Page 1
Branick Industries, Inc. • 4245 Main Ave • Fargo, North Dakota 58103
P/N: 81-0224B
REV081717
MODEL S-FLL
Tire Repair
Station
Installation, Operation
and Repair Parts
Information
Page 2
1
TABLE OF CONTENTS
________________________________________________________________________
SAFETY INSTRUCTIONS 1
DEFINITIONS 1
INSTALLATION INSTRUCTIONS 2
OPERATING INSTRUCTIONS 2
MAINTENANCE INSTRUCTIONS 2
REPAIR PARTS 3
WARRANTY 7
SAFETY INSTRUCTIONS
________________________________________________________________________
▪ NEVER allow unauthorized personnel to operate this product.
▪ NEVER use this product for anything other than its intended use.
▪ THOROUGHLY train new employees in the proper use and care of this product.
▪ PROHIBIT unauthorized personnel from being in shop area while this product is in use.
DEFINITIONS
________________________________________________________________________
▪ CAUTION: Indicates a potentially hazardous situation, which if not avoided, may result in damage to
property or minor personal injury.
▪ HAZARD: A source of potential injury to a person.
▪ MAINTENANCE: Those actions that preserve the correct and proper conditions under which the
machine shall be used. This may include adjustment, replacement of wear items, lubrication and
cleaning, but not modifications or repair of damage.
▪ MAY: This word is understood to be permissive.
▪ MUST: This word is understood to be mandatory.
▪ OPERATION: The correct and proper use of the machine as described in this manual.
▪ SAFETY ALERT SYMBOL: A symbol that indicates a potential personal safety hazard. It is
composed of an equilateral triangle surrounding an exclamation point.
▪ SHALL: This word is understood to be mandatory.
▪ SHOULD: This word is understood to be advisory.
▪ WARNING: Indicates a potentially hazardous situation, which if not avoided, may result in death or
serious personal injury.
Page 3
2
INSTALLATION __________________________________________________________
1) Remove wrappings and barrier material from air valves.
2) Place tire ramp in center of front and hook over angle base.
OPERATION _____________________________________________________________
1) Roll tire onto support rollers.
2) Slide hooks up to proper level for tire size, hooks should slope slightly upward toward tire.
3) Insert fast pins in arms then swing hooks into tire beads.
4) Step on spread valve to spread tire, valve will hold tire at desired spread width.
5) To release spread step on valve marked, “release” when hooks are fully relaxed swing hooks out of tire.
6) The spreader will handle tires from 7.50-10 four-ply through 16.00-24.5 twenty-ply. Maximum spread is 16
inches.
MAINTENANCE __________________________________________________________
Monthly: Oil the pivot points of hook pivot and arm pivot through oil hole in sleeves. The vertical posts may
be waxed to make hook assemblies slide easier. Oil the tire support roller shafts at brackets. Oil pivot
points at piston rod and cylinder end connections.
Every Six Months: Remove air cylinder cover plate and remove piston and rod. Clean thoroughly.
Reassemble and add ½ cup of clean oil in rear of cylinder through pipe tee on end of cylinder.
CAUTION
Before using this product, read and fully understand the operating
instructions and all decals on the product. This is necessary to
prevent injury to the operator and damage to the product.
Use this product only for lifting, spreading and repairing tire
casings. Do not use this product for any other purpose.
Keep fingers and hands clear of spread hooks during tire spread.
Do not use this product if it is visibly worn, distorted or damaged.
Always wear appropriate eye protection.
WARNING
Keep feet clear of the tire ramp and scissor arms when raising and
lowering spreader platform.
All personnel must be clear of the tire lift area during operation.
Page 4
3
REPAIR PARTS __________________________________________________________
Page 5
4
ITEM
QTY
PART NO.
DESCRIPTION
1 2 900-189
HOOK ASSEMBLY (INCLUDES FASTPIN)
2 2 061-179
5/16 X 3-1/2 FASTPIN
3 1 110-011
SPRING
4 1 101-113
TIRE RAMP
5 1 900-184
BASE ASSEMBLY
6 5 055-154
3/8 NC HEX LOCK NUT
7 1 03-0036
LINK PIVOT
8 1 835-020
FOOT PEDAL GUARD
9 4 028-005
7/16-14 X 3/4 HHCS
10 2 950-553
SHORT LINK
11 2 055-058
1/2 NC HEX LOCK NUT
12 1 096-155
1/4 NPT M 1/4 NPT F TEE
13 1 50-0027
3/8 X 1 SHOULDER BOLT
14 1 096-004
1/4 OIL PLUG
15 2 028-025
1/2-13 X 1-1/2 HHCS
16 1 900-193
AIR HOSE
17 1 950-194
CYLINDER
18 4 108-015
3/8 SAE FLAT WASHER
19 1 932-001
IN-LINE FILTER
20 1 096-107
PIPE COUPLING FITTING
21 1 096-013
1/4 NPT NIPPLE FITTING
22 2 096-038
1/4 NPT STREET ELBOW
23 1 61-0028
QUAD RING SEAL
24 1 950-195
PISTON & ROD WELDMENT
25 1 041-202
ROD SEAL
26 1 098-327
COVER PLATE
27 1 006-004
PLUG
28 1 11-0065A
NYLON WEAR STRIP
29 2 055-160
1/4 NC HEX LOCK NUT
30 1 885-035
MUFFLER
31 1 190-277
3 WAY TREADLE VALVE
32 2 028-390
1/4-20 X 1 1/4 FHM SCREW
This page intentionally left blank.
Page 6
5
This page intentionally left blank.
Page 7
6
COMMERCIAL WARRANTY
This product is warranted by BRANICK INDUSTRIES, INC. to the original user-owner against defective
materials or workmanship for a period of one year from the date of shipment. During the warranty period, at
the discretion of Branick management, if the product is found to be defective, it will be repaired or replaced
without charge. For service, contact Branick (800-437-4394) to obtain an RMA. Any product shipped to
Branick must have an RMA and proof of original shipment date. The repaired or replacement product will be
returned with transportation charges prepaid by Branick.
This warranty does not cover defects in the product caused by ordinary wear and tear, abuse, misuse,
overloading, accident (including shipping damage), improper maintenance, alteration, or any other cause not
the result of defective materials or workmanship.
REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCT UNDER THIS
WARRANTY. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANT ABILITY OR ANY IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OF THIS PRODUCT. BRANICK INDUSTRIES, INC. SHALL NOT BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES.
BRANICK INDUSTRIES, INC. reserves the right to make changes in the design or construction of our
products without obligation to incorporate such changes in products already sold and without notice.
Service parts and regular repair service are available from authorized distributors of Branick products, or from:
BRANICK INDUSTRIES, INC.
4245 Main Ave.
Fargo, North Dakota 58103
Toll Free: 800-437-4394
www.branick.com
© Copyright 2018 by Branick Industries, Inc. Printed in U.S.A.
Loading...