Bradley Brand Furniture COMBI5500 User Manual
Installation
COMBI5500
17" Chase-Mounted Five-Sided
Stainless Steel Combination Unit
Table of Contents
Supplies Required ...........................2
Rough-In Information ...................... 2, 3
Installation Instructions .......................3
Cleaning Instructions ......................... 4
Bradley Security Fixtures are tamper resistant. All mounting hardware
Installation
THIS
SIDE
UP
215-329 Rev. K EN 08-703
© 2008 Bradley Corporation
Page 1 of 4 9/30/08
provided is essential for properly anchoring the unit. Bradley cannot
assume any responsibility for any improperly installed units. Read this
entire installation manual to ensure proper installation. When fi nished
with the installation, fi le this manual with the owner or maintenance
department. Compliance and conformity to local codes and ordinances is
Packing List
the responsibility of the installer.
•
•
•
•
Separate parts from packaging and make sure all parts are accounted for
before discarding packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Make sure that all water supply lines have been fl ushed and then completely
turned off before beginning installation. Debris in supply lines can cause
valves to malfunction.
Product warranties may be found under “Products” on our web site at
bradleycorp.com.
IMPORTANT!
P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1-800-BRADLEY Fax: 262-253-4161
www.bradleycorp.com
COMBI5500 Installation
Supplies Required:
• 1" NPT supply piping to flush valve
• Toilet/Lav waste connections
• For optional air valve manifold: 1/2" NPT supply piping. Refer to Bradley Installation Manual (215-1158) provided with assembly.
• For optional self-closing valve: 1/2" NPT supply piping. Refer to Bradley Installation Manual (215-581) provided with assembly.
• For optional TouchTime
®
solenoid valve: 1/8" NPT supply piping; wire nuts sized for 22 AWG to connect to 24 VAC power source.
Refer to Bradley Installation Manual (215-1378) provided with assembly.
Roughing-In Supplies, Drain, and Waste Outlet
Threaded
Studs (6)
All views are from the fi xture side
(right-hand unit shown).
Rough-in 1-1/4" or 1-1/2" NPT (size dependent
on options ordered) lavatory waste outlet at the
dimensions shown below. Use single or multiple
openings, depending on site requirements.
15"
(381)
Lav Waste
7/8" (22)
Dia. Holes [5]
7-1/2"
(190)
Top of integral seat is to be mounted 15" ( 381 mm)
above fi nished fl oor.
On fl oor outlet waste units, centerline of
waste is 4-1/4" (108mm) from wall.
(mm)
15"
(381)
2" X 15" (51 x 381)
Valve Mounting Hole
4" (102)
Square Hole
3" x 5"
(76 x 127)
Hole
Flush Valve
Supply
Toilet
Waste
Finished Floor
31-1/2"
(800)
4" (102)
34-1/2"
(876)
23-3/4"
(603)
15" (381)
Top of
Integral
Seat
11-1/4"
(286)
7"
(178)
Finished Floor
14"
(356)
7-3/4"
(197)
8" (203)
Square
Hole
4-1/2" (190)
20"
(508)
22"
(538)
31"
(787)
Single Opening in Wall* Multiple Openings in Wall
*Recommended when using optional wall sleeve
2 9/30/08 Bradley Corporation • 215-329 Rev. K; EN 08-703
Loading...