Bradley EXD-2N Installation Instructions Manual
Installation
Instructions
Table of Contents
Dimensions . . . . . . . . . . . . . . . . . . . . . . .2–3
Rough-Ins . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Installation Instructions . . . . . . . . . . . . . .6–9
Cleaning and Maintenance . . . . . . . . . . . .10
Assembly of Components . . . . . . . . . . . . .11
Vernatherm™ Valve Troubleshooting . . . .12
Vernatherm™ Valve Repair Parts . . . . . . .13
EXD-2N
Express® Deck Lavatory
System EXD-Series
(Standard and Wall-Hung Pedestals)
Express® Decks are ADA
and TAS compliant.
215-1542 Rev. E; EN 06-915
© 2007 Bradley Corporation
Page 1 of 13 2/9/07
P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY FAX 262-251-5817
http://www.bradleycorp.com
IMPORTANT
Read this entire installation manual to ensure proper installation, then file these
instructions with the owner or maintenance department.
Flush all the water supply lines before making connections. Debris in supply
lines will cause the valves to malfunction.
Turn OFF electrical power to the outlet when installing the Express® Deck.
Wall anchors used must have a minimum pull-out rating of 1,000 lbs.
Product warranties may be found under "Product Information" on our web site at
www.bradleycorp.com.
A
D
A
C
O
M
P
L
I
T
N
A
2
Express® Deck Lavatory System EXD-Series
EXD-2N Installation Instructions
2/9/07 Bradley Corporation • 215-1542 Rev. E; EN 06-915
EXD-2N/STD and EXD-2N/WH
Express® Deck Lavatory System Dimensions
50"
(1270mm)
8"
(203mm)
RADIUS
10"
15"
(381mm)
15"
(381mm)
(254mm)
RADIUS
STANDARD
HEIGHT
WALL-HUNG
HEIGHT
7"
(178mm)
21-1/4"
(540mm)
30"
(762mm)
36"
(914mm)
7"
(178mm)
30"
(762mm)
36"
(914mm)
3
Express® Deck Lavatory System EXD-Series
Installation Instructions EXD-2N
Bradley Corporation • 215-1542 Rev. E; EN 06-915 2/9/07
Express® Deck Lavatory System Dimensions continued . . .
21-1/8"
(537mm)
11-1/2"
STANDARD HEIGHT
34"
(864mm)
30"
(762mm)
(292mm)
8-5/8"
(219mm)
WALL-HUNG
MOUNTED AT
STANDARD HEIGHT
34"
(864mm)
30"
(762mm)
13-1/4"
(337mm)
A
D
A
C
O
M
P
L
13-1/4"
(337mm)
21-1/8"
(537mm)
T
I
N
A
11-1/2"
(292mm)
8-5/8"
(219mm)
A
D
A
C
O
M
P
T
L
I
N
A
3" (76mm)
SCUFF BASE
STANDARD
HEIGHT ONLY
WALL-HUNG
MOUNTED AT
JUVENILE HEIGHT
AGES 6 THROUGH 12
31"
(787mm)
27"
686mm)
10-1/4"
(260mm)
D
A
C
O
M
P
A
T
L
I
N
A
21-1/8"
(537mm)
11-1/2"
(292mm)
(219mm)
8-5/8"
WALL-HUNG
MOUNTED AT
TAS HEIGHT
GRADES PRE-K
THROUGH 5 OR 6
30"
(762mm)
26"
(660mm)
9-1/4"
235mm)
TAS
21-1/8"
(537mm)
11-1/2"
(292mm)
(219mm)
8-5/8"
WALL-HUNG
MOUNTED AT
TAS HEIGHT
GRADES 6
THROUGH 8 OR 9
32"
(813mm)
28"
(711mm)
11-1/4"
(286mm)
TAS
21-1/8"
(537mm)
11-1/2"
(292mm)
(219mm)
8-5/8"
4
Express® Deck Lavatory System EXD-Series
EXD-2N Installation Instructions
2/9/07 Bradley Corporation • 215-1542 Rev. E; EN 06-915
Installation Instructions
Supplies required for installation:
• (6) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall
(minimum pull-out rating of 1,000 lbs.)
• STD. HEIGHT ONLY: (2) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount scuff
base to wall
• 1/2" NPT hot and cold supply piping
• 1-1/2" NPT drain piping
• 110 volt electrical outlet for optional 110/24 VAC plug-in transformer, if required
• (2) #10 wall anchors and fasteners for optional Vernatherm™ valve mounting
• 240/208-volt or 277-volt electrical box for optional electric tankless water heater
Step 1: Rough in
IMPORTANT: Dimensions shown in Figure 1 on page 5 are for a Standard and Wall-
Hung Pedestal Express® Deck only. Make sure to follow appropriate
dimensions based on configuration and required rim height. See
Charts 1 and 2 on page 5 before beginning rough-ins.
1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown.
2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown.
3. FOR OPTIONAL ELECTRIC FAUCETS: Install the 110 volt GFCI electrical outlet per local
code at the location shown in Figure 1.
4. Install four to six 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by
installer) at the locations shown in Figure 1.
5. On the back of the bowl, measure the distance between the 3/4" bowl mounting holes. Divide
this measurement in half. Measure and mark this dimension on the wall to the left of the
centerline and to the right of the centerline. Install two 3/8" wall anchors with a minimum pullout rating of 1,000 lbs. (supplied by installer) at the locations marked (ref. location “A” shown in
Figure 1).
NOTE: Wall anchors at location “C” (standard frame only) do not require a minimum pull-out
rating of 1,000 lbs.
NOTE: The anchors will be used to mount the Express® Deck bowl and frame to the wall.
Loading...