1
M1158286A
Loop hose kit for
HBHS300GX, HBHS310GX,
HBHS600GXE, HBHS610GXE, and HBHS620GXE
Owner’s Manual
Instructions for Assembly
Loop Hose Kit: Accessory for Brave Hydraulic Power Packs
About your Loop Hose Kit
This loop hose assembly is ideal for connecting supply and return couplers in a “loop” which is necessary to start the
hydraulic power unit when not coupled to any implement or application. If the loop hose kit isn’t installed and the
engine is attempted to be started the hydraulic system will be in a “dead head” state and damage could occur.
Any Questions, Comments, Problems or Parts Orders
Call Brave Product Support 1-800-350-8739
2
Installation Instructions
Kit Contents
REF
ITEM #
DESCRIPTION
QTY
A
1158277
Hose
1
B
1085800
Female Quick Disconnect Fitting
1
C
1085801
Male Quick Disconnect Fitting
1
D
1081058
Dust Plug
1
E
1081070
Dust Cap
1
F
1159341
Thread Sealant
1
B
A C D F E
3
Installation Instructions
WARNING
ALWAYS shut off the engine, disconnect the spark plug, and relieve system pressure before
inspecting, cleaning, adjusting, or repairing the unit. Relieve system pressure by moving Valve
Control Lever back and forth several times (if applicable).
Tools Needed
• None
Step 1 – Engine off / relieve pressure
Perform all installations with the engine off and hydraulic system pressure
relieved.
• Make sure engine is off and cool.
• Disconnect the spark plug.
• Relieve system pressure by moving Valve Control Lever back and forth several times (if
applicable).
4
Installation Instructions
Step 2
• Apply thread sealant to hose fittings (both ends).
Tools Needed
• None
Hose fitting
5
Installation Instructions
Step 3
• Place dust cap and dust plug loop over hose.
• CAUTION: Never back off an installed pipe fitting to achieve proper alignment.
Loosening installed pipe fittings will corrupt the seal and contribute to leakage and
failure.
• Screw hand-tight hose fittings with thread sealant applied into the quick disconnect
fittings (male with cap and female with plug).
• Wrench-tighten the fitting to 1.5-3.0 Turns Past Finger Tight position. Properly
assembled fittings total thread engagement should be 3.5-6 turns.
Tools Needed
• Adjustable Wrenches
Male quick disconnect fitting
Hose
Dust plug
Dust cap
Female quick disconnect fitting
6
Operation
Warm up procedure
1. Attach hose to unit by connecting quick disconnect fittings as shown.
2. Follow start procedure from owner’s manual.
3. Allow unit to warm up.
4. Shut off engine.
5. Disconnect hose.
6. Position dust cap and plug in quick disconnect fittings to prevent contamination.
7. Attach implement.
7
Limited Warranty
Dear Valued Customer:
The Brave product you just purchased is built with the finest material and craftsmanship. Use this product properly and enjoy the benefits from
its high performance. By purchasing a Brave product, you show a desire for quality and durability. Like all mechanical equipment this unit
requires a due amount of care. Treat this unit like the high quality piece of machinery it is. Neglect and improper handling may impair its
performance.
Thoroughly read the instructions and understand the operation before using your product. Always contact Brave Product Support at
1-800-350-8739 prior to having any service or warranty work performed, as some services performed by parties other than Brave approved
service centers may void this warranty. This limited warranty is in lieu of any other warranty expressed or implied, written or oral and Brave
assumes no other responsibility or liability outside that expressed within this limited warranty.
Limited Warranty for Brave and Brave Pro Hydra Buddy Models:
1158284
1158285
1158286
1158287
1158288
1158289
1158290
1158292
1158293
Consumer Warranty Period
Commercial Warranty Period
Weldments
2 years from date of purchase by user
2 year from date of purchase by user
Valves and Pumps
2 years from date of purchase by user
1 year from date of purchase by user
Wear Parts
In addition to the normal warranty, Brave shall warrant some normal wear items from defects in material or
workmanship for a period of 30 days from the date of purchase by user. Normal wear items covered under
this warranty are limited to: clamps, couplers, filters, mounts, hoses, hardware. Routine maintenance items
such as lubricants, clutch adjustments, tune ups are not covered under warranty.
Engines
The engine warranty is covered under the terms and conditions as outlined by the engine manufactures
warranty contained herein and is the sole responsibility of the engine manufacturer. Normal engine
maintenance such as spark plugs, oil changes, air filters, adjustments, fuel system cleaning and obstruction
due to build up is not covered by this Brave limited warranty.
“Consumer use” means personal residential household use by a consumer. “Commercial use” means all other uses, including, but not limited to,
use for commercial, income producing or rental purposes or when purchased by a business.
This limited warranty applies to the original purchaser of the equipment (verification of purchase, in the form of a receipt, is the responsibility
of the buyer), is non-transferable, and covers parts and labor. Parts will be replaced or repaired at no charge, except when the equipment has
failed due to lack of proper maintenance. If a part is no longer available, the part may be replaced with a similar part of equal function. Any
misuse, abuse, alteration or improper installation or operations will void warranty. Determining whether a part is to be replaced or repaired is
the sole decision of Brave. Brave will not provide for replacement of complete products due to defective parts. Any costs incurred due to
replacement or repair of items outside of a Brave approved facility is the responsibility of the buyer and not covered under warranty.
Transportation costs to and from service center and/or service calls are the responsibility of the customer.
This limited warranty specifically excludes the following; failure of parts due to damage caused by accident, fire, flood, windstorm, acts of
God, applications not approved by Brave in writing, corrosion caused by chemicals, use of replacement parts which do not conform to
manufacturer’s specifications, damage related to rodent and/or insect infestation and damage caused by vandalism. Additional exclusions: loss
of running time, inconvenience, loss of income, or loss of use, including any implied warranty of merchantability of fitness for a specific use.
Also, outdoor power equipment needs periodic parts and service to perform well, and this limited warranty does not cover instances when
normal use has exhausted the life of a component or the engine.
This limited warranty does not cover any personal injury or damage to surrounding property caused by failure of any part, misuse or inability to
use the product. Alteration of the product, including safety features, shall void this limited warranty.
Repair or replacement of parts does not extend the warranty period. This limited warranty gives you specific legal rights. You may also have
other rights that vary by state.
Please have model number, item number and serial number on hand prior to making a warranty claim or inquiry.
8
20195 S. Diamond Lake Rd, Ste 100
Rogers, MN 55374
1-800-350-8739
Loading...