Bradford-White Corp Powered Direct Vent User Manual

POWERED DIRECT VENT SERIES GAS-FIRED

WATER HEATER

A Spanish language version of these instructions is available by contacting the company listed on the rating plate. La version espanola de estas instrucciones se puede obtener al escribile a la fabrica cuyo nombre aparece en la placa de especificaciones.

PDX INSTALLATION AND OPERATING

INSTRUCTION MANUAL

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable,

combustible, or corrosive vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier's instructions.

INTERNET VERSION FOR REFERENCE ONLY

• If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience we recommend Bradford White water heaters to be installed and serviced by a plumbing professional.

238-42047-00F REV 10/04

CONGRATULATIONS!

You have just purchased one of the finest water heaters on the market today!

This installation, operation and instruction manual will explain in detail the installation and maintenance of your new Powered Direct Vent Series Gas-Fired Residential Water Heater. We at Bradford White strongl y recommend that you contact a plumbing professional for the installation of this water heater.

We require that you carefully read this manual, as well as the enclosed warranty, and refer to it when questions arise. If you have any specific questions concerning your warranty, please consult the plumbing professional from whom your water heater was purchased. For your records we recommend that you write the model, serial number and installation date of your water heater in the maintenance section in the back of this manual.

This manual should be kept with the water heater.

At Bradford White we’re committed to providing you with

INTERNET VERSION FOR REFERENCE ONLY

TABLE OF CONTENTS

page

GENERAL INFORMATION............................................................ 4

INSTALLATION. ............................................................................. 5

Locating The Water Heater.................................................... 5

Minimum Clearances ............................................................... 8

Venting...................................................................................... 8

Water Connections.................................................................. 22

Gas Connections..................................................................... 25

Electrical Connections ........................................................... 26

Wiring Diagram .................................................................. 27

GENERAL OPERATION................................................................ 28

Lighting and Shutdown Instructions..................................... 29

Thermostat Adjustment .......................................................... 30

Burner Flame Check............................................................... 31

MAINTENANCE.............................................................................. 32

PARTS LIST AND DRAWING........................................................ 35

BLOWER PARTS LIST AND DRAWING....................................... 36

INSTALLATION INSTRUCTIONS FOR POTABLE WATER AND

SPACE HEATING........................................................................... 37

VENT PIPE PREPARATION AND JOINING................................. 38

NOTES............................................................................................ 40

INTERNET VERSION FOR REFERENCE ONLY

GENERAL INFORMATION

This gas -fired water heater’s design is certified by CSA International under the

American National Standard Z21.10.1 - (as indicated on the rating plate) and CSA 4.1-M - (as indicated on the rating plate).

This water heater must be installed in accordance with local codes or, in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions). The warranty for this water heater is in effect only when the water heater is installed, adjusted, and operated in accordance with these Installation and Operating Instructions. The manufacturer will not be held liable for any damage resulting from alteration and/or failure to comply with these instruc tions.

This water heater is not design certified for installation in a mobile home. Such an installation may create a hazardous condition and will nullify the warranty.

CAUTION

Incorrect operation of this appliance may create a hazard to life and property and will nullify the warranty.

Do not use this appliance if any part has been submerged in water. You should contact a qualified service technician to inspect the appliance and to replace any part of the control system including the combination gas control, which has been submerged in water.

DANGER

Do not store or use gasoline or other flammable, combustible, or corrosive vapors and liquids in the vicinity of this or any other appliance.

IMPORTANT

Before proceeding, please inspect the water heater and its components for possible damage. DO NOT install any damaged components. If damage is evident then please contact the supplier where the water heater was

INTERNET VERSION FOR REFERENCE ONLY

purchased or the manufacturer listed on the rating plate for replacement parts.

Make sure that you check the rating plate and combination gas control on the water heater to be certain that the type of gas being supplied corresponds with the marking on the rating plate and combination gas control.

General Information continued -

A sacrificial anode is used to extend tank life. The removal of this anode, for any reason, will nullify the warranty. In areas where water is unusually active, an odor may occur at the hot water faucet due to a reaction between the sacrificial anode and the impurities in the water. If this should happen, an alternative anode may be purchased from the supplier that installed this water heater. This will minimize the odor while protecting the tank. Additionally, the water heater should be flushed with appropriate dissolvers to eliminate any bacteria.

INSTALLATION

Locating The Water Heater

WARNING

Water heaters are heat -producing appliances. To avoid damage or injury, do not store materials against the water heater or vent -air intake system. Use proper care to avoid unnecessary contact (especially by children) with the water heater and ve nt-air intake components. UNDER NO CIRCUMSTANCES MUST

FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER OR VENT-AIR INTAKE SYSTEM.

DO NOT install the water heater in any location where gasoline or flammable vapors are likely to be present.

CAUTION

The National Fuel Gas Code (ANSI Z233.1-or latest edition) and CAN/CGA (B149.1-or latest edition), expressly prohibits the installation of a water heater in a garage, unless the unit is installed so that the burner and ignition devices are at least eighteen (18) inches (46 cm) above floor level and protected to avoid damage by a moving vehicle.

The location of this water heater is of the utmost importance. Before installing this water heater, read the installation section of these instructions. After reading

INTERNET VERSION FOR REFERENCE ONLY

these installation and operating instructions, select a location for the water heater where the floor is level and is easily accessible to gas and water supply lines. DO

NOT locate the water heater where water lines could be subjected to freezing temperatures. Make sure the cold water pipes are not located directly above the gas control so that condensate during humid weather does not drip on the controls.

Installation (Locating The Water Heater) continued -

Water heater corrosion and component failure can be caused by the heating and breakdown of airborne chemical vapors. Examples of some typical compounds that are potentially corrosive are: spray can propellants, cleaning solvents, refrigerator and air conditioning refrigerants, swimming pool chemicals, calcium and sodium chloride, waxes and process chemicals. These materials are corrosive at very low concentrat ion levels with little or no odor to reveal their presence. NOTE: DAMAGE TO THE WATER HEATER CAUSED BY EXPOSURE

TO CORROSIVE VAPORS IS NOT COVERED BY THE WARRANTY. DO NOT OPERATE THE WATER HEATER IF EXPOSURE HAS OR WILL OCCUR. DO NOT STORE ANY POTENTIALLY CORROSIVE COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

WARNING

Liquefied petroleum gases/propane gases are heavier than air and will remain at floor level if there is a leak. Basements, crawl spaces, closets and areas below ground level will serve as pockets for accumulation of leaking gas. Before lighting, smell all around the appliance area for gas. Be sure to smell next to the floor.

IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any telephone in

your building.

• Immediately call your gas supplier from a neighbor’s

telephone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

DO NOT OPERATE APPLIANCE UNTIL THE LEAKAGE IS CORRECTED!

INTERNET VERSION FOR REFERENCE ONLY

Installation (Locating The Water Heater) continued -

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE NOT CERTAIN OF THE FOLLOWING:

• Liquefied petroleum gases/propane gas and natural gas have an

odorant added by the gas supplier that aids in the detection of the gas.

• Most people recognize this odor as a “sulfur” or “rotten egg” smell.

• Other conditions, such as “odorant fade” can cause the odorant to

diminish in intensity, or ”fade”, and not be as readily detectable.

• If you have a diminished sense of smell, or are in any way unsure of

the presence of gas, immediately contact your gas supplier from a neighbor’s telephone.

• Gas detectors are available. Contact your gas supplier, or plumbing

professional, for more information.

The water heater must be located close enough to the outside wall to keep the venting distance within the maximum distance described in the installation instructions. Read the venting section in this installation instruction manual before locating the water heater.

This water heater must be located in an area where leakage of the tank or water line connections and the combination temperature and pressure relief valve will not result in damage to the area adjacent to the water heater or to lower floors of the structure. When such locations cannot be avoided, a suitable drain pan adequately piped for proper drainage, must be installed under the water heater. The drain pan must be no greater than 1-½ inches (3.8 cm) deep and have a minimum length and width of at least four (4) inches (10.2 cm) measured from the jacket of the water heater. The drain pan, as described above, can be purchased from your plumbing professional. The drain pan must be piped to an adequate drain. The piping must be at least 3/4 inch (1.9 cm) in diameter and pitched for proper drainage.

It is recommended that a minimum clearance of four (4) inches (10.2 cm) be provided on the side of the water heater for servicing and maintenance of the combination temperature and pressure relief valve.

INTERNET VERSION FOR REFERENCE ONLY

Installation (Minimum Clearances) continued -

Minimum Clearances

WARNING

Failure to adhere to these installation and operating instructions may create a hazard to life and property and will nullify the warranty.

This installation must allow access to the front of the water heater and adequate clearance must be provided for servicing and operating this water heater. The water heater may be installed on either a combustible or non-combustible floor. If the water heater is to be installed directly on carpeting, it must be installed on top of a metal or wood panel extending beyond the full width and depth of the appliance by at least three (3) inches (7.6 cm) in any direction or, if the appliance is to be installed in an alcove or closet, the entire floor must be covered by the panel. The minimum clearances to combustibles for this water heater is: zero (0) inches (0 cm) from the sides and rear, five (5) inches (12.7 cm) from the front of the jacket, zero (0) inches (0 cm) from the vent connector and fifteen (15) inches (38.1 cm) from the jacket top.

Venting

The National Fuel Gas Code ANSI Z223.1-(Latest Edition), CGA/CAN B149 Installation Code, and local codes have specific requirements for the location of the vent terminals on vertical walls. The guidelines listed below are from the National Fuel Gas Code. Consult the local codes, and/or National Fuel Gas Code ANSI Z223.1-(Latest Edition), or CGA/CAN B149 Installation Code to determine if there are any additions or changes to the following specifications.

(A) The vent terminals must terminate at least 3 feet (.91 m) above any forced

air inlet duct located within 10 feet (3 m). Exception: This provision shall not apply to the combustion air intake of a direct vent appliance.

(B) The vent terminals must terminate at least 12 inches (.31 m) below, 12

inches (.31 m) horizontally from, or 12 inches (.31 m) above any door, window, or any gravity air inlet into the building.

12 inches (.31 m) above grade. Note: Must be installed in a location where it will not be blocked by

INTERNET VERSION FOR REFERENCE ONLY

snow.

(D) The vent terminals must not terminate over a public walkway or over an

area where condensate or vapor could create a nuisance or hazard or could be detrimental to the operation of regulators, relief valve, or other equipment.

(E) The water heater location must provide easy access for the entire length

of the vent connector.

Venting continued -

(F) The vent system must be inspected at least once a year to ensure

against leakage of exhaust products.

Exceptions For Installations in Canada:

(A) The vent terminals must be located at least 1 foot (.31 m) from any

window or door, which can be opened in any building, any non-mechanical air supply inlet to any building, or the combustion air inlet to any other appliance.

(B) The vent terminals must be located at least 6 feet (1.8 m) from any

mechanical air supply inlet to the building.

or within 3 feet (.91 m) horizontally of the vertical centerline of the regulator and must be at least 6 feet (1.8 m) from any gas service regulator vent outlet.

(D) The vent terminals must be at least 7 feet (2.1 m) above a paved sidewalk

or a paved driveway located on public property.

(E) The vent terminals must not terminate above a paved sidewalk or a paved

driveway, which is located on adjacent private property.

(F) Underneath a verandah, porch or deck, unless:

(1.) Th e verandah, porch or deck is fully open on a minimum of two

sides beneath the floor, and

(2.) The distance between the top of the vent-air intake terminal and the

underside of the verandah, porch or deck is greater than 1 ft (30.5 cm).

INTERNET VERSION FOR REFERENCE ONLY

Venting continued -

Venting Installation Instructions For Supplied Intake Venting:

1. Refer to Figure 1, “Vent Assembly Illustration” to install intake venting as described below.

2. Insert one end of the Vertical Pipe into Metal Boot on the lower backside of the water heater.

3. Slide the Support Bracket over the Vertical Pipe, but do not fasten to the Jacket Head.

4. Position the Intake Tee on top of the Vertical Pipe so that the short straight section of the tee faces the Blower Intake Collar, and the curve of the tee faces upward. Proper orientation of the curved

section of the tee is critical. Be sure it is facing upward. Refer to “This End Up” label on Intake Tee.

5. Slide the Rubber Intake Elbow over the Blower Intake Collar and over the short straight section of the Intake Tee.

6. Using a level to ensure that the Vertical Pipe is straight up and down, secure the Vertical Pipe to the Jacket Head using the Support Bracket and three (3) self-drilling screws provided. NOTE: Correct vertical positioning of the Vertical Pipe is Important.

7. After securing the Vertical Pipe to the Jacket Head with the Support Bracket, tighten the clamps on the Rubber Intake Elbow.

8. Using the RTV sealant provided, place a bead of RTV around the Vertical Pipe at the Metal Boot location, and at the Intake Tee location. Smooth out the RTV to provide a seal at both locations.

9. Two 90° end terminal elbows are supplied. These must be installed at the extreme ends of the intake and exhaust venting outside the building. The end terminal with the external screen must be installed on the intake vent as shown in Figure 7.

10. Proceed as necessary to complete the venting installation as described in the venting section of this manual.

INTERNET VERSION FOR REFERENCE ONLY

Venting continued -

INTERNET VERSION FOR REFERENCE ONLY

Figure 1

Vent Assembly Illustration

Venting continued -

Venting System Condensation

Condensate formation does not occur in all installations of power vented heaters, but should be protected against on installations where condensation can form in the venting system.

Formation of condensation in the venting system of Power Vented water heaters is dependent upon installation conditions including, but not limited to:

ambient temperature and humidity of installation location;

ambient temperature and humidity of venting space;

vent distance and slope;

and product usage.

In order to effectively control condensate from adversely affecting the mechanical components of the water heater several methods may be employed:

1. For horizontal installations the vent pipe can be installed with a downward slope (not less than 1/8" nor greater than ½” per foot maximum) and away from the blower motor.

2. In order to prevent condensate from draining back into the blower (vertical or horizontal runs), a fitting and drain hose is available as a condensate trap kit (see Table 1 for service part numbers). The all rubber fitting with drain outlet mounts directly to the blower motor outlet and is secured with two hose clamps (one to the blower motor outlet and the other to the vent connector). The plastic tubing is provided to drain any accumulated condensate away from the water heater and to a suitable drain. The kit comes complete with instructions for proper installation of the fitting.

Table 1

Model Service Part

2” (5.1 cm) Blower Outlet (exhaust) 239-42742-00 3” (7.6 cm) Blower Outlet (exhaust) 239-42743-00

INTERNET VERSION FOR REFERENCE ONLY

Venting continued -

3. In order to prevent condensate from draining back into the blower (vertical or horizontal runs), a drain tee and condensate trap can be installed in the horizontal vent as close as practical to the blower vent connection (see Figure 2). The condensate disposal tube should be installed to drain any accumulated condensate away from the water heater and to a suitable drain. The drain tee and condensate hose are not available from Bradford White, but should be available through your local distributor.

Figure 2

INTERNET VERSION FOR REFERENCE ONLY

+ 30 hidden pages

Bradford-White Corp Powered Direct Vent User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual