Braun 5737, 5885 User Manual

0 (0)
Braun 5737, 5885 User Manual

Contour Series

5885

washable

 

stop

start

 

 

 

Type 5737

Modèle 5737

Modelo 5737

www.braun.com/register

English

4

Thank you for purchasing a Braun product.

 

 

We hope you are completely satisfied with

Français

9

your new Braun shaver.

 

 

 

If you have any questions, please call:

Español

14

US residents

1-800-BRAUN-11

 

 

 

1-800-272-8611

 

 

Canadian residents

1-800-387-6657

 

 

Merci d’avoir fait l’achat d’un produit Braun.

 

 

Nous espérons que vous serez pleinement

 

 

satisfait de votre nouveau rasoir Braun.

 

 

Si vous avez des questions, veuillez appeler

 

 

Braun Canada :

1-800-387-6657

Gracias por haber comprado un producto Braun.

Esperamos que quede completamente satisfecho con su nueva afeitadora Braun. Si tiene alguna duda, por favor llame al:

01(800) 508-5800

5-737-450/00/III-07 USA / CDN / MEX Printed in Germany Imprimé en Allemagne Impreso en Alemania

1

 

 

 

 

 

stop

 

 

 

 

start

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

3

 

 

 

 

 

 

 

 

 

washable

 

 

 

 

 

 

 

stop

4

 

 

 

start

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

7

 

 

 

 

 

 

8

 

 

 

 

 

 

9

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

off

 

 

 

 

oil

 

 

English

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using this appliance.

When disconnected, the hand-held part of this shaving appliance may be cleaned under water.

DANGER

To reduce the risk of electric shock:

1.Use only in dry condition.

2.Do not submerge in water.

3.Do not reach for an appliance that has fallen into water. Unplug immediately.

4.Do not use while bathing or in a shower.

5.Do not place, store or charge the appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.

6.Except when charging, always unplug this appliance from the electrical outlet immediately after using.

7.Unplug this appliance before cleaning.

8.This appliance is provided with a special cord set with integrated Safety Extra Low Voltage power supply. Do not exchange or manipulate any part of it.

9.Do not use an extension cord with this appliance.

FOR HOUSEHOLD USE ONLY

4

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

1.Close supervision is necessary when this appliance is used by, on, or near children or invalids.

2.Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

3.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or if the power supply has been dropped into water. Return the appliance to a service center for examination and repair.

4.Keep the cord away from heated surfaces.

5.Never drop or insert any object into any opening.

6.Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

7.Do not use this appliance with a damaged or broken foil, as serious skin injuries may occur.

8.Always attach plug to appliance first, then to outlet.

To disconnect, turn all controls to «off», then remove plug from outlet.

9.When plugging to an electrical outlet outside the USA, use a plug adapter to match the outlet’s pin configuration.

SAVE THIS INSTRUCTIONS

5

Description

1 Shaver foil

2 Cutter block

3 Release button

4 On/off switch («start/stop»)

5 Long hair trimmer

6 Charging lights (green)

7 Low-charge light (red)

8 Replacement light for shaving parts

9 Reset button

10 Special cord set

Charging

The best environmental temperature for charging is between 60 °F to 95 °F/15 °C and 35 °C.

Using the special cord set, connect the shaver/charging stand to an electrical outlet with the motor switched off.

When charging for the first time, leave the shaver to charge continuously for 4 hours.

Once the shaver is completely charged, discharge the shaver through normal use. Then recharge to full capacity. Subsequent charges will take about 1 hour.

A full charge provides up to 50 minutes of cordless shaving time depending on your beard growth.

Maximum battery capacity will only be reached after several charging/discharging cycles.

If the rechargeable batteries are discharged, you may also shave by connecting the shaver to an electrical outlet via the special cord set.

Charging lights

The 3 charging lights (6) blink to indicate the charging level by thirds. When fully charged, all 3 charging lights shine permanently.

Low-charge light

The red low-charge light flashes when the battery capacity has dropped below 20%, provided the shaver is switched on.

The re-maining capacity will then be sufficient for 2 to 3 shaves.

Shaving

Turn on the shaver («start»):

The pivoting cutting system automatically adjusts to every contour of your face.

Trimmer:

When the long hair trimmer is activated, it allows the controlled trimming of moustache or sideburns.

Tips for the perfect shave

It can take up to 14-21 days for your beard to adjust to the new shaving system.

Shave before washing your face or taking a shower, as skin tends to swell after washing.

The drier the skin, the closer the shaving results will be.

Hold the shaver at right angles (90°) to the skin. Stretch the skin and shave against the direction of beard growth.

To maintain 100% shaving performance, replace the shaver foil and cutter block, when the replacement light (8) comes on (after about 18 months), or when the shaving parts are worn.

Cleaning

The hand-held unit should be detached from the power supply cord before cleaning. The shaver should not be used until it has dried.

Regular cleaning ensures better shaving performance. Rinsing the shaving head after each shave under running water is an easy and fast way to keep it clean:

Switch the shaver on (cordless) and rinse the shaving head under hot running water. A natural based soap may also be used provided it contains no particles or abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.

Next, switch off the shaver, remove the shaver foil and the cutter block. Then leave the disassembled shaving parts to dry.

6

Loading...
+ 12 hidden pages