Page 1
Menu Functions
Gain
Red Gain
Blue Gain
Detail
Shutter Speed
White Balance
Gamma
Master Pedestal
Output Standard
Iris Range
Pan Speed
Tilt Speed
Reverse Pan/Tilt
Zoom Reverse
Focus Reverse
Head Select
Change Head ID
Reset ALL to #1
Infra Red Mode
Power Up Memory
Store Position
Go To Position
Digital Zoom
Remote Relay
Auto Focus
Zoom Limit
Adjusts the Gain from -3dB to +18dB in 3dB steps.
Requires White Balance to be set to Manual
Requires White Balance to be set to Manual
Adjusts the detail level from 0 to 15. Normal setting is around 5.
Adjusts the shutter speed from 1/2sec to 1/10,000 sec.
Includes BARS if available
There are 3 levels of gamma available.
Not available for the BE_HD10
SD or HD in 8 different standards
Set to 18 for BE_HD10 or 255 for broadcast lenses
High or Low
High or Low
Cycles through the 4 direction combinations
Reverses the direction of the zoom control
Reverses the direction of the focus control
Selects control of another remote head 1-99
Re-assigns the ID of the current head
Re-sets all connected heads to ID #1
Toggles the IR mode on or Off
Set/Clear. This feature can only be used with a
Protocol Converter
Setting the memory will store the current Zoom and Focus positions in
Protocol Converter
the
and reset them every time it powers up.
Stores the current position head and camera as a preset position 1-99
Recalls the previously set positions 1-99
Digital Zoom On/Off
Commands a remote relay On/Off
Auto Focus On/Off
Sets the current zoom position as the zoom in limit.
.
Zeroing the controls
Should the Pan, Tilt or Zoom controls appear to be off-centre (sometimes this will induce drift) the
controls can be electrically re-centred.
Whilst the AUX LED is flashing at power-up, push the AUX button.
Specifications
Power: 12v, 200mA
Dimensions: W.165mm, D.90mm, H.35mm
Output: RS485 or RS232c
Max Cable Length:
1km
(with RS485 device or
protocol converter)
David Bradley Engineering Ltd - www.bradeng.com
Page 2
Micro Controller
Operating Instructions
Connections
There is just 1 XLR4 connector recessed into one end of the unit. This socket inputs power via 2
pins and outputs data on the other 2 pins. A dedicated ‘Y’ cable is supplied to break out this
socket into industry standard, individual XLR connectors.
Pin 1 - GND
Pin 2 - Data A (RS485)
Pin 3 - Data B (RS485)
Pin 4 - Power In
Primary Functions
The primary functions are accessed directly via the dedicated knobs and buttons. The LCD
display will show the values as they are changed.
Contents
Introduction Page 2
Connetions Page 3
Primary Functions Page 3
Menu Functions Page 4
Wide Angle Lens Page 4
Specifications Page 4
Micro Controller
The
Almost all Bradley Engineering functions can be accessed from this tiny controller via the LCD
menu and the dedicated knobs and buttons.
Bradley Engineering
Units 14 - 20 Setley Ridge Vineyard
Lymington Road
Brockenhurst
Hampshire
SO42 7UF
UK
is a very small but powerfull controller for cameras and remote heads.
Pan & Tilt
Zoom
Focus
Iris
Rec/Stop
Assign
Aux
The thumb operated joystick on the right controls pan and tilt. Touching down
this joystick puts the remote head into its top speed for fast repositioning.
Releasing the touch down reverts the head to the previous speed setting. Both
axes can be reversed via the LCD menu.
The left side joystick moves only forwards and back and controls the
zoom. The direction can be reversed via the LCD menu.
The focus control is illuminated blue and on the extreme left of the console. It
can be operated either from the top of the panel or with the knurled wheel in
the rece ssed end plate. The direction can be reversed via the LCD menu.
Depressing this knob once changes the focus to fine or coarse control. When
the focus is in coarse mode the blue LED is bright.
Rotating the Iris knob adjusts the iris setting from F1.6 to F28. The setting will
be shown briefly in the LCD display as it is adjusted.
The Record / Stop button illuminates Red when a record command is sent.
This is a touch down knob. When touched down and simultaneously rotated
menu
the
touch down and the knob now controls the value of the setting.
The Aux button is used in conjunction with the
selected with the knob. The display indicates when this is required.
page is changed. When the desired page is displayed release the
menu
to send the value
Tel: +44 1590 622440
Web: www.bradeng.com
Loading...