Page 1
Rev08112017 P/N: 81-0277B
Installation, Operation
and Repair Parts
Information
MODEL AH/RI-R
Adjustable Height
Repair Inspector
THIS PAGE INTENTIONALLY LEFT BLANK
Page 2
1
INSTALLATION INSTRUCTIONS________________________________________________
1. Unpack and remove the unit from the shipping carton.
2. Inspect the unit for any visible damage.
3. Connect a 1/2" air line to the filter inlet.
4. Plug the light cord into a standard 110 V outlet.
5. Check lubricator to ensure it has oil.
OPERATING INSTRUCTIONS__________________________________________________
1. Roll tire up the ramp onto the traction rollers.
2. Using the Lift control, raise the tire to the desired working level.
CAUTION: Lifting speed is preset by means of a flow control at the top of the lift cylinder. Any adjustment can
cause the lift to raise to quickly for safe operation.
3. Place the spread hooks between the tire beads.
4. Adjust spread hook height by grasping the pivot bar and pull the lock pins out. Slide spread hooks up /
down so the spring pin is centered on desired positioning hole and release spring pins.
5. Using the Spread control, spread tire to allow visibility into tire interior.
NOTE: If the tire is lifted off the rollers when spread, release spread and move spread hooks to a lower
position.
6. Position the light inside of the tire and rotate tire for inspection using the foot operated Rotate control.
7. The speed of rotation can be controlled by varying the pressure on the foot control.
8. If a repair is needed:
a. Stop rotation with the section needing repair at the bottom (between rollers).
b. Invert tread using the Invert control and make repairs.
CAUTION: Do not invert tire with spread hooks disengaged from beads or while rotating tire.
9. To lower tire, disengage spread hooks and push down on Lift control. Ramp will swing down into position
to roll tire off machine.
CAUTION: Keep feet clear of machine while lowering.
MAINTENANCE______________________________________________________________
1. Disconnect air supply before servicing machine.
2. The vertical posts on the spread hook assembly should be waxed periodically.
3. Once a month pour about 1/4 cup of 10 or 20 SAE motor oil through the plug in the pipe tee on the
spread cylinder and through the plug in the cover plate on the invert cylinder.
Page 3
2
REPAIR PARTS_____________________________________________________________
Page 4
3
MODEL AH/RI
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
1
268-565
4
Tube
39
950-553
1
Short Link
2
061-005
4
Spring Pin
40
028-025
2
Capscrew
3
859-004
1
Ramp
41
900-187
1
Spread Cylinder (See page 8)
4 42
D20-007
1
Airline
5
149-321
1
Shaft
43
822-009
1
Clevis
6
841-017
1
Housing
44
039-043
2
Bushing
7
108-056
10
Lockwasher
45
096-342
6
Male Elbow
8
028-159
2
Capscrew
46
885-035
2
Muffler
9
834-083
1
Base Frame
47
039-008
6
Reducer Bushing
10
039-080
8
Bushing
48
190-222
2
Flow Control
11
874-012
1
Yoke
49
096-221
1
Close Nipple
12
055-160
6
Hex Locknut
50
028-148
12
Tapping Screw
13
108-110
6
Washer
51
098-126
2
Chain Cover
14
028-047
8
1/2 NC x 1 3/4 HHCS
52
098-125
1
Top Cover
15
564-028
1
Piston Rod Lock
53
096-048
1
Swivel Elbow
16
104-135
4
Shaft
54
030-036
1
Lift Cylinder
17
104-136
1
Shaft
55
190-066
2
Valve
18
055-154
5
Hex Locknut
56
096-004
2
Pipe Plug
19
110-011
1
Spring
57
055-057
8
Hex Nut
20
03-0036
1
Link Pivot
58
028-161
8
Rd. Hd. Mach. Screw
21
028-041
2
Capscrew
59
096-038
1
Street Elbow
22
111-487
1
Bracket
60
885-036
1
Speed Control Muffler
23 61
096-341
1
Union Elbow
24 62
646-186
1
Airline
25
039-007
4
Machine Bushing
63
879-018
1
Valve Post
26
055-103
8
Flange Locknut
64
646-185
3
Airline
27
107-020
4
Bearing
65
096-339
1
Union Tee
28
028-021
8
Capscrew
66
096-340
3
Male Connector
29
863-011
2
Traction Roller
67
646-187
1
Airline
30 68
028-207
1
Nylon Set Screw
31 - 2
Spread Arm (See page 9)
69
268-575
1
Airline
32
40-0090
1
LED Lamp
70
028-010
4
Capscrew
33 - 71
018-033
1
Filter Assembly (See page 7)
34
006-014
4
Caplug
72 35
028-280
1
Capscrew
73
643-199
1
Invert Cylinder Option (See page 6)
36
878-040
1
Light Bracket
74
643-201
1
Reversible Option (See page 7)
37
055-058
2
Hex Locknut
75
108-008
1
1/4 Int. Tooth Lockwasher
38
950-553
1
Reinforced Short Link
76
028-210
1
1/4 NC x 5/8 HHCS
77
05-0005
1
Seal Kit for Lift Cylinder (not shown)
Page 5
4
INVERT COMPONENTS (643-199)
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
1
877-006
1
Piston Rod
12
108-032
1
Cup Washer
2
098-327
1
Cover Plate
13
041-015
1
Piston Cup
3
110-003
1
Spring
14
051-023
1
Piston
4
055-154
1
Hex Locknut
15
096-004
1
Pipe Plug
5
108-015
1
Washer
16
190-066
1
Valve
6
028-022
1
Capscrew
17
055-057
4
Hex Nut
7
096-342
3
Male Elbow
18
646-199
1
Airline
8
028-280
3
Capscrew
19
885-035
1
Muffler
9
828-013
1
Cylinder
20
646-185
2
Airline
10
028-239
1
Capscrew
21
11
167-240
1
14 Mil Gasket
22
028-161
4
Rd. Hd. Mach. Screw
Page 6
5
REVERSIBLE REVOLVE COMPONENTS (643-201)
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
1
251-037
1
Key
28
268-573
1
Airline
2
032-007
1
Gear Reducer
29
018-033
1
Filter Assembly
3
028-210
4
Capscrew
30 4
108-008
4
Lock Washer
31
028-010
2
Capscrew
5 32 6
228-047
1
Sprocket
33 7
034-041
1
Flex Coupler
34
055-160
6
Hex Lock Nut
8
186-073
1
Spacer
35 9
108-123
4
Washer
36
096-221
1
Close Nipple
10
055-145
4
Lock Nut
37
096-249
1
Tee
11
028-014
4
Capscrew
38
096-340
1
Male Connector
12
190-241
1
Treadle Valve
39
023-007
1
Gauge
13
50-0168
4
Rd. Hd. Mach. Screw
40
096-075
2
Street Elbow
14
980-115
2
Conduit Connector
41
190-222
1
Flow Control
15
096-342
4
Male Elbow
42
096-354
2
Male Connector
16
055-057
4
Hex Nut
43
251-026
2
Key
17
885-035
2
Muffler
44
228-048
2
Sprocket
18
259-040
1
Air Motor
45
066-050
1
Chain
19
268-017
3
Airline
46
062-045
1
Offset Link (Not shown)
20
980-250
1
Conduit
47
096-346
2
Male Elbow
21
096-107
3
Straight Union
48
028-077
4
Capscrew
22
268-572
2
Airline
49
190-240
1
Pilot Valve
23
096-025
4
Swivel Elbow
50
940-040
1
Hose
24
096-058
3
Close Nipple
51
878-041
1
Muffler Bracket
25
096-070
1
Tee
52
885-081
1
Muffler
26
940-039
1
Hose
53
940-041
2
Hose
27
268-574
1
Airline
54
835-016
1
Foot Treadle Guard (Not shown)
Page 7
6
SPREAD CYLINDER (900-187)
SPREAD ARM COMPONENTS
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
1
950-194
1
Cylinder
6
098-327
1
Cover Plate
2
028-005
4
7/16 NC x 3/4 HHCS
7
006-004
1
Caplug
3
041-204
1
Block Vee-Seal
8
096-004
1
Pipe Plug
4
950-195
1
Piston and Rod
9
096-155
1
Pipe Tee
5
041-202
1
Rod Seal
10
096-221
1
Close Nipple
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
ITEM
NO.
PART
NO.
NO.
REQ’D
DESCRIPTION
1
839-026
1
Spread Hook
9
055-156
2
Hex Cap Nut
2
108-044
2
1/2" Flat Washer
10
104-079
2
Spread Roller Shaft
3
11.0025
1
Bead Roller
11
11.0024
2
Spread Roller
4
863-004
1
Roller Weldment
12
055-072
2
Hex Cap Nut
5
110-025
1
Bead Roller Spring
13
028-155
2
10-24 Pan Hd. Screw x 5/8
6
446-071
2
Sleeve
14
061-153
2
Latch Pin
7
061-032
2
1/8 x 3/4 Spring Pin
15
110-018
2
Latch Spring
8
104-082
1
Shaft
Page 8
7
COMMERCIAL WARRANTY
This product is warranted by BRANICK INDUSTRIES, INC. to the original user-owner against defective materials
or workmanship for a period of one year from the date of shipment. During the warranty period, at the discretion of
Branick management, if the product is found to be defective, it will be repaired or replaced without charge. For
service, contact Branick (800-437-4394) to obtain an RMA. Any product shipped to Branick must have an RMA
and proof of original shipment date. The repaired or replacement product will be returned with transportation
charges prepaid by Branick.
This warranty does not cover defects in the product caused by ordinary wear and tear, abuse, misuse,
overloading, accident (including shipping damage), improper maintenance, alteration, or any other cause not the
result of defective materials or workmanship.
REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCT UNDER THIS
WARRANTY. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANT ABILITY OR ANY IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OF THIS PRODUCT. BRANICK INDUSTRIES, INC. SHALL NOT BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES.
BRANICK INDUSTRIES, INC. reserves the right to make changes in the design or construction of our products
without obligation to incorporate such changes in products already sold and without notice.
Service parts and regular repair service are available from authorized distributors of Branick products, or from:
BRANICK INDUSTRIES, INC.
4245 Main Ave.
Fargo, North Dakota 58103
Toll Free: 800-437-4394
www.branick.com
© Copyright 2018 by Branick Industries, Inc. Printed in U.S.A.
Loading...