Bradley TERREON LD-3071/STD, TERREON LD-3072/STD, Terreon Lav Deck LD-3071/STDTerreon Lav Deck LD-3072/STD Installation Manual
Installation
LD-3071-3 shown
LD-3072-3 shown
Installation
Read this entire installation manual to ensure proper installation. When fi nished with
the installation, fi le this manual with the owner or maintenance department. Compliance
and conformity to local codes and ordinances is the responsibility of the installer.
LD-3071/STD
LD-3072/STD
Terreon® Lav Deck™ - 3070 Series
Table of Contents
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Supplies Required . . . . . . . . . . . . . . . . . . . . . . . .2
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Rough-Ins and Installation . . . . . . . . . . . . . . . . . .4
Cleaning and Maintenance . . . . . . . . . . . . . . . . .5
IMPORTANT!
Packing List
Separate parts from packaging and make sure all parts are accounted for before
•
•
•
IS
H
T
E
ID
S
P
U
discarding any packaging material. If any parts are missing, do not begin installation
•
until you obtain the missing parts.
Make sure that all water supply lines have been fl ushed and then completely turned off
before beginning installation. Debris in supply lines can cause valves to malfunction.
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior
to installation. Electrical power MUST remain off until installation is completed. After
installation is complete, turn on the water supply fi rst, then turn on the electrical power.
Hardware supplied by installer must be appropriate for wall construction. Wall anchors
used must have a minimum pull-out rating of 1,000 lbs.
Product warranties and service parts information may be found on our web site at
bradleycorp.com.
215-1640; EN 07-1111
© 2008 Bradley Corporation
Page 1 of 5 4/1/08
P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1-800-BRADLEY Fax: 262-253-4161
bradleycorp.com
LD-3071/STD, LD-3072/STD Installation
Optional Components
Contact your Bradley representative for Terreon® lav deck and sink options.
Stainless Steel Trap Cover
(186-1769)
5WL Textured Stainless Steel Trap Cover
(186-1770)
Support Bracket Assembly
(S45-2406)
1-1/2" Strainer/Tailpiece
(269-1584)
1-1/2" Polypropylene P-trap
(269-1697)
or
1-1/2" Polished Chrome-Plated
Brass P-trap
(S29-094)
Supplies Required:
• 3/8" wall anchors, bolts and washers to mount lav deck to wall (minimum pull-out rating of 1,000 lbs.)
• 1/2" NPT hot/cold or tempered supply piping
• 1-1/2" NPT drain piping
• Construction adhesive
• OPTIONAL: mounting brackets for Lav Decks (available from Bradley)
• OPTIONAL FOR STAINLESS STEEL TRAP COVER: four #10 wall anchors and mounting fasteners (for each cover) suitable for
wall construction
2 4/1/08 Bradley Corporation • 215-1640; EN 07-1111
Installation LD-3071/STD, LD-3072/STD
A
D
A
•
C
O
M
P
L
I
A
N
T
A
D
A
•
C
O
M
P
L
I
A
N
T
Dimensions
LD-3071-3/STD
35" (889mm)
4"
(102mm)
1"
(25mm)
vessel sink
rim height*
Dimensions for three-station lavs are shown. Dimensions for one-station and two-station lavs are similar.
Optional Centershank Drilling
Dim. A: 9-1/2" (381mm)
A
15" (381mm) 30" (762mm) 30" (762mm)
90" (2286mm)
34" (864mm)
vessel sink
rim height*
3"
(76mm)
2"
(51mm)
* Deck rim height to be 31" (787mm) above fi nished fl oor.
7-1/2" (191mm)
33" (838mm)
vessel sink
rim height*
3 places
Faucets supplied
by others
Terreon® solid
surface deck
Ø 1-3/8" (35mm)
3 places
11-1/2"
(292mm)
R 2" (51mm)
34"
(864mm)
31"
(787mm)*
17-1/2"
(445mm)
30"
(762mm)
21"
(533mm)
12-3/4"
(324mm)
LD-3072-3/STD
35" (889mm)
vessel sink
rim height*
4"
(102mm)
Optional Centershank Drilling
Dim. A: 9-1/2" (381mm)
A
15" (381mm)
30" (762mm) 30" (762mm)
34" (864mm)
vessel sink
rim height*
Faucets supplied
3"
by others
(76mm)
* Deck rim height to be 31" (787mm) above fi nished fl oor.
2"
(51mm)
90" (2286mm)
33" (838mm)
vessel sink
rim height*
5"
(127mm)
Terreon®
solid surface
deck
7-1/2" (191mm) 3 places
11-1/2"
(292mm)
34"
(864mm)
31"
(787mm)*
30"
(762mm)
17-1/2"
(445mm)
21"
(533mm)
12-3/4"
(324mm)
Bradley Corporation • 215-1640; EN 07-1111 4/1/08 3
LD-3071/STD, LD-3072/STD Installation
1
Rough-Ins
C
Fixture
L
15" (381mm)
Ref.
30"
(762mm)
Hot
41-1/2"
(1054mm)
Ref.
4" (102mm)
2" (51mm)
Sink
C
L
Cold
3-1/2"
(89mm)
7-3/4"
(197mm)
Sink
41-1/2"
(1054mm)
C
L
Ref.
30"
(762mm)
15" (381mm)
Ref.
3-3/4"
(95mm)
31"
(787mm)
Deck Rim
Height
Scribe a horizontal line 30-1/2" from fi nished fl oor.
Position the brackets with Terreon® strip at this height.
2
Installation
Apply construction
adhesive to Terreon
mounting strips
30-1/2"
(775mm)
Scribe
Line
Dim. A*
25"
(635mm)
Finished Floor
Dim. A*
24-3/4"
(629mm)
22"
(559mm)
(3) places
Waste
Dim. A*
16" (406mm)
(3) places
* For Trap Cover (shown in "right-mounted faucet" position.)
Wall-Mount Faucet Dim. A: 8" (203mm)
Faucet mount - left of vessel Dim. A: 6-1/2" (165mm)
Faucet mount - right of vessel Dim. A: 9-1/2" (241mm)
Faucets by others
®
The vessel sinks are pre-mounted to the deck prior to shipping.
4 4/1/08 Bradley Corporation • 215-1640; EN 07-1111
Drain and P-trap
installation
Installation LD-3071/STD, LD-3072/STD
Cleaning and Maintenance for Terreon
®
Material Description: Terreon® is an NAHB Certifi ed densifi ed solid surface material composed of polyester resin and is resistant
to chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleansers or fi ne grit abrasives.
Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household cleaner such as
Formula 409
Stubborn Stains: Remove tough stains with Ajax
circular motion with 240 grit wet/dry sandpaper. The fi nish can be renewed with a maroon Scotch-Brite
®
or Windex®.
®
, Comet®, or Soft-Scrub® and a green Scotch-Brite® pad or lightly sand in a
®
pad.
Special Situations for Terreon Material
Scratches: Remove scratches with a green Scotch-Brite® pad. The fi nish can then be renewed with a maroon Scotch-Brite®
pad, followed by a white Scotch-Brite
Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit
thoroughly after cleaning.
Restoring the surface: Use Hope’s
material. Bradley recommends additional care and maintenance for the darker colored Terreon
this additional maintenance refer to Bradley technical document #1505.
Do not use strong acid or alkaline chemicals and cleansers to clean Terreon
contact with the surface, wipe them off immediately and rinse with soapy water. Avoid contact with harsh
chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot pans and objects.
Repair Kits: Terreon
®
repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing
Repair kits are made to order and have a shelf life of 30 days.
Terreon
®
is a unique, cast solid surface material. Aggregate fl ow and distribution as well as shades of color can vary from
product to product creating natural characteristics.
®
pad or 30-micron sandpaper.
®
Solid Surface cleaner and polish to refresh and protect the Terreon® Solid Surface
®
, for complete instructions on
®
. If these chemicals come in
Cleaning Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly
under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more complicated.
Routine Cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the cleaning
solution per the manufactures instructions and always use a soft cloth or sponge to avoid damaging the fi nish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball® stainless steel
cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same direction as the polish lines.
Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool or stainless
steel brushes.
Special Situations for Stainless Steel Material
Fingerprints and Smears: To remove fi ngerprints or smears use a high quality stainless steel cleaner and polish in accordance
with the manufactures instructions. Many of these products leave a protective coating the helps prevent future smears and
fi ngerprints.
Grease and Oil: Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in
accordance to the manufactures instructions and in the direction of the polish lines.
Precautions: Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates
(pesticides, photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions
exist.
Do not permit salty solutions to evaporate and dry on stainless steel.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual source
of the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.
Strongly acidic or caustic cleaners may attack the steel causing a reddish fi lm to appear. The use of these
cleaners should be avoided.
Brand Names
Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the omission
of any brand name cleaner imply inadequacy. Many products named are regional in distribution, and can be found in local
supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products should be used
in strict accordance with package instructions.
Bradley Corporation • 215-1640; EN 07-1111 4/1/08 5
Loading...