S19-240
Installation
S19-240, S19-240FW
Unmounted Eyewash and Eye/Face
Wash for Laboratory Application
Table of Contents
Pre-Installation Information ....................... 2
Installation Instructions .......................... 3
S19-240 Components and Parts List ............... 4
S19-240 Components and Parts List ............... 5
S19-240FW
215-161 Rev. N; ECN 12-05-003C
© 2012 Bradley
Page 1 of 5 10/19/2012
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX 262.251 5817
bradleycorp.com
S19-240, S19-240FW Installation
IMPORTANT
Installation
R
WI 53051
alls,
HENTLICH ZU
WEEK
WÖC
P.O. Box 309, Menomonee F
DAIRE
e(s) each week and sign
UNIT EACH
y malfunctions immediatel
hentlich im
TEST THIS
hrift. Jeglic
DIESES GERÄT 1ST
ESSAI HEBDOMA
Test-operate valv
Report an
Ventil(e) wöc
t immédiatement.
durch Untersc
Test le fonctionnement des v
signe en bas. S'il y à quelqu
un rappor
Date
Datum
Date
114-051
PRÜFEN.
Testbetrieb prüfen,
he Störung sofor
Signed
Unterschrift
below.
bestätigt
t melden.
y.
alves chaque semaine et
e chose qui ne v
Date Signed
Signe
THIS
SIDE
UP
a pas fait
Signed
Signed
Date
Date
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
Packing List
•
•
•
•
Read this installation manual completely to ensure proper installation, then file it with the
owner or maintenance department. Compliance and conformity to drain requirements and
other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding
any packaging material. If any parts are missing, do not begin installation until you obtain the
missing parts.
Flush the water supply lines before beginning installation and after installation is complete.
Test the unit for leaks and adequate water flow. Main water supply to the eye/face wash should
be “ON” at all times. Provisions shall be made to prevent unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley plumbed
emergency fixtures require a minimum of 30 PSI (0.21 MPa) flowing pressure. Flushing fluid
should be tepid per ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly to verify
proper operation. This equipment should be inspected annually to ensure compliance with
ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be trained
regarding the placement and proper operation of emergency equipment per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit www.bradleycorp.
com or call 1-800-BRADLEY.
Product warranties and service parts information may also be found under ”Products” on our
web site at www.bradleycorp.com.
2
10/19/2012 Bradley • 215-161 Rev. N; ECN 12-05-003C
Installation S19-240, S19-240FW
Installation
NOTICE! Avoid cleaners containing organic
solvents, alcohols, and hydrocarbons.
Rinse with water after cleaning.
Supplies Required:
• Pipe sealant
• Piping to ½" NPT water supply inlet
• Sign-mounting hardware
• Backflow prevention device as required by
UPC, IPC and/or local plumbing codes
Local codes may require the installation of a
backflow prevention valve to complete proper
installation. Compliance with local codes is the
responsibility of the installer. Valve must be
tested annually to verify that it is functioning
properly. Backflow prevention valves are not
included with the fixture and may be supplied
by the contractor or purchased from Bradley
Corporation.
6³⁄₈"
(162mm)
(89mm)
5⁵⁄₈"
(143mm)
3½"
S19-240
½" NPT
Supply Inlet
13⁵⁄₈"
(340mm)
5¼"
(133mm)
Step 1: Assemble components
The top of the eyewash heads should be 33"–
45" (838mm–1143mm) from the floor.
1. Assemble the components as shown on page 4
(for S19-240) or page 5 (for S19-240FW).
• Apply pipe sealant (supplied by installer) to
all male-threaded pipe joints.
• Use a strap wrench around pipes
when tightening to prevent marring the
BradTect® protective, safety yellow coating.
Step 2: Connect water supply
1. Connect the water supply piping (by installer) to
the ½" NPT inlet on the eyewash.
2. Open the water supply lines. Test for leaks and
adequate water flow.
3. Mount the safety sign to the wall using the signmounting hardware supplied by the installer.
All dimensions assume standard thread
engagement. Variations in manufacturing allow
for +/- ¹⁄₈” (3mm) per threaded joint. To find
the tolerance of a dimension, add the number
of thread joints in between a dimension and
multiply it by ¹⁄₈” (3mm).
6³⁄₈"
(162mm)
7¼"
(184mm)
S19-240FW
½" NPT
Supply Inlet
3½"
(89mm)
5¼"
(133mm)
13⁷⁄₈"
(352mm)
Bradley • 215-161 Rev. N; ECN 12-05-003C 10/19/2012
3
S19-240, S19-240FW Installation
Assembly of Components and Parts List — S19-240
2
R
P.O. Box 309, Menomonee Falls, WI 53051
TEST THIS UNIT EACH WEEK
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
10
un rapport immédiatement.
Date
Signed
Datum
Unterschrift
Date
Signe
1
Date Signed
Date
Date
11
Signed
Signed
3
Flow Control
This End
4
5
Item Part No. Qty Description
1 S05-091 1 Eyewash Yoke
2 107-371 2 Dust Cover
½" NPT
Supply Inlet
7
8
6
9
7.1
Item Part No. Qty Description
7 S27-327 1 ½" NPT Ball Valve w/Nut
7.1 110-215 1 Nut Only
3 S21-077 1 Stem
4 169-1023A 1
Elbow ½" x ³⁄₈" Chrome
5 113-965 1 Pipe ½" x 3½"
6 169-862 1 ½"NPT Street Elbow
(Chrome)
4
10/19/2012 Bradley • 215-161 Rev. N; ECN 12-05-003C
8 128-135 1 Handle
9 142-002DA 1 Lockwasher
10 114-051 1 Safety Sign
11 204-421 1 Emergency Inspection Tag
Installation S19-240, S19-240FW
Assembly of Components and Parts List — S19-240FW
3
2
R
P.O. Box 309, Menomonee Falls, WI 53051
TEST THIS UNIT EACH WEEK
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
2
11
1
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
Date
Signed
Date Signed
Datum
Unterschrift
Date
Date
Signe
Date
12
Signed
Signed
4
5
6
Item Part No. Qty Description
1 S05-091P 1 Eyewash Yoke
2 S45-2453 1 Service Kit EFW - Black
Sprayheads
3 S53-063 2 Dust Cover
4 113-1191 1 Stem Pipe
5 169-1023A 1
6 113-596 1 Pipe Nipple
Elbow ½" x ³⁄₈" Chrome
½" NPT
Supply Inlet
8
9
7
10
8.1
Item Part No. Qty Description
8 S27-327 1 ½" NPT Ball Valve w/Nut
8.1 110-215 1 Nut Only
9 128-135 1 Handle
10 142-002DA 1 Lockwasher
11 114-051 1 Safety Sign
12 204-421 1 Emergency Inspection Tag
7 169-862 1 ½"NPT Street Elbow (Chrome)
Bradley • 215-161 Rev. N; ECN 12-05-003C 10/19/2012
5
Loading...