Bradley S19-300T, S19-300B Installation Manual
Installation
S19-300T (top supply)
S19-300B (bottom supply)
Heat Trace Combination Drench
Shower and Eyewash Unit Class 1,
Div. 1, Groups C & D
(includes 120 V and 220/240 V
versions)
Table of Contents
Pre-Installation Information ..................2-3
Assembly of Components .....................4
Installation ...............................5–6
Repair Parts List ..........................6–7
Troubleshooting .............................8
215-1308 Rev. F; ECN 17-05-045
© 2017 Bradley
Page 1 of 8 6/5/2017
Menomonee Falls, WI 53052 USA
P.O. Box 309
800 BRADLEY (800 272 3539)
+1 262 251 6000
bradleycorp.com
S19-300T, S19-300B—Class 1, Div. 1, Groups C & D Installation
WARNING
Flush the water supply lines before beginning installation and after installation is complete. Test
the unit for leaks and adequate water flow.
Main water supply to the unit should be "ON" at all times unless system is being serviced.
Provisions shall be made to prevent unauthorized shutoff.
Power supplied to the unit should be 120VAC or 220-240VAC, 50-60 Hz, 15 amp branch circuit with
a dedicated circuit breaker or fuse and should not supply power to any other device. Compliance
and conformity to local codes and ordinances is the responsibility of the installer.
Do not use this safety equipment in a location that does not match its hazardous location rating.
Verify the appropriate ratings prior to installation.
When making electrical connections be sure to follow all lockout-tagout safety procedures.
CAUTION
Emergency equipment must be supplied with tepid water (60-100°F/15.6-37.8°C). Any prolonged
exposure to near freezing water affects the body's ability to maintain body temperature, increasing
the risk of hypothermia.
The unit must be supplied with clean, potable water.
NOTICE
Before installing this product ensure that there are adequate clearances around the product and
activation of the product does not interfere with other products or obstructions.
It is recommended that all water supply and electrical connections be made at temperatures above
freezing. Failure to do so may result in major product and/or property damage.
Constant power supply to the safety equipment is necessary for it to function.
Avoid cleaners containing organic solvents, alcohols and hydrocarbons. Rinse with potable water
after cleaning.
2
6/5/2017 Bradley • 215-1308 Rev. F; ECN 17-05-045
Installation S19-300T, S19-300B—Class 1, Div. 1, Groups C & D
IMPORTANT
The installation and location of all safety drench showers, eye and eye/face washes must comply
with the requirements of ANSI/ISEA Z358.1.
Read this installation manual completely to ensure proper installation, then file it with the owner
or maintenance department. Compliance and conformity to local codes and ordinances is the
responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding any
packaging material. If any parts are missing, do not begin installation until you obtain the missing
parts.
Installation and maintenance of this system must be completed by a qualified plumber and
electrician according to the information contained in this installation manual and in compliance
with all national and local codes.
The ANSI/ISEA Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley
plumbed emergency fixtures require a minimum of 30 PSI (0.21MPa) flowing pressure. Flushing
should be tepid per ANSI Z358.1
Weekly activation must be conducted on all plumbed emergency equipment to ensure a suitable
flushing fluid supply is present and any sediment build up in the supply line is cleared. Inspect
safety equipment monthly to address any maintenance issues ensuring the equipment is in good
operating condition and that there are no signs of wear.
Perform functional test upon relocation of safety equipment.
The inspection and testing results of this equipment should be recorded weekly to verify proper
operation. This equipment should be inspected annually to enure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be trained
regarding the placement and proper operation of emergency equipment per ANSI/ISEA Z358.1.
For questions regarding the operation or installation of this product, visit www.bradleycorp.com or
call 800-BRADLEY (272.3539).
Product warranties and parts information may also be found under ”Products” on our web site at
bradleycorp.com.
Bradley • 215-1308 Rev. F; ECN 17-05-045 6/5/2017
3
Loading...