. The range and explanation is always
under the table, sometimes with examples. Everything is dialled exactly as it is
shown in the table, nothing needs to be confirmed in any way, after writing into
a memory a confirmation tone can be heard and if an incorrect value is input
then an error tone will be heard.
5.1 Direct dialling - memory
Parameter
Value
Meaning
Basic
1
tt nn…
number nn under button tt
-
tt – button number (memory), always input 2 digits [01-04]
nn – telephone number as long as 24 digits that are to be
saved. For saving of other sign choices always use the
assignation as per the table.
Numbers saved in parameter 1 are numbers of the first
group, or numbers of the regime Day.
Basic settings never change or delete these saved
numbers.
Parameter
Value
Meaning
Basic
2
tt nn…
number nn under button tt
-
tt – button number (memory), always input 2 digits [01-04]
nn – telephone number as long as 24 digits that are to be
saved. For saving of other sign choices always use the
assignation as per the table.
Numbers saved in parameter 2 are numbers of the
second group, or numbers of the regime Night.
Basic setting never change or delete these saved
numbers.
Note. The Day/Night regime switch over remains set in the Brave even after a line
disconnection.
Examples of setting:
1. first button is supposed to dial 358 during the day and 0603441296 during the night,
then the programming is - 101358 and wait for ♫, then 2010 *0 603441296 and wit
for ♫
2. second button is supposed to dial 123#1*2Flash3 during day and night, then the
programming is 102123#1 ** 2 *# 3 and wait for ♫, then 202123#1 ** 2 *# 3 and wait
for ♫
meaning
choice
0 - 9
0 - 9
# # *
**
Flash
* #
Pause
* 0
meaning
choice
0 - 9
0 - 9
#
#
*
**
Flash
* #
Pause
* 0
26 BRAVE SlimDP – User and service manual
Note. If you are not using regime Day/night or regime 2 groups of numbers, then it is
recommended to set regime Day/Night (parameter 47) and then set the same code
for switching over Day/Night (parameters 45 and 46). His way it is guaranteed that
Brave will always be in Day regime and you can only programme telephone numbers
for the day regime (parameter 1).
5.2 Relays
Parameter
Value
Meaning
Basic
31
r m
relay r operates in regime m (1-8)
11 21
r – relay number [1 in SlimDP]
m – relay regime [1-6 – not m=5]
regimes m=1, 4, 5, 6 are explained in detail in Relay Regimes Tab. 1 on page
21
m=1 mode relay – switched on with command (internal code) or with a
password (external) 1 impulse for length of time t1 (use for electric locks)
or 2 impulses when it switches on for time t1, off for t2 and again
switches on for t1 (opening of sliding gates).
m=2 is switched on for time when the line is picked up (camera) – switches on
when system picks up and off when it disconnects.
m=3 is switched on for time when the line is picked up and extra time t1 after
disconnection (lights) - switches on for time when the line is picked up
and extra time t1 after disconnection (for this time the line is busy)
m=4 regime button – switched on when any button is pressed and off after t1
(use is for example connection of external bell or siren)
m=6 switches on depending on pressed button (it is set in parameter 31r*). In
this way it is possible to choose only one button for each relay, which
when pressed switches on relay for time t1. This regime is used instead
of connecting separate doorbell to the system.
Parameter
Value
Meaning
Basic
31
r* tt
button tt switches on relay r in regime m=6
(01-04)
01
r – relay number relay number [1 in SlimDP]
tt – button number (memory), always in two digits [01-99]
This parameter is only for relay regime m=6. Value tt determines which button
starts switching on for time t1 of relay r.
BRAVE SlimDP – User and service manual 27
Parameter
Value
Meaning
Basic
32
rp hh...
In regime Day + Night password hh... for
relay r, in order p=1-5 for 1 impulse and
p=* for 2 impulses (11-444444)
-
33
rp hh...
In regime Day password hh... for relay r,
in order p=1-5 for 1 impulse and p=* for 2
impulses (11-444444)
-
34
rp hh...
In regime Night password hh... for relay r,
in order p=1-5 for 1 impulse and p=* for 2
impulses (11-444444)
-
r – relay number [relay number [1 in SlimDP]
p – order [1 - 5] for 1 impulse. 5 passwords (external codes) from Brave‟s
buttons (external code of code lock)
p – order = * to set password (external code) for 2 impulses
hh... – password (external code) for relay switching on from button or
keyboard [2 to 6 places]. Buttons 1 - 4 are programmed as numbers
1-4.
All together 3x12 passwords, depending on the Day/Night setting,
combinations are be input either with the help of the buttons (only butons on
panel – max. 4). Switching on a relay is affected by the relay regime and the
choice Day/Night, if the regime 2 groups of numbers is set, the system is
constantly in regime DAY.
There are several rules that needs to be followed when setting a password:
Choose the first button of password from buttons that are the least
used for direct dialling (-prolonging time).
Be mindful about conformity of numbers (i.e. when 1 password
contains another.
Note. When setting parameter 32,33,34 signs # and * and 5,6,7,8,9,0 are not used
because they are not on the button panel
Parameter
Value
Meaning
Basic
35
r aa
command aa from phone for switching
relay r 1 impulse (00-99,*0-*9)
155 266
r – relay number relay number [1 in SlimDP , 2 in SlimKey]
aa – command (internal code) for switching on the relay from the phone [2
spaces] /1
To set the same commands for both relays (internal code) so that both relays
activate at the same time. It is also recommended that the same command is
set for „relay on‟ and „command to disconnection of system (parameter 43)
aa=bb.
/1 – command is always 2 digits, but if you wish to control relay with a single
digit from the phone, there is an option to input "*a", where a is a single number
and the star represents an empty space and must be in the first place.
28 BRAVE SlimDP – User and service manual
Example:
1 relay switch on internal code 48 – is programmed 35148 ♫
2 relay switch on internal code 8 - is programmed 352*8 ♫
By choosing no 8 on the phone we switch on just the second relay, with option 48 we
switch on both relays
Note: second relay is in SlimKey module, works only if is SlimKey connected.
Parameter
Value
Meaning
Basic
36
r cc
command aa from phone for switching
relay r 2 impulses (00-99,*0-*9)
150 260
r – relay number relay number [1 in SlimDP]
cc – command (internal code) for switching on the relay from the phone [2
spaces]/1
To set the same command for both relays (internal code) so that both relays
activate at the same time
/1 – command is always 2 digits, but if you wish to control relay with a single
digit from the phone, there is an option to input "*a", where a is a single number
and the star represents an empty space and must be in the first place.
Switching a relay on with 2-impulses is used for sliding gates replacing a gate
entry.
Example:
Command for switching on 1st relay 1 impulse is for example *8, the command for
disconnection is *8 and the command for switching on 1st relays 2 impulses is *9.
Programming: 351*8 ♫ , 431*8 ♫ , 361*9 ♫.
If you are in conversation with the Brave, the command to open a gate would be button
9, the first impulse starts and the gate opens, the second impulse stops it, the time the
gate is opened "opened space" is set by time between the impulses (parameter 30)
after people enter press 8, then Brave makes 1 impulse and disconnects, gate closes.
Parameter
Value
Meaning
Basic
37
r ss
time ss [sec] of relay r on for time t1
(01-99)
105 205
r – relay number relay number [1 in SlimDP]
ss – time t1 for which relay 1 is switched on [2 spaces 00-99], where time
00 means 0,5sec
BRAVE SlimDP – User and service manual 29
Parameter
Value
Meaning
Basic
38
r p
relay r control during incoming call
(0/1)
11 21
r – relay number relay number [1 in SlimDP]
p – parameter whether it is allowed p=1 or disallowed p=0 to control relay
during incoming call.
To prohibit „control‟ during an incoming call, for use with relay 2 in mode 1 for
controlling a garage door, so the electronics open the garage door and the car
passing through the door, closes the door. Then control from the phone could
result in a permanently opened door (i.e. the door doesn‟t close because car
didn‟t enter).
Parameter
Value
Meaning
Basic
30
r zz
time zz [sec] between impulses for
switching on relay r 2 impulses- time t2
(01-99)
105 205
r – relay number relay number [1 in SlimDP , 2 in Slimey]
zz – time t2 between first and second impulse for switching on relay 1 [2
spaces 00-99], where time 00 means 0,5sec
Parametr
Value
Description
Default
3#0
p
p = 1 enabled / disabled p = 0 connection
code relay COSW (0/1)
0
p – turns on transmission serial code to activate the first relay.
CAUTION - at activation this function never connect to the circuit electric lock
without board COSW - code relay - threatens to destroy the relay in Brave
communicator!
The following codes may be the same or different for the resolution switching
on multiple parallel connected relay code.
Parametr
Value
Description
Default
3#1
abcd
activation code 1 pulse from buttons
(0000-1111)
0000
abcd – Brave sends a serial code for the code relay (COSW) after
evaluation code from keys (keyboard) namely for 1 pulse
30 BRAVE SlimDP – User and service manual
Parametr
Value
Description
Default
3#2
abcd
activation code 1 pulse from phone
(0000-1111)
0000
abcd – Brave sends a serial code for the code relay (COSW) after
evaluation code from telephone (DTMF) namely for 1 pulse
Parametr
Value
Description
Default
3#3
abcd
activation code 2 pulses from buttons
(0000-1111)
0000
abcd – Brave sends a serial code for the code relay (COSW) after
evaluation code from keys (keyboard) namely for 2 pulses
Parametr
Value
Description
Default
3#4
abcd
activation code 2 pulses from phone
(0000-1111)
0000
abcd – Brave sends a serial code for the code relay (COSW) after
evaluation code from telephone (DTMF) namely for 2 pulses
Parametr
Value
Description
Default
3#5
abcd
activation code from other modes of switch
(0000-1111)
0000
abcd – Brave sends a serial code for the code relay (COSW) after
evaluation code from other modes m of relay 1
BRAVE SlimDP – User and service manual 31
5.3 Basic parameters
Parameter
Value
Meaning
Basic
41
v
Type of choice v – time/impulse
(0/1)
0
v – type of choice v=0 is DTMF tone choice, v=1 is impulse choice
Parameter
Value
Meaning
Basic
42
z
Sign for call prolonging (* / #)
*
z – sign for prolonging a call * or # (10secs. before the end of the call the
Brave sends signal, after pressing this the Brave prolongs the call)
Parameter
Value
Meaning
Basic
43
g bb
Command for disconnecting Brave from
the phone (00-99,*0-*9)
155 266
g – Command order [1-2] (there are 2 to disconnect the Brave from both
relays)
bb – Command for disconnecting the Brave from the phone [2 spaces]
/1 It is advantageous to set the same command for relay switching on
(parameter 35,36) and command for the Brave disconnection aa=bb or
aa=cc.
/1 – command is always 2 digits, but if you wish to control relay with a single
digit from the phone, there is an option to input "*a", where a is a single
number and the star represents an empty space and must be in the first
place (e.g. at parameters 35,36).
Parameter
Value
Meaning
Basic
44
xxxx
Service password (0000-9999)
0000
xxxx – service password to programme from a phone (DTMF)
If you forget the password, the following procedure is recommended:
1. Open the Brave front cover;
2. Switch „DIP 2‟ to „ON‟;
3. Call the Brave;
4. Once the Brave picks up the system is in programming regime. In
this regime it is possible to change the password 44xxxx;
5. Switch „DIP 2‟ to „OFF‟; and
6. Close the front cover.
32 BRAVE SlimDP – User and service manual
Parameter
Value
Meaning
Basic
45
dd
Command for switch over to DAY
(00-99,*0-*9)
11
46
nn
Command for switchover to NIGHT
(0099,*0-*9)
10
Dd command to switch over to the DAY regime [2 spaces] /1
Nn command to switch over to the NIGHT regime [2 spaces] /1
/1 command is always 2 digits, but if you wish to switch over from Day to
Night with a single digit from the phone, there is an option to input "*a",
where a is a single number and the star represents an empty space and
must be in the first place (e.g. parameters 35,36)
Note. The Day/Night switch over regime stays set following line disconnection.
Parameter
Value
Meaning
Basic
47
e
Regime system choice (0/1)
1
e – Choice of regime numbers; e=0 selects numbers from first and second
group, e=1 selects numbers in accordance with the Day/Night regime.
WARNING !! setting this parameter materially affects the number dialling!
Parameter
Value
Meaning
Basic
4*
k
Line disconnection function by repeatedly
pressing a button (0/1)
1
k – Line disconnection by repeated pressing of the same number:
k=0 function is disabled; and
k=1 repeatedly pressing the same button to disconnect the line.
WARNING !! setting of this parameter materially affects number dialling!
BRAVE SlimDP – User and service manual 33
5.4 Time parameters
Parameter
Value
Meaning
Basic
51
q
Number of rings before the Brave picks up
(1-9)
2
q – The number of rings before an incoming call is picked up. The Brave
picks up between rings 2 secs. after detecting the q-th ring. It is possible
to set the number of rings between 1 and 9.
Parameter
Value
Meaning
Basic
52
d
Maximum length of a call (0-9,*,#)
2
d – The maximum length of time for which the Brave is
busy. It is possible to prolong this time during the
call by choosing a key (* or #) from the phone
(parameter 42). The setting of this time is in
accordance with the adjacent table.
Parameter
Value
Meaning
Basic
53
w
Time between button presses (1-9)
2
w – maximum time [in seconds] between button presses [range 1 - 9]
Normal buttons
- Relay switch on – if the time between presses is longer than time w,
then the code will not work correctly.
- Choice of number – if the pressed button is the first number of a
password to switch on a relay then the choice is delayed by time w.
.
Parameter
Value
Meaning
Basic
54
z
Time of disconnection for repeat dialling
(1-5)
2
z – Time [secs.] the Brave disconnects before it picks up again for repeat
dialling (press of a button during a call, detection of busy tone) [range 15].
Time
[min]
Option
0,5
0
1 - 9
1 - 9
15 * 30
#
34 BRAVE SlimDP – User and service manual
Parameter
Value
Meaning
Basic
55
z
Time before commencing a choice (1-5)
1
z – Time [sec] after the Brave picks up, before it commences a choice [range
1-5]. This time is different for each switchboard phone system, but
generally most operate within 2 seconds after a line is picked up.
Parameter
Value
Meaning
Basic
56
hh
Number of rings before it disconnects
(04-99)
12
h After the choice finishes it will start counting CRT (control ringing tones),
if the number is higher than hh, then it will disconnect [range 04-99]. It
repeats the choice if the regime of dialling 2 groups of numbers is set.
Parameter
Value
Meaning
Basic
500
x
Medium frequency of tone detector (1-0)
3 (375-
475Hz)
501
y
Number of busy tones (2-0)
4
502
z
Time length of permanent tone (1-5)
3 (3s)
x Medium frequency of tone detector is set if there is a non-standard signal
from the telephone switchboard.
y Minimum number of busy tones necessary for detection [2-0], where 0
means 10 busy tones.
z Minimum length of time of a permanent tone (for detection of notification
tone at branch switchboard) [1-5 sec].
frequency
[Hz]
x - choice
275-375
1
325-425
2
375-475
3
425-525
4
475-575
5
525-625
6
575-675
7
625-725
8
675-775
9
BRAVE SlimDP – User and service manual 35
Parameter
Value
Meaning
Basic
503
tt
Tone length of time for DTMF (tone) choice
(04-16)
10 (100ms)
504
mm
Time of gap between DTMF tones
(04-16)
10 (100ms)
505
f
Length of flash time (1-6)
1 (100ms)
506
p
Length of time of pause/digit gap (1-0)
4 (800ms)
tt Length of DTFM tone choices is specified by the formulae:
(the entered number) x 10 = time length of tone [ms]
[range 04-16 which is 40-160ms]
m Length of gap between DTMF tone choices is specified by the formulae:
(the entered number) x 10 = time length of gap [ms]
[range 04-16 which is 40-160ms]
f Length of flash is specified by the formulae:
the entered number x 100 = time length Flash [ms]
[range 1-6 which is 100-600ms]
p Length of pause is specified by the formulae:
the entered number x 100 + 400 = time length of pause [ms]
[range 1-0 which is 500-1400ms]
Time p is the simultaneously length of gap between button taps for an
impulse choice.
Parameter
Value
Meaning
Basic
507
uu
Transmit level of DTMF choice v [-dBm]
(04-16)
10
uu Transmission level of (DTMF) choice to the line, the range is -4 to -
16dBm, input the required level where uu=04 is -4dBm, uu=10 is -10dBm
36 BRAVE SlimDP – User and service manual
Parameter
Value
Meaning
Basic
508
p
preemphase DTMF (0/1)
0
509
S
Listening in DTMF – level (1-4)
2
p Preemphase is the ratio of the upper and lower groups of DTMF
frequencies. It is possible to choose ratio 2.2 dB - p=0 (Europe) or ratio
3.2dB - p=1 (Australia)
s Choice of DTMF volume levels (4 levels):
Volume in DTMF [dB]
s - choice
-15 1 -9 2 -3 3 +3
4
BRAVE SlimDP – User and service manual 37
5.5 System parameters
Parameter
Value
Meaning
Basic
61
z
Acoustic signals (confirmation, error,empty
memory, end of call) (0/1)
1
The Brave‟s comes with standard acoustic signals. However, using parameter
“z” it is possible to switch off the acoustic signals. The values are:
z=0 Acoustic signals off; and
z=1 Acoustic signals on.
Parameter
Value
Meaning
Basic
62
v
Acoustic signals introduction/conclusion
(0/1/2)
1
The acoustic signals for the connection and disconnection of a line are standard,
but this may cause false choices with some phone systems. So using parameter
“v” it is possible to switch off these signals. The values required are:
z=0 Introduction/conclusion signalisation is off;
z=1 Pick up and disconnection signalisation on (intro/concl.- type1);
z=2 Pick up and disconnection signalisation on (intro/concl.- type2).
Parameter
Value
Meaning
Basic
63
u
Acoustic ticking signal during a call
(0/1)
0
Ticking during a call is switched off as standard. However, by switching it on you
can differentiate on the switchboard a call from the Brave by a faint ticking. The
values are:
u=0 Ticking into a call is off
u=1 Ticking into a call is on
Parameter
Value
Meaning
Basic
65
z
Acoustic signals for switching on a relay
(0/1)
0
The signal for switching on a relay is standard, z=0. However, it is possible to use
this function when using a uni-directional supply 12V, so when the door lock is
open there is no buzzing so the person at the door won‟t know the door is open.
When set to z=1 the time the relay is switched (door open) then there is a
specific sound.
Note1 This function is available only for regimes m=1
Note2 During the relay switch-on (2 impulses) there is acoustic signal for the
whole time of the sequence (even during gap between impulses).
38 BRAVE SlimDP – User and service manual
Suppression of the reception DTMF from the microphone is off as a default i=0.
It is possible to open the door with a personal dialler without disturbing a person
inside the building. For higher security it is possible to switch on the suppression
function i=1 and stop a person with an unauthorised copy of the DTMF code from
entering.
This function is turned off as standard b=0. By switching on this function b=1 the
acoustic signal for an empty memory is cancelled, so after pressing a button with
an empty memory there is only a beep (confirmation) and a call is activated as if
there were a number.
Warning: During the first 10 seconds of a call the tone detector is inactive (there
is a pause before the switchboard responds or number dialling by the
switchboard).
Default is off m = 0 By enabling the m = 1 mutes the acoustic path at close relay
(1 or 2) in "electric lock" (modes 1 and 5). This feature is there because if you
often use code lock function or exit button, so the switch-on time to hear the tone
exchange. For some customers, this can be distracting.
Parameter
Value
Meaning
Basic
66
i
Suppression of the reception DTMF from the
microphone (0/1)
0
Parameter
Value
Meaning
Basic
67
b
Baby Call – call without the need to
programme a telephone number (0/1)
0
Parameter
Value
Meaning
Basic
68
b
Mute at the lock activated (0/1)
0
BRAVE SlimDP – User and service manual 39
This constant serves a purpose to identify the no.1 button in the composition of
the module. After entering the number of buttons s the button no 1 is moving so
it is always first.
Number of buttons on the main panel
s - choice
1
1
2 2 4
4
WARNING !! setting this parameter materially affects number dialling.
Parameter
Value
Meaning
Basic
6*
t
Delayed start for switchboards with line
testing (Siemens) (0/1)
0
This function is off as standard t=0. By switching this function on t=1 the
processor goes into sleep mode immediately after the line connection, and after
3 secs. The Brave initialises. The line connection after the power supply
connection is then delayed - state switching on/restarting of the switchboard. If
this function is not working and the telephone switchboard still identifies a line
fault, then there is no other option but to use :
BestBox (external module)
mudule SlimKeyboard (include permanent power doorphone from 12V)
Parameter
Value
Meaning
Basic
6#
s
Setting of the number of buttons on the main
panel.
2
40 BRAVE SlimDP – User and service manual
5.6 Parameter setting Hands Free
First ensure that the rubber seal on the microphone fits properly,
otherwise setting the acoustic parameters will be difficult.
Parameter
Value
Meaning
Basic
71
gg
Reception volume 01-16 (16 is the
highest) (SPK)
07
72
ff
Transmission volume 01-16 (16 is the
highest) (MIC)
07
73
rr
Speaker volume 01-16 (16 is the
highest) (TRH)
07
gg/ff/rr Each number is entered as 2 digits with a range 01-16. After receiving a
confirmation tone ♫ the new value is immediately active and can be
tested.
Facilitation: you can also add/reduce the volume with help of buttons on the
phone * = - and # = +
Stops for the maximum and minimum
volume are acoustically signalled (3
tones like the signal for the end of a
call). If you don‟t press anything for 5
seconds then the „set value‟ is saved
and you hear a confirmation tone ♫.
WARNING !! Default values are set by the manufacturer and it is not
recommended that you change them unless absolutely necessary.
Parameter
Value
Meaning
Basic
74
c
Soft transition of switch over (0/1)
1
This function is set to off as standard c=0, it is a character of the semi-duplex
operation switch over on the telephone line. If the character of silencing is too
steep, it is possible to soften it using c=1.
Parameter
Value
Meaning
Basic
75
n
Suppression of background noise (0/1)
1
This function is set to off as standard n=0. If the Brave is installed in noisy
location (train station, busy street, car park etc.) by switching on this circuit n=1
the noise level is set as a default threshold for switching on the microphone and
is not one way opened. This is related to setting of parameters 71, 76, 77.
BRAVE SlimDP – User and service manual 41
Parameter
Value
Meaning
Basic
76
b
Threshold for switching on the microphone
1-4 (4 is the highest)
2
There is a simultaneous signal from the microphone and the speaker on the
telephone line, to ensure that the Brave doesn‟t produce acoustic feedback. In
the Hands Free circuit there are several functioning blocks for supressing this
feedback. The basic one is a circuit for semi-duplex operation, where the
incoming signal weakens the microphone and the signal from the microphone
weakens the incoming signal. Thresholds for switching on the microphone are
set in this parameter, the lower the value the higher the sensitivity of the
microphone. In noisy surroundings it is recommended to use a higher value with
combination of parameters 71,75, 77.
Parameter
Value
Meaning
Basic
77
s
Speed of switching over voice atomisation
1-4 (4 is the slowest)
2
Parameters 75, 76 describes the principle of acoustic feedback and the speed
with which the circuit switches over, the quality of incoming or outgoing sounds
are set with parameter 77.
Parameter
Value
Meaning
Basic
78
l
VA characteristic for line connection (0/1)
1
Nearly every country in the world has different telephone norms and this
parameter enables you to lower the voltage on the Brave‟s terminals to connect
telephone line voltages in active state by 1V. Where it is required the respective
norm I=0 lowers line voltage by 1V, as standard it is l=1.
Switchover time [ms]
s - choice
1
1
2 2 4 3 8
4
42 BRAVE SlimDP – User and service manual
Parameter
Value
Meaning
Basic
79
k
Compensation for loss of conduit depending on
line current (0/1/2)
1
The Brave has a circuit for installations remote from the switchboard (>100m)
that can compensate for the loss caused by a conduit. This function is switched
off as standard k=0, but it is possible to set on 2 levels, depending on the current
that switchboard can supply (short circuit current I0).
Switchboard current
I0
k - choice
Function off
0
20mA-50mA
1
45mA-75mA
2
Parameter
Value
Meaning
Basic
70
uu
Level of signal transmission v [-dBm] (04-16)
10
uu The signal transmission range to the line is -4 to -16dBm, entered is
required level, which is uu=04 is -4dBm, uu=10 is -10dBm ...
BRAVE SlimDP – User and service manual 43
5.7 Basic setting and deletion
Parameter
Value
Meaning
Basic
8#
#
Basic setting
provide
This setting does not affect parameters 1 and 2 (numbers saved in memory)
Parameter
Value
Meaning
Basic
81
Deletes all numbers in 1st group
(regime Day)
82
Deletes all numbers in 2nd group
(regime night)
83
Basic setting only for parameters 3x
only 3..
84
Basic setting only for parameters 4x
only 4..
85
Basic setting only for parameters 5x
only 5..
86
Basic setting only for parameters 6x
only 6..
87
Basic setting only for parameters 7x
only 7..
Parameters 81 and 82 deletes all numbers saved in the button memory.
Parameters 83 – 87 deletes selective basic setting for parameters starting with
3,4,5,6,7. Values for the basic setting are stated for each parameter in the right
hand - column "Basic".
WARNING !!! deletion is irreversible and it would be necessary to
reprogramme them again!
5.8 End of programming
Paramet
er
Value
Meaning
Basic
9
E N D of programming
After choosing 9 programming tone the Brave disconnects.
44 BRAVE SlimDP – User and service manual
5.9 Parameter overview
Parameter
Value
Meaning
Basic
1
tt nn…
number nn under button tt
-
2
tt nn…
number nn under button tt
-
31
r m
relay r works in regime m (1-6)
11 21
31
r* tt
button tt causes switching on of relay r in
regime m=6 (01-04)
1*01
32
rp hh...
In regime DAY + NIGHT password hh...
for relay r, in order p=1-5, for 1 impulse
and p=* for 2 impulses (11-444444)
-
33
rp hh...
In regime DAY password hh... for relay r,
in order p=1-5, for 1 impulse and p=* for 2
impulses (11-444444)
-
34
rp hh...
In regime NIGHT password hh... for relay
r, in order p=1-5, for 1 impulse and p=* for
2 impulses (11-444444)
-
35
r aa
command aa from the phone for switching
on relay r 1 impulse (00-99,*0-*9)
155 266
36
r cc
command aa from the phone for switching
on relay r 2 impulses (00-99,*0-*9)
150 260
37
r ss
time ss [sec] of relay r switch on for time
t1 (01-99)
105 205
38
r p
Control of relay r during incoming call
(0/1)
11 21
30
r zz
period zz [sec] between impulses for
switching on 2 impulses of relay r – time
length t2 (01-99)
105 205
3#0
p
p = 1 enabled / disabled p = 0 connection
code relay COSW (0/1)
0
3#1
abcd
activation code 1 pulse from buttons
(0000-1111)
0000
3#1
abcd
activation code 1 pulse from phone
(0000-1111)
0000
3#1
abcd
activation code 2 pulses from buttons
(0000-1111)
0000
3#1
abcd
activation code 2 pulses from phone
(0000-1111)
0000
3#5
abcd
activation code from other modes of switch
(0000-1111)
0000
41
v
Type of choice v – ton/impulse (0/1)
0
42
z
Sign for call prolonging (* / #)
*
43
g bb
Command for Brave disconnection from
the phone (00-99,*0-*9)
155 266
BRAVE SlimDP – User and service manual 45
44
xxxx
Service password (0000-9999)
0000
45
dd
Command for switch over to DAY
(00-99,*0-*9)
11
46
nn
Command for switch over to NIGHT
(0099,*0-*9)
10
47
e
Regime system choice (0/1)
1
4*
k
Line disconnection by repeat press of the
same button (0/1)
1
51
q
Umber of rings before Brave picks up
(1-9)
2
52
d
Maximum length of call (0-9,*,#)
2
53
w
Time between button presses (1-9)
2
54
z
Time of disconnection for repeat choice
(1-5)
2
55
z
Time before choice begins (1-5)
1
56
hh
Number of rings before disconnection
(04-99)
12
500
x
Medium frequency of tone detector
(1-0)
3 (375-475Hz)
501
y
Number of busy tones (2-0)
4
502
z
Length of time for permanent tone
(1-5)
3 (3s)
503
tt
Length of time for DTMF (tone) choice
(04-16)
10 (100ms)
504
mm
Length of time for gap between DTMF
tones (04-16)
10 (100ms)
505
f
Length of time Flash (1-6)
1 (100ms)
506
p
Length of time for pause/inter-digit gap
(1-0)
4 (800ms)
507
uu
Level of transmission of DTMF choice v
[-dBm] (04-16)
10
508
p
preemphase DTMF (0/1)
0
509
S
Listening in DTMF – level (1-4)
2
61
z
Acoustic signalisation (confirmation, error,
empty memory, end of call...) (0/1)
1
62
v
Acoustic signalisation Intro/Concl. (0/1)
1
63
u
Acoustic signalisation ticking into a call
(0/1)
0
65
z
Acoustic signalisation for relay switch on
(0/1)
0
66
i
Suppression of reception DTMF from
microphone (0/1)
0
46 BRAVE SlimDP – User and service manual
67
b
Baby Call – call without the need to
programme in number (0/1)
0
68
b
Mute at the lock activated (0/1)
0
6#
s
Setting of number of buttons on the main
panel
2
6*
t
Delayed start for switchboards with line
tests (Siemens) (0/1)
0
71
gg
Reception volume 01-16 (16 is the
highest) (SPK)
07
72
ff
Transmission volume
01-16 (16 is the highest) (MIC)
07
73
rr
Speaker volume 01-16 (16 is the
highest) (TRH)
07
74
c
Soft transition of switchover (0/1)
1
75
n
Suppression of background noise (0/1)
1
76
b
Threshold for switching on the microphone
1-4 (4 is the highest)
2
77
s
Speed of switching over voice atomisation
1-4 (is the slowest)
2
78
l
VA characteristic for line connection
(0/1)
1
79
k
Compensation for loss of conduit
depending on line current (0/1/2)
1
70
uu
Level of signalisation transmission
in [-dBm] (04-16)
10
8#
#
Basic setting
provide
81
Deletes all numbers in 1st group
(regime Day)
82
Deletes all numbers in 2nd group
(regime night)
83
Basic setting only for parameters 3x
only 3..
84
Basic setting only for parameters 4x
only 4..
85
Basic setting only for parameters 5x
only 5..
86
Basic setting only for parameters 6x
only 6..
87
Basic setting only for parameters 7x
only 7..
9
E N D
BRAVE SlimDP – User and service manual 47
6 Technical parameters
6.1 Electrical parameters
Parameter
Value
Conditions
Minimum line current
18mA
Line picked up
Minimum line voltage
18V
Line disconnected
Voltage on the line when Brave
picks up (VA characteristic)
< 8V
< 12V 1)
I = 20mA
I = 60 mA
Lead in in disconnected state
< 30uA
U = 60V
Impedance of line ending
220R +
820R paral. 115nF
Line picked up
Bandwidth
300Hz – 3400 Hz
20 - 60mA
Impendence of ringing
> 2Kohm
25 – 60 Hz
Sensitivity of ringing detector
min. 10 – 25 V
Impulse choice
40 / 60 ms
Level of tone choice
-6 a -8 dB 1)
20 – 60 mA
Sensitivity of tone choice
min. -40 dB
20 – 60 mA
Sensitivity of tone detector
min. -30 dB
20 – 60 mA
Power supply for name tag back
lighting, relay, heating and
current circuit for exit button
12V DC(12V-24V) , 12V AC(10V-18V)
Max off take of backlighting and
heating
250mA
12Vss
Max. Voltage of relay contact
48V
When I < 1A
Max. Current of relay contact
1,5A
When U < 30 V
Operating temperature
- 20 to + 60 st.
Level of cover
IP44
1) Potential to change by programming.
6.2 Mechanical dimensions
Dimensions WxHxD 104mm x 153mm x 16mm
Weight 360g
Unit material elox aluminium profile
Name card panel material acrylglas (plexiglass)
48 BRAVE SlimDP – User and service manual
7 Table for easy programming
Fill in the values you want to programme into the empty part of the table, in
the double framed part there are whole programming commands to make
programming easier. You can keep the programmed values in the manual for
future changes.
Meaning
Programming sequence
No of
spaces
description
specify
par.
Fill the values
Number under button 1
Day/1gr.
101
24
Number under button 2
Day/1gr.
102
24
Number under button 3
Day/1gr.
103
24
Number under button 4
Day/1gr.
104
24
Number under button 1
Night/2gr.
201
24
Number under button 2
Night/2gr.
202
24
Number under button 3
Night/2gr.
203
24
Number under button 4
Night/2gr.
204
24
Relay 1 works in mode
m=1 - 6
311
1
Passw. for relay 1 (1 imp.)
Day+Night
3211
6
Passw. for relay 1 (1 imp.)
Day+Night
3212
6
Passw. for relay 1 (1 imp.)
Day+Night
3213
6
Passw. for relay 1 (1 imp.)
Day+Night
3214
6
Passw. for relay 1 (1 imp.)
Day+Night
3215
6
Passw. for relay 1 (2 imp.)
Day+Night
321*
6
Passw. for relay 1 (1 imp.)
Day
3311
6
Passw. for relay 1 (1 imp.)
Day
3312
6
Passw. for relay 1 (1 imp.)
Day
3313
6
Passw. for relay 1 (1 imp.)
Day
3314
6
Passw. for relay 1 (1 imp.)
Day
3315
6
Passw. for relay 1 (2 imp.)
Day
331*
6
Passw. for relay 1 (1 imp.)
Night
3211
6
Passw. for relay 1 (1 imp.)
Night
3212
6
Passw. for relay 1 (1 imp.)
Night
3213
6
Passw. for relay 1 (1 imp.)
Night
3214
6
Passw. for relay 1 (1 imp.)
Night
3215
6
Passw. for relay 1 (2 imp.)
Night
321*
6
BRAVE SlimDP – User and service manual 49
Button choice for 1 relay
m=6
311*
2
Switch on r 1 from phone
1 impulse
351
2
Switch on r 2 from phone
1 impulse
352
2
Switch on r 1 from phone
2 impulses
361
2
Length of time for r 1 switch
on
[sec]
371
2
Control of r 1 during
incoming call
1 / 0
381
1
Control of r 2 during
incoming call
1 / 0
382
1
Length of time between
impulses of r 1
[sec]
301
2
Enable code relay (COSW-sw.1)
0/1
3#0
1
code for activation 1 imp./btn.
0000-1111
3#1
4
code for activation 1 imp./phn.
0000-1111
3#2
4
code for activation 2 imp./btn.
0000-1111
3#3
4
code for activation 2 imp./phn.
0000-1111
3#4
4
code for activation other mode
0000-1111
3#5
4
Type of choice tone / imp.
0 / 1
41
1
Sign for prolonging of call
* / #
42
1
Brave disconnection from
phone
00-*9
431
2
Brave disconnection from
phone
00-*9
432
2
Service password
0000-9999
44
4
Command for switch over
to DAY
00-*9
45
2
Command for switch over
to NIGHT
00-*9
46
2
Regime system choice
1 / 0
47
1
Disconnection by repeat
press of the same button
0 / 1
4*
1
Number of rings for pick up
1-0
51
1
Maximum length of time
[min]
52
1
Time between button
presses
[sec]
53
1
Time of disconnection for
repeat choice
[sec]
54
1
Time before choice
commences
[sec]
55
1
Number of rings before
disconnection
04-99
56
2
Frequency of tone detector
table
500
ms
1
50 BRAVE SlimDP – User and service manual
Number of busy tones
4-0
501
1
Length of time of
permanent tone
1-5
502
sec
1
Length of time of tone
choice
nn x 10
503
ms
2
Gap between DTMF tones
nn x 10
504
ms
2
Length of time Flash
n x 100
505
ms
1
Length of time of pause /
gap
n x100+400
506
ms
1
Transmitting level DTMF
04-16
507
-dBm
2
preemphase DTMF
0 / 1
508
1
Listening in DTMF - level
1-4
509
1
Acoustic signalisation (other)
0 / 1
61
1
Acoustic signalisation
Intro/Concl.
0 / 1
62
1
Acoustic sign. ticking
0 / 1
63
1
Signal tone turning on relay
0 / 1
65
1
Suppression of reception from
microphone
0 /1
66
1
Baby Call
0 / 1
67
1
Mute at the lock activated
0 / 1
68
1
no of buttons on the panel
Type
dependant
6#
1
Delayed start (Siemens)
0 / 1
6*
1
Reception volume (TRH)
01-16
71
2
Transmitting volume (MIC)
01-16
72
2
Speaker volume (SPK)
01-16
73
2
Soft transition of switch
over
0 / 1
74
1
Suppression of background
noise
0 / 1
75
1
microphone switch on
threshold
1 - 4
76
1
Speed of switching over voice
atomization
1 - 4
77
1
VA characteristic
0 / 1
78
1
Compensation for loss of
conduit
0 / 1 / 2
79
1
Level of signalisation trans.
04 - 16
70
-dBm
2
WARRANTY:
Each and every product has been tested before it leaves the factory.
The manufacturer guarantees that the product and its features will work in
accordance with the descriptions in this manual as long as the customer uses
the product in accordance with the manufacturer‟s instructions.
Warranties will be extended when a warranty repair has been undertaken.
Although all warranty repairs will be handled by the manufacturer it is important
that warranty claims are handled through your dealer. Warranty claims should
be accompanied by:
The product in question;
A description of the problem;
Proof of purchase; and
Your full name and address.
The warranty does not cover:
Mechanical, chemical, thermal or any other faults cause by the user
Faults caused by natural disasters
Faults caused by repairs or changes made by the user or any other
authorised or unauthorised person(s)
Purposely done damage
Incorrect use of the product, caused by incorrect installation, programming
etc., and
Damages cause during the transport of the product to and from the
purchaser.
Manufacturer:
Dealer:
Date of sale:
8 Drilling master board
© JR 2013 Version 2.6 X/13
Loading...