BraunAbility HAL2, HAL3 Instructions For Fitting And Use

HAND ACTUATED LOCKABLES
User Manual
EN Instructions for tting and use
2
HAL2, HAL3
Thank you for choosing
Hand Actuated Lockables from BraunAbility!
The following manual is an important part of the product, providing you with information on how to achieve maximum performance and safe operation. Keep the manual in a safe place so that you can refer to it when necessary.
If you have any questions about your equipment, please contact us.
Once again, thank you for placing your condence in our products!
Safe vehicle adaptation solutions
For your safety BraunAbility products are
designed and tested according to current
directives and standards.
Safety information
Limitation of use
4
Fit and use
Fitting the Hand Actuated Lockable (HAL) to the seat leg
6
Adjusting HAL setting to the rail
8
Operating HAL
10
After care
Equipment storage and maintenance
12
Warranty
12
HAL2, HAL3
3
EN
Index
“Declaration of conformity” at the end of the manual.
4
HAL2, HAL3
Safety information
Limitation of use
HAL2, HAL3
5
HAL2 - 2 Fixing Studs
HAL3 - 3 Fixing Studs
EN
Fit and use
6
HAL2, HAL3
Fit and use
Fitting the Hand Actuated Lockable (HAL) to the seat leg
Note: Two removable seat xtures are normally required for each seat. It is important that the seat legs are set to the identical rail width where the seat is to be tted. Both HAL need to be aligned parallel to each other in the rail.
1. First, remove all M10 nyloc nuts and washers from sliding stud assemblies with a 17mm wrench (Fig. 1).
2. Ensure the seat is placed facing towards the front of the vehicle. Fit sliding studs through the seat leg bracket holes as shown above. Position both seat legs at approximately 5mm (1/4”) from the front of the handle, ensuring alignment (Fig. 2).
3. Replace all washers and nuts and loosely fasten with a 17mm wrench (Fig. 3). Finally tighten the M10 nyloc nuts with a torque wrench to a recommended torque of : 35-40Nm (18-22lb.ft)
HAL2, HAL3
7
M10 Nyloc Nut
Sliding Stud
Seat Leg
Front of Vehicle
17mm wrench
Figure 1 Figure 2 Figure 3
M10 Nyloc Nut
WARNING
In 3 stud version, the rear most xing MUST NOT be used in isolation. If it is intended that the seat should face the rear, please contact BraunAbility.
EN
Fit and use
17mm wrench
8
HAL2, HAL3
Fit and use
Adjusting HAL setting to the rail
HAL lockable comes with variable adjustable setting to accommodate different rail proles and
thicknesses. Each setting relates to a different thickness depth.
Setting 1: Thinner Rail Setting 2: Standard Rail Setting 3: Thicker Rail
1. Once HAL has been tted to the seat leg, check that the lockables are on the right setting to
t the rail in your vehicle.
2. Place the seat in the rail with HAL unlocked (Fig. 4).
3. Try and lock the seat by pushing the handle forward to the locked position (Fig. 5):
A. The handle locks smoothly and the seat doesn’t rattle; HAL is set correctly. B. The handle is dif cult to push forward; looking from the front, adjust HAL by inserting a
3mm allen key and rotating half turn clockwise . Once this is done try locking HAL again. (Repeat operation as necessary). C. The handle locks too easily and rattles; looking from the front, adjust HAL by inserting a 3mm allen key and rotating half turn anti-clockwise. Once this is done try locking HAL again. (Repeat operation as necessary).
IMPORTANT: Tighten by hand only. Do not use tools of any kind.
HAL2, HAL3
9
EN
Fit and use
Figure 4
Unlock
Figure 5
Setting
Adjustment
Lock
10
HAL2, HAL3
Fit and use
Operating HAL
1. Before locating the seat into the rail, unlock HAL, by pressing the silver trigger (Fig 6) and then pull the handle fully back (Fig 7).
2. To locate the seat in the rail, align both HAL wheels into the rail, tilt the seat backwards slightly and wheel it along the rail to the right location. Once this is found, lower the seat into the rail gently push it forwards or backwards until it is located into the rail.
3. To lock the seat into the rail, push the handle forward to the upright position (Fig 8) until you hear it click.
Anti-tamper device
The anti-tamper device, which is supplied with HAL, is an optional accessory.
1. Should you choose to use this device during transportation, just clip it on to
the silver trigger, making sure it is safely tted (Fig 9).
2. To remove the device, simply push it sideways to release the silver trigger. Stow away securely.
Removing seat from rail
1. To release the seat from the rail, unlock HAL, by pushing handle forward while pressing the silver trigger (Fig 6), then pulling the handle fully back (Fig 7).
2. Tip the seat backwards and remove from the rail.
Figure 6 Figure 7
HAL2, HAL3
11
EN
Fit and use
Figure 8
Silver
Tri gge r
Anti-damper
device
Figure 9
12
HAL2, HAL3
After care
Equipment storage and maintenance
Regularly inspect HAL for damage, wear or malfunction. If any problems are identied replace it immediately.
Warranty
BraunAbility products are extensively tested using BraunAbility anchorage systems, and our full warranty normally only applies to BraunAbility equipment when used with BraunAbility branded anchorages or as instructed. BraunAbility have also participated in test programs with other manufacturers anchorage products and will support warranty on the BraunAbility products when used in conjunction with such jointly tested systems.
For further details on specic applications please contact the Sales Of ce. In other situations, using
BraunAbility products, for which BraunAbility has not participated in a joint test program, a limited BraunAbility warranty will apply.
Declaration of conformity
Manufacturer /
BraunAbility UK Ltd. Unwin House The Horseshoe Coat Road Martock, Somerset, TA12 6EY UK
Phone: +44 1935 827740 E-mail: sales.uk@braunability.eu www.braunability.eu
Declares that the products /
HAL2, HAL3
Conforms to following directives standards and regulations /
2001/85/EC Annexe VII Paragraphs 3.8.2.8 & 3.8.2.9 76/115/EEC R.14.07 R.107.06 BS EN 1789:2007+A2:2014
BraunAbility, Martock, 23rd April 2019
Rob Butcher Director of Engineering
Accredited by URS as testing laboratory in accordance with ISO/IEC 17025:2005
Accredited by URS as testing laboratory in accordance with ISO/IEC 17025:2005
Illustrations, descriptions and specications in the user manual are based on current product information.
Illustrations, descriptions and specications in the user manual are based on current product information.
BraunAbility UK Ltd reserves the right to make alterations without previous notice.
BraunAbility UK Ltd reserves the right to make alterations without previous notice.
Quality system certied in accordance with ISO 9001:2008
Quality system certied in accordance with ISO 9001:2008
© 2019 BraunAbility UK Ltd
© 2019 BraunAbility UK Ltd
BraunAbility UK Ltd
BraunAbility UK Ltd
Unwin House
Unwin House
The Horseshoe, Coat Road
The Horseshoe, Coat Road
Martock, Somerset, TA12 6EY
Martock, Somerset, TA12 6EY
UK
UK
Phone: +44 1935 827 740
Phone: +44 1935 827 740
E-mail: info@braunability.eu
E-mail: info@braunability.eu
www.braunability.eu
www.braunability.eu
UI1911F
Loading...