Bradley Corporation 780-1830, 780-1836, 780-2436, 780-2460 User Manual
Mirror with angle frame, welded corners and
theft‑resistant mounting:
Standard Model 780‑1830 (18" x 30") Bradex
Standard Model 780‑1836 (18" x 36") Bradex
Standard Model 780‑2436 (24" x 36") Bradex
Standard Model 780‑2460 (24" x 60") Bradex
®
®
®
®
Model 780‑XXXX (Specify width and height)
Product Materials
FRAME: one-piece roll-formed stain less steel, ¾" x ¾" angle with corners welded,
ground and polished smooth to a satin finish. Double strength continuous integral
stiffener on all sides for added strength. Bevel on front of angle secures frame flush
against mirror.
BACK: galvanized steel, secured to frame with concealed screws, equipped with integral
horizontal hanging brackets.
MIRROR: first quality ¼" float glass, thermosetting infrared cured-paint backing with
Poly-Glaze protective finish. Manufactured in accordance with ASTM C 1036 and ASTM
C 1503. All edges protected by shock-absorbing, neoprene tubing. The back of the
mirror is protected by a sheet of ¼" extruded polystyrene, which is placed between the
mirror and the galvanized steel.
WALL HANGER: 18 gauge cold rolled steel, all welded construction to form rigid
template.
Optional Features
Features Suffix
¼" tempered glass mirror in lieu of polished float glass mirror* -2
Laminate glass -3
Highly polished No. 8 architectural finish, 20 gauge stainless steel in lieu of
polished float glass mirror
Bright annealed 20 gauge stainless steel in lieu of polished float glass mirror -5
* Either the Length (L) or the Width (W) must be greater than 25".
®
Plexiglas
An inherent characteristic of a manufacturing process for tempered glass is distortion
which may vary from mirror to mirror.
Stainless steel mirrors will differ in optic quality from glass mirrors.
In larger sizes, stainless mirrors are subject to distortion and/or "oil canning" for
which Bradley Corporation cannot accept responsibility.
Bradley mirrors are not field interchangeable from horizontal to vertical or vice versa.
Always specify width first.
Installation
Verify all rough-in dimensions prior to installation. Secure concealed mounting bracket to wall with screws (not included) at holes
provided. Mounting kits available through Bradley (ref. #899-026).
For more information, visit bradleycorp.com. Provide in-wall backing
at mounting screw locations. Position mirror over mounting bracket to
engage hanger tabs. Slide mirror down and lock into position.
Guide Specification
-4
-6
Mirror shall be framed with heavy gauge, one-piece roll-formed ¾"
x ¾" stainless steel angle with double strength continuous integral
stiffener. Welded corners shall be polished to a uniform satin finish.
Mirror shall be of first quality ¼" float glass guaranteed for 15
years against silver spoilage and protected by a shock-absorbing,
neoprene tubing with Poly-Glaze protective finish. Back of unit shall
be galvanized steel secure to frame with concealed screws, equipped
with integral horizontal hanging brackets and separate wall hanger
for concealed mounting.
Framed Mirror shall be Bradley Model
780‑______" W x______" H (specify width and height).
ADA Compliant
Consult local and national accessibility codes for proper installation
guidelines.
Conformity and compliance to local and national codes is the
responsibility of the installer.
780
Angle-Frame Mirror
Orders composed of products indicated as Bradex®
will be available to ship in three days after receipt of
order at the factory. There is no pricing penalty for
this service from Bradley.
Page 1 of 2 12/18/2012
This information is subject to change without notice.
Bradley_Mirror_780
P.O. Box 309, Menomonee Falls, WI 53052-0309
© 2014 Bradley
800 BRADLEY (800 272 3539) +1 262 251 6000
bradleycorp.com
780
Angle-Frame Mirror
Dimensions
“H”
“W”
MIRRORS 30" WIDE AND UNDER MIRRORS OVER 30" WIDE
½
mirror
width
2¼"
(57mm)
2"
(51mm)
7⁵⁄₈"
(193mm)
Outer
edge of
mirror
Bradex® Models
Dim. "A"
to finished
floor
Width
(Inches)
W
18" 30" 18 x 30 457 x 762 780-1830
18" 36" 18 x 36 457 x 914 780-1836*
24" 36" 24 x 36 610 x 914 780-2436*
24" 60" 24 x 60 610 x 1524 780-2460
Model 780 series angle framed mirrors can be fabricated to a
maximum size of 120"W x 72"H.
* Indicates available Tempered glass.
Height
(Inches)
H
Overall
Dimension
(Inches)
Bradex
7⁵⁄₈"
(193mm)
Overall
Dimensions
(Millimeters)
®
2¼"
(57mm)
Outer
edge of
mirror
2"
(51mm)
Standard
Model
Number
Dim. "A" Key Surface:
Mirror's bottom edge of
the reflecting surface to
finished floor
Rough wall opening:
Orders composed of products indicated as Bradex®
will be available to ship in three days after receipt of
order at the factory. There is no pricing penalty for
this service from Bradley.
Page 2 of 2 12/18/2012
This information is subject to change without notice.
Bradley_Mirror_780
For Dim. "A" Bottom of Unit
40" (1016mm) 39¼" (997mm)
37" (940mm) 36¼" (921mm)
34" (864mm) 33¼" (845mm)
Surface Mount: No rough wall opening, see overall dimensions
© 2014 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
800 BRADLEY (800 272 3539) +1 262 251 6000
bradleycorp.com
Loading...